10/5/2020

34 07 20_SERVICE ACTION: REPLACE HYDRAULIC UNIT, DYNAMIC STABILITY CONTROL INTEGRATED (DS

SIB 34 07 20
2020-09-01
SERVICE ACTION: REPLACE HYDRAULIC UNIT, DYNAMIC STABILITY
CONTROL INTEGRATED (DS

MODEL
F95 (X5 M Sports
Activity Vehicle )
G07 (X7 Sports
Activity Vehicle)

F96 (X6 M Sports
Activity Coupe)

G05 (X5 Sports
Activity Vehicle)

G06 (X6 Sports
Activity Coupe)

Please perform the procedure outlined in this Service Information on all affected vehicles before customer
delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure
the next time the vehicle is in the shop.

AFFECTED VEHICLES
Affected vehicles which require this Campaign to be completed will show it as “Open” when checked either
in AIR, the “Service Menu" of DCSnet (Dealer Communication System), ISPA NEXT or Warranty Vehicle
Inquiry.

SITUATION
DSCi units which potentially have a faulty hydraulic valve were installed in the vehicles. The affected units
may activate a sporadic red-colored Check Control Message.

CAUSE
Manufacturing error of the DSCi hydraulic unit.

CORRECTION
Replace the DSCi hydraulic unit.

PROCEDURE
Replace the DSCi as per the REP 34 51 601 Replacing hydraulic unit.
Program the vehicle using the latest version of ISTA; e.g., 4.25.1x released late August 2020.
Note that ISTA will automatically reprogram and code all programmable control modules that do not have
the latest software.

PARTS INFORMATION
Only use and invoice the part numbers below.
Performing a part number look-up in ETK (EPC) by VIN or model in place of using/invoicing the
following part numbers may result with the wrong part numbers being invoiced and installed, this
could delay the payment of the claim.
Part Number
34 51 5 A05 D20
07 11 9 904 295
34 33 6 864 115
81 22 0 142 156

Description
DSCi (Power brake)
Self-locking flanged nut
Brake force amplifier seal
Brake fluid (12oz btl.)

Quantity
1
2
1
Sublet as needed

WARRANTY INFORMATION
Copyright ©2020 BMW of North America, Inc.
1/3

10/5/2020

34 07 20_SERVICE ACTION: REPLACE HYDRAULIC UNIT, DYNAMIC STABILITY CONTROL INTEGRATED (DS

During this workshop visit, the affected vehicle may also show one or more programming and encoding
Technical Campaign repairs open, the programming and encoding procedure may only be invoiced one
time.
After replacing the DSCi to perform this Service Action, select one of these open Technical
Campaigns to perform and submit for updating the vehicle to the required I-level or higher (If
stated).
Please be sure to also perform any additional work (before and/or after) the selected campaign or
other campaign repairs require and/or close the remaining open programming and encoding
Technical Campaign repairs as outlined in the corresponding Service Information Bulletin.
Reimbursement for this Recall will be via normal claim entry utilizing the applicable work package
information below and the part numbers listed above:
Defect Code:

0034480200

G05 G06 G07 F95 F96 Replace hydraulic unit, DSCi

Completion before the first vehicle delivery to a customer or the vehicle is already in the workshopWork Pkg
#1

Labor Operation Description (Plus work)
Labor Allowance
Replacing the DSCi, programming and
encoding control units (includes connecting
00 69 751
26 FRU
an approved battery charger/power supply
and performing a vehicle test)

Or:

#2

00 69 752

Replacing the DSCi,
programming/encoding vehicle control units
was performed in conjunction with another 18 FRU
campaign or repair during the same
workshop visit

Or:
The vehicle arrives at your center and this Action shows open (No other main work will be
performed or claimed during this workshop visit)Work Pkg

#3

Labor Operation Description (Main work)

00 69 225

Labor
Allowance

Replacing the DSCi, programming and
encoding control units (includes connecting
28 FRU
an approved battery charger/power supply
and performing a vehicle test)

Only one of the flat rate labor operation codes listed above can be used for claim
submission/reimbursement purposes. Also, only one Main work flat rate labor operation code can be
claimed per workshop visit.
Claim Repair Comments
Only reference the SIB number and the work package (Pkg) number performed in the RO technician notes
and the claim comments (For example: B34 07 20 WP 1), unless otherwise required by State law.
And, as needed:

Copyright ©2020 BMW of North America, Inc.
2/3

10/5/2020

34 07 20_SERVICE ACTION: REPLACE HYDRAULIC UNIT, DYNAMIC STABILITY CONTROL INTEGRATED (DS

Sublet – Bulk Materials (RO and Claim Comments Required)
Sublet Code
4

Up to $20.00

Reimbursement for the repair-related bulk material (Do not use
the BMW part number for claim submission)

Sublet reimbursement calculation for claiming the applicable repair-related bulk materials (BMW part
number) is at the dealer net price amount for the quantity used plus your center’s handling.
Enter this material cost in sublet and itemize the amount on the repair order and in claim comment section.
And, as applicable:
Alternative Mobility Solution (AMS) for Vehicle Owners (RO and Claim Comments Required)
This Service Action repair qualifies for Alternative Mobility Solution (AMS) expense reimbursement, claim
this item under the Defect Code noted above as follows:
Sublet Code 2 - Itemize the AMS sublet amount on the repair order and in the claim comment section.
Please refer to SI B01 29 16 for additional information.

Programming and Encoding - Vehicle Control Units (RO and Claim Comments Required)
The programming procedure automatically reprograms and encodes all vehicle control modules which do
not have the latest software I-level. If one or more control module failures occur during this programming
procedure:
Please claim this consequential control module-related IRAP recovery procedure (when applicable
as required)/repair work under the defect code listed in this bulletin with the applicable AIR labor
operations.

Please explain this additional work (The why and what) on the repair order and in the claim comments
section
For control module failures that occurred prior to performing this programming procedure:
When covered under an applicable limited warranty, claim the applicable test plan and the
corresponding control module-related repair work using the applicable defect code and labor operations
in AIR (including diagnosis with separate punch times).

As applicable to your center, please refer to SI B01 01 20 or B01 07 20 for your diagnosis work time
claiming and explanation procedures.

QUESTIONS REGARDING THIS BULLETIN
Technical inquiries
Warranty inquiries
Parts inquiries

Submit feedback at the top of this bulletin
Submit an IDS ticket to the Warranty Department
Submit an IDS ticket to the Parts Department

Powered by Froala Editor

Copyright ©2020 BMW of North America, Inc.
3/3