48.

Review the data on the screen and select Next.

XXXXX
XXXXX

XXXXXXXXXXXXXXXX

Figure 35

49.

Follow the on-screen instructions and select Next.

Figure 36

19/41

NTB20-095

50.

Confirm the battery voltage is within acceptable limits, and then select Start.

Figure 37

51.

Select your user group from the drop down menu, then select OK.

Figure 38

20/41

NTB20-095

52.

Enter your Username and Password, and then select Submit.

Figure 39

53.

Allow Transfer Data to complete.

Figure 40

21/41

NTB20-095

54.

Once the update completes, select Next.

Figure 41

55.

Erase All DTCs.


Follow the on-screen instructions as shown in Figure 42 and Figure 43.

Figure 42

22/41

NTB20-095



Select Next.

Figure 43

56.

Select Confirm.

XXXXX
XXXXX

XXXXXXXXXXXXXXXX

Figure 44

23/41

NTB20-095

57.

If the screen in Figure 45 displays, select Home. If the screen in Figure 45 does not
display, skip to step 58.

Figure 45

58.

Select Re/programming, Configuration.

Figure 46

24/41

NTB20-095

59.

Use the arrows (if needed) to view and read all precautions.

Figure 47

60.

Select Confirmed instructions.

61.

Select Next.

Figure 48

25/41

NTB20-095

62.

Select the correct vehicle information.

63.

Select OK.

Figure 49

64.

Verify the correct VIN is populated.

65.

Select Confirm.

XXXXXXXXXXXXXXX

Figure 50

26/41

NTB20-095

66.

Select Confirm.

XXXXXXXXXXXXXXXXXXXX

Figure 51

67.

Select ALL MODE AWD/4WD.

Figure 52

27/41

NTB20-095

68.

Select After ECU Replacement.

Figure 53

69.

Read the precautions.

Figure 54

28/41

NTB20-095

70.

Select Manual selection.

Figure 55

71.

Use the arrows (if needed) to view and read all precautions.

Figure 56

29/41

NTB20-095

72.

Select Confirmed instructions.

73.

Select Next.

Figure 57

74.

75.

Under ROM Data ID, select 416596RR0D.

Select Next.

Figure 58

30/41

NTB20-095

76.

Review the data on the screen and select Next.

XXXXX

XXXXXXXXXXXXXXXX

Figure 59

77.

Follow the on-screen instructions and select Next.

Figure 60

31/41

NTB20-095

78.

Confirm the battery voltage is within acceptable limits, and then select Start.

Figure 61

79.

Allow Transfer Data to complete.

Figure 62

32/41

NTB20-095

80.

Once the update completes, select Next.

Figure 63

33/41

NTB20-095

81.

Erase All DTCs.


Follow the on-screen instructions as shown in Figure 64 and Figure 65.

Figure 64


Select Next.

Figure 65

34/41

NTB20-095

82.

Select Confirm.

XXXXX
XXXXX

XXXXXXXXXXXXXXXX

Figure 66

83.

If the screen in Figure 67 displays, select Home. If the screen in Figure 67 does not
display, skip to step 84 on page 36.

Figure 67

35/41

NTB20-095

Bleed Air & Initialize Oil Deterioration Level

84.

Select Diagnosis (One System).

Figure 68

85.

Select ALL MODE AWD/4WD.

Figure 69

36/41

NTB20-095

86.

Select Work support.


Ensure Can Gateway (CGW Information) is green.

Figure 70

87.

Select BLEED AIR & INITIALIZE OIL DETERIORATION LEVEL.

88.

Select Start.

Figure 71

37/41

NTB20-095

89.

Start the engine and select Start.

Figure 72

90.

Allow BLEED AIR & INITIALIZE OIL DETERIORATION LEVEL to complete.

Figure 73

38/41

NTB20-095

91.

Select End.

Figure 74

92.

Close C-III plus.

93.

Turn the ignition OFF.


94.

It may be necessary to hold the start button in for several seconds for the ignition
to turn OFF.

Disconnect the battery maintainer or smart charger.

39/41

NTB20-095

Recheck AWD Coupler Fluid Level

To prevent serious burns, avoid contact with hot metal parts. Perform the operation after
the exhaust system has fully cooled down because the system will be hot just after engine
stops.
95.

Raise and support vehicle.

96.

Place a drain pan under the AWD coupler filler hole.

97.

Remove the AWD coupler filler plug
using a 10 mm hex socket.

AWD coupler
filler plug

Figure 75

98.

Fill the AWD coupler with fluid.






99.

Only use a dedicated fluid pump
that has not been used for other
types of fluids.
See PARTS INFORMATION for
coupling fluid information.
Fill the AWD coupler until fluid
starts to come out of the filler hole.
Reinstall the filler plug using a new
sealing washer.
Torque the filler plug to 35 N●m
(26 ft-lb).

Fluid pump
Figure 76

Lower the vehicle.

100. Test drive the vehicle including a figure eight to evaluate for any noise and/or vibration
concerns.
 If any noise and/or vibration concerns exist during the figure eight test drive, follow
the All Wheel Drive Coupler Clutch Break-In Procedure in NTB20-081.

40/41

NTB20-095

PARTS INFORMATION
DESCRIPTION
COUPLING ASSEMBLY-ELECTRICAL
(AWD Coupler)
GASKET-PLUG
(Filler Plug Sealing Washer)
COUPLING FLUID (1)
BOLT-FLX PROP (3)
(Propeller Shaft Rear Flange Bolts)
NUT-FIX PROP SFT (3)
(Propeller Shaft Rear Flange Nuts)
(1)

(2)
(3)

PART NUMBER

QUANTITY

38760-6RE0A

1

11026-4N200

1

999MP-LSCTRF

(2)

37120-7S00A

4

37171-7S00A

4

Order this item through the Nissan Maintenance Advantage program: Phone
877-NIS-NMA1 (877-647-6621). Website order via link on the dealer portal;
www.NNAnet.com and click on the “Maintenance Advantage-Tire/Battery/Chemical”
link.
As needed.
These are single use parts.

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
Replace Electronic Control Coupling and
Reprogram ECU
(1)

PFP

OP CODE

SYM

DIA

FRT

(1)

LX11AA

ZE

32

1.7

Reference the electronic parts catalog and use the Electric Coupling Assembly
(38760-*****) as the Primary Failed Part (PFP).

AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
December 22, 2020

NTB20-095

DESCRIPTION
Original bulletin published

41/41

NTB20-095