Ferrari North America
Technical Information

Date:
Bulletin #:
Campaign #:
Supersedes:
Section:

October 2020
2690
10

Model:
Subject: Pre-Delivery Inspection – PDI procedures
Please find enclosed the new procedures and relative list of inspections to be performed at all
times before the vehicle is delivered to the customer.
The following procedures must be performed exactly as indicated and in the order given,
providing the factory with the information requested.

- IMPORTANT This Pre-Delivery Inspection (PDI) procedure may only be performed with a PCTester DEIS updated to at least the following software version (or subsequent
release):
- Module 0

Portal and Troubleshooting

54

- Module 1

DEIS Diagnostic software

91

- Module 2

Technical Documentation

12

- Module 3

Tools

8

Check the software number and, if necessary, update your DEIS Tester
immediately.
After updating the DEIS, the first vehicle diagnostic cycle must be performed
using a cable connection.

© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
Procedure.
1.

Visually inspect condition of vehicle paintwork; repair if necessary (use the specific
“Bodywork defects” form annexed on page 10).

2.

If disconnected, connect the negative pole of the battery and reset the vehicle autoadaptive parameters (as described in paragraph F3.01 of the Workshop Manual).

3.

Activate Key-ON state and check the automatic gearbox mode indicated on the
instrument panel:
- if letter “P” (Park Lock) is displayed, go to point 5.
- if letter “N” (Neutral) is displayed, go to point 4.

4.

Re-enable the Park Lock – Gearbox lock device (as described in paragraph C2.07 of the
Workshop Manual).

5.

Remove the engine compartment cosmetic shields (as described in paragraph E3.03 of
the Workshop Manual), then perform the “Battery Certification” procedure (TI
2079/2230) and compile the relative form. If necessary, remove the battery from the
vehicle and charge using the “SLOW charge ” procedure (TI 2078).

6.

Using the DEIS tester, disable the “Logistic Mode” function with diagnostic cycle “150
Complete Logistic Mode” on the NBC ECU (Body Computer Node).

7.

Test the keys and the anti-theft system.

8.

Check that the daytime lights are working (depending on market).

9.

Check that the low beam lights work correctly: also check that the AHS - Adaptive
Headlights System (if applicable) works correctly when the steering wheel is turned.

10. Check the vehicle front lift (if present) is working: also check that the AHS (low beam
headlamp orientation) system is working correctly. With the car raised, the height of the
headlight beam must be the same as with the car lowered.
11. Check that the high beams work correctly.
12. Check that the brake lights work correctly.
13. Check that the turn indicators and license plate lights work correctly.
2
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2690
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
14. Check that all the cabin lights in the vehicle work correctly.
15. Test the buttons on the steering wheel, dashboard, doors and center console tunnel, and
check that their respective backlights, the ceiling light unit and the USB port socket
backlight work correctly.
16. Test the horn.
17. Check that the power windows work correctly.
18. Check that the windshield and headlight wipers/washers work correctly.
19. Check that the mechanical/electrical steering adjustment mechanism works correctly.
20. Check the electric seat functions: check fore/aft, backrest rake, height and cushion tilt
angle adjustment functions. If applicable, also check the seat memory functions (driver
side only) and the lumbar support, pneumatic side bolster, seat cushion length (upper
leg support) adjustment functions and the heated seat/seat ventilation function.
21. Check that the EPB electric parking brake works correctly; test manual and automatic
modes.
22. Check that Infotainment / navigation system works correctly (if installed, see point 34);
set the relative roadside assistance numbers for your market.
23. Check engine coolant level and top up if necessary.
24. Check the brake fluid level and top up if necessary.
25. Check the headlight washer/windshield washer fluid level and top up if necessary.
26. Check that the TPMS system is calibrated.
27. Check the tightness of the wheel studs with a torque wrench . The tightening torque must
be 120 Nm (as described in paragraph D2.01 of the Workshop Manual).
28. Check that the tow hook can be fitted correctly.

3
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2690
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
Start engine and perform the following:
29. Check that the air conditioning and heating system works correctly (static test).
30. Check that the electric rear view mirrors work correctly.
31. Check that the internal electrochromic mirror and the electrochromic RH and LH rear
view mirrors (if installed) work correctly.
32. Check that the parking sensors, rear and front parking cameras (if applicable) and
Surround View cameras (if applicable) work correctly.
33. Using the DEIS tester, perform the “Cancel all DTCs from all ECUs” procedure from the
“Vehicle functions” menu.
Test drive.
34. Check function of navigation system (if applicable); set route before setting off.
35. Test drive the vehicle (approx. 20 minutes).
36. Check that Stop&Start system works correctly.
37. While driving, check that the “Manettino” dial on the steering wheel works correctly. Also
check that the “Suspension damping decouple” function, selectable by pressing the
Manettino control, works correctly.
38. While driving, check that the ADAS driver assistance systems (if applicable) work
correctly:
•
•
•
•
•

Adaptive Cruise Control;
Blind Spot Detection;
Rear Cross Traffic Alert;
Traffic Sign Recognition;
Lane Departure Warning.

39. While driving, check that the air conditioning and heating system work correctly
(dynamic test).
4
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2690
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
40. For USA/CND Version only. Take the vehicle into a location with a clear view of the sky
and activate Sirius XM as per FNA 165.
Return to workshop.
41. Check the engine oil level (engine warm and switched off) and top up if necessary (as
described in paragraph B8.02 in the Workshop Manual).
42. Using the DEIS tester, check that the VIN number read on the tester matches the number
indicated on the VIN plate located at the bottom left of the windshield and the number
punched onto the chassis of the vehicle. The punched VIN number on the chassis is visible
via an opening in the floorpan carpet on the passenger side. For more information on the
locations of vehicle identification numbers, see chapter A1.02 of the Workshop Manual.
43. Check and cancel the errors on all ECUs.
44. Enter the warranty start date (Check that the language setting on the TFT display is
correct).
45. Perform the “SCAN OUT” procedure from the “Vehicle functions” menu with the DEIS
tester before carrying out any further diagnostic operations.
46. Remove the complete aerodynamic undertray and the cosmetic engine compartment
shields from the vehicle (as described in paragraphs E3.01 and E3.03 of the Workshop
Manual).
47. Visually check for coolant and/or oil leaks in the underbody area and engine
compartment.
48. Visually inspect engine compartment lines.
49. Visually inspect the engine compartment wiring harnesses.
50. Visually inspect underbody lines.
51. Visually inspect exhaust pipe.
52. Visual inspection of fuel tanks.
53. Check visually that the following are fitted correctly: Suspension assembly components,
steering box and axle shaft flanges.
5
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2690
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
54. Check visually that the following are fitted correctly: vehicle earth and engine-chassis
ground.
55. Visually inspect condition of brake pads and discs (DO NOT remove wheels).
56. Check condition of tires and wheels.
57. Refit the complete aerodynamic undertray and cosmetic engine compartment shields (as
described in paragraphs E3.01 and E3.03 of the Workshop Manual).
58. Check that the door and lid locks work correctly; adjust if necessary.
59. Check that the fuel filler flap emergency release works correctly, and adjust if necessary.
60. Visually inspect condition of vehicle interior; repair if necessary.
61. Thoroughly clean interior and wash car.
62. Ensure that the vehicle is delivered complete with the following:
- identification and type approval plates
- number plate holder
- tool kit
- on-board documentation (Owner's Manual, Quick Reference Guide, Warranty
Booklet, Safety Device Booklet and Battery Conditioner Quick Guide card), second
vehicle key and code card, and any material related to options.
63. Check that the battery conditioner provided with the vehicle works correctly, referring to
the relevant manual.

6
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2690
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
- IMPORTANT Confirm that the operations listed above have been carried out correctly with the “Pre-Delivery
Inspection - PDI” form (enclosed on pages 8 and 9), compiled in full and signed by the Aftersales
Manager of your Service Centre.

After the inspection procedures, ALWAYS open an ROL (Red On Line) if the vehicle is in “New
Model/Special Series” status (ref. TI 2667) specifying “PDI Form Info” as the description, and
attach the duly compiled “PDI Pre-Delivery Inspection” form together with the printout files of
the parameters and errors requested in points 5, 33 and 45.

You will also be required to open a separate individual ROL with the description "PDI Fault
Info" for each fault encountered during the inspection procedure, indicating the respective
operation number as cited in the “PDI Pre-Delivery Inspection” form; Attach all necessary
documentation, including photographs if needed.

Thank you for your co-operation.

7
© 2020. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2690
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Model

Updated on
August 2020

Chassis number:

Dossier creation date:

Job order no.:
Notes:
Description of inspection / operation:
1. - Condition of vehicle paintwork.
2. - Connect battery and reset vehicle parameters.
3. - Check Park Lock device.
4. - Reset Park Lock device.
5. - “Battery Certification” procedure.
6. - Disable “Logistic Mode”.
7. - Test the keys and the anti-theft system.
8. - Daytime running lights.
9. - Low beam lights and AHS (if applicable).
10. - Check the front vehicle lift (if installed).
11. - High beams.
12. - Stop lights.
13. - Turn indicators and license plate lights.
14. - Check that the interior light units work correctly.
15. - Test the buttons and check that backlighting works
correctly.
16. - Horn.
17. - Power windows.
18. - Windshield and headlight wipers.
19. - Steering wheel adjustment.
20. - Check seat functions.
21. - Electric parking brake (EPB); manual/auto.
22. - Infotainment / Navigation system (if applicable)
(see point 34).
23. - Engine coolant level.
24. - Braking system fluid level.
25. - Windshield washer/headlight washer fluid level.
26. - Tire pressure calibrated with TPMS.
27. - Tightening of wheel stud bolts.
28. - Tow hook.
29. - * Air conditioning and heating system (static test).
30. - * Electric rear-view mirrors.
31. - * Electrochromic rear view mirrors (if applicable).
32. - * Parking sensors, front/rear cameras and Surround View.
33. - Cancel all DTCs from all ECUs.
34. - Navigation (if applicable): Set route.
35. - Test drive (20 min.).
36. - Test Stop&Start function.
(*) With engine running

Te chnical Service De partment
Page 8 of 10

Performed Performed
OK
NOT OK
















































































R.O.L. N°
(if NOT OK)

Pre-Delivery Inspection - PDI form

Page 02 of 02

Model

Updated on
August 2020

37. - “Manettino” and suspension damping decouple function.
38. - Check ADAS systems (if applicable).
39. - Air conditioning and heating system (dynamic test).
40. - For USA / CND ONLY _ SiriusXM activation.
41. - Engine oil level (engine warm – off).
42. - Check VIN on NCM, on windshield VIN plate and on chassis.
43. - Check and cancel ECU errors.
44. - Enter warranty start date.
45. - Perform “SCAN OUT” procedure.
46. - Remove complete aerodynamic undertray and shields.
47. - Water and/or oil leaks in vehicle underbody .
48. - Engine compartment lines.
49. - Engine compartment wiring.
50. - Underbody lines.
51. - Exhaust pipe.
52. - Visual inspection of fuel tanks.
53. - Visual inspection: Suspension components, etc.
54. - Visual inspection of earth connections: vehicle and enginechassis ground.
55. - Condition of brake pads and discs (DO NOT remove
wheels).
56. - Condition of tires and wheel rims.
57. - Refit flat undertray and engine compartment shields.
58. - Door and lid locks.
59. - Fuel filler flap emergency opening.
60. - Condition of vehicle interior.
61. - Clean interior and wash car.
62. - Material provided with vehicle: Identification plates,
toolkit, etc.
63. - Functional test of battery conditioner



































































Job performed by (Dealer):
Technical Manager:
First name

Last Name
(Print

(Print)

Company stamp

Full signature
Vehicle delivery date:
Te chnical Service De partment
Page 9 of 10

Issue

Te chnical Service De partment
Page 10 of 10