Revisions to this document are noted
by a stripe in the left-hand margin

SUBJECT:

2019FA07, Rev. E
September 16, 2020
Product Code(s): 65, 66
Page 1 of 15

Special Coverage for TIDB Aluminum Main Valve Body – Reactive

MODELS AFFECTED:

3000 Series™, 4000 Series™, B200™, B300™, B3400 xFE™, B400™, B500™, T200™,
T300™, T400™, T500™ Models

VOCATIONS AFFECTED:

All Vocations

Introduction:
Allison Transmission, Inc. has identified a potential concern with the TIDB Aluminum Main Valve Body. As a
Global Customer Satisfaction initiative, Allison Transmission, Inc. will support the reactive repair of units with
symptoms attributable to the subject part in the serial number ranges identified in Table 1 for five years from
the in-service date of the vehicle. This Field Action does not cover transmission service work unrelated to the
symptoms described within.
NOTE: The purpose of this Field Action is to provide a reactive repair (after a failure has occurred)
of the covered condition. Refer to the following instructions to identify affected transmissions, obtain
authorization to perform the repair, and submit the proper warranty claim.
The following symptoms may be present with a suspect TIDB Main Valve Body:
• Harsh upshifts when C2 clutch is oncoming (6 speed: 3-4 upshift, 7 speed: 3-4 or 4-5 upshift)
• Premature P088A Transmission Filter Maintenance Alert, and/or P088B Transmission Filter Maintenance
Required DTCs
• Premature P2789 Transmission Clutch Life Expired (Clutch Adaptive Learning at Limit) DTC
• Premature TRANSHEALTH Transmission Health Monitor failure
Table 1. Affected Serial Number Range, Models and Vocations
Global Customer
Satisfaction Initiative
TIDB Main Valve Body

Product Code

Affected Serial Number
(S/N) Range

Affected Transmission Models

Affected Vocations

Starts with S/N 651

6511516207 6511680891

3000 Series™, B200™, B300™,
B400™, T200™, T300™

All

MC / FA8624EN

5251007

Copyright © 2020 Allison Transmission, Inc. All Rights Reserved.

2019FA07, Rev. E
September 16, 2020
Product Code(s): 65, 66
Page 2 of 15
Table 1. Affected Serial Number Range, Models and Vocations (cont'd)
Global Customer
Satisfaction Initiative
TIDB Main Valve Body

Product Code

Affected Serial Number
(S/N) Range

Affected Transmission Models

Affected Vocations

Starts with S/N 651

6511516236 6511687928

3700

All

Starts with S/N 652

6520201013 6520222681

3000 Series™, B300™,
T200™, T300™

All

Starts with S/N 661

6610507871 6610578390

4000 Series™, B500™, T400™

All

Starts with S/N 661

6610507990 6610582232

4700/4800

All

Starts with S/N 662

6620030644 6620036700

4000 Series™, B500™, T500™

All

Starts with S/N 662

6620030654 6620036956

4700/4800

All

NOTE: There are a small number of trial run transmissions within the affected serial number ranges
assembled with anodized TIDB main valve bodies in the factory or converted to TIDA in the field. Those
serial numbers are ineligible for this Field Action. The Field Action Authorization Tool will not return an
authorization number for those units.

NOTE: Anodize implementation dates for 6-speed and 7-speed models were not simultaneous. As a
result, eligible serial number ranges between those models differ.

Vehicle Configuration Category - Service Plan:
Determine classification of vehicle based upon Table 2.
Table 2. Vehicle Classification
Vehicle State

Classification

6-Speed - Upon Arrival - Prognostics Enabled

Category 1

6-Speed - Upon Arrival - Prognostics Disabled

Category 2

6-Speed - Upon Arrival - Prognostics Disabled then Enabled
at Customer Request

Category 1

7-Speed (no Filter Life Body Present)

Category 2

Category 1 Service Action:
Install anodized Main Valve Body, current configuration Main Regulator Valve, current configuration Filter Life
Indicator Spring, and reflash TCM to software level C191 or later if pre-C191 present. If C191 or later software level
is present, force Fast Adapt using Clear All Shift Adaptive Data command in Allison DOC® Action Request.

Copyright © 2020 Allison Transmission, Inc. All Rights Reserved.

2019FA07, Rev. E
September 16, 2020
Product Code(s): 65, 66
Page 3 of 15
NOTE: Some OEMs are on Flexible Release Timing (FRT) and, as a result, are held at a specific software
level. If the attempt to reflash the TCM to C191 or later software level is unsuccessful, FRT may be
applicable to the OEM. If this occurs, force Fast Adapt using Clear All Shift Adaptive Data command in
Allison DOC® Action Request.

Category 2 Service Action:
Install anodized Main Valve Body, current configuration Main Regulator Valve, and force Fast Adapt using Clear All
Shift Adaptive Data command in Allison DOC® Action Request.
NOTE: Prior to performing work, please read SIL 22-WT-19, SIL 23-WT-19, and SIL 27-WT-19 related to
the 3000/4000 Series TIDB Aluminum Main Valve Body and Main Regulator Valve.

Field Action Transmission Identification:
Prior to the repair of a suspect transmission, verify that the Field Action repair has NOT already been performed.
Login to https://sap.allisontransmission.com/extranet/fieldactions. Enter the transmission serial number, vehicle
vocation code, and request an authorization. If you receive an authorization number, then this is confirmation that
the Field Action has NOT been performed. If the Field Action has NOT been performed, proceed with the repair.
Include the authorization number in the warranty claim narrative prior to submitting the claim. If you are unable
to obtain an authorization number, and you believe the transmission qualifies for the Field Action based on the
serial number range, contact the Allison Technical Assistance Center (TAC) at 1-800-252-5283 or 317-242-0700 or
E-mail: Allison[email protected].

Allison Service Outlet Field Action Responsibility:
When a Customer has a vehicle in the affected S/N range that displays the symptoms previously listed, the service
outlet shall take the following steps to support the customer:
1. Confirm the transmission is within the affected S/N range per Table 1.
2. Verify the transmission nameplate does not have the “X” Identification Mark indicating Field Action service
work has already been performed (refer to Figure 3).
3. Request a 2019FA07 authorization number for the transmission serial number to be repaired.
4. For six-speed models, determine whether Prognostics are enabled or disabled.
• If, when keying-on the vehicle, the wrench indicator illuminates, Prognostics are enabled.
• Not all vehicles with Prognostics enabled will display the wrench icon at key-on. The icon is disabled at
key-on in some calibrations.
• Table 3 may be used to determine if Prognostics are enabled using the shift selector.
• Allison DOC® may also be used to determine if Prognostics are enabled.

Copyright © 2020 Allison Transmission, Inc. All Rights Reserved.

2019FA07, Rev. E
September 16, 2020
Product Code(s): 65, 66
Page 4 of 15
Table 3. Shift Selector Function
Pushbutton Shift Selector - Press Up & Down Arrows Simultaneously
Bump Lever Shift Selector - Press Diagnostics Button (Allison Logo) Once
Button Press Count (Bold Indicates Prognostics Function)
3000/4000 Series
Configuration

1

2

3

4

5

With Prognostics With Oil
Level Sensor

Fluid Level

Oil Life

Filter Life

Trans Health

Diagnostics

With Prognostics Without Oil
Level Sensor

Oil Life

Filter Life

Trans Health

Diagnostics

Without Prognostics With Oil
Level Sensor

Fluid Level

Diagnostics

Without Prognostics Without
Oil Level Sensor

Diagnostics

5. Verify the required service parts shown in Table 4, Table 5, Table 6, Table 7, Table 8, or Table 9 are in
inventory to support the service work.
• Use Table 4 to support a Product Code 65 3000 Series™ 6-speed unit in a Category 1 vehicle.
• Use Table 5 to support a Product Code 65 3000 Series™ 6-speed unit in a Category 2 vehicle.
• Use Table 6 to support a Product Code 65 3000 Series™ 7-speed unit in a Category 2 vehicle.
• Use Table 7 to support a Product Code 66 4000 Series™ 6-speed unit in a Category 1 vehicle.
• Use Table 8 to support a Product Code 66 4000 Series™ 6-speed unit in a Category 2 vehicle.
• Use Table 9 to support a Product Code 66 4000 Series™ 7-speed unit in a Category 2 vehicle.
6. Replace parts listed in Table 4, Table 5, Table 6, Table 7, Table 8, or Table 9 per the Service Manual SM4013
or SM4014 Control Module Overhaul procedures.
NOTE: Prior to re-using the PS1 Switch Assembly or PS2 Switch Assembly, closely inspect the O-ring of
each switch for damage. If either O-ring is questionable, replace the part.

NOTE: Closely inspect the Main Regulator Valve P/N 29563501 for the presence of a manufacturing burr
shown in Figure 1 and Figure 2 below. See SIL 01-WT-20 for additional clarification.

Figure 1.

Copyright © 2020 Allison Transmission, Inc. All Rights Reserved.

2019FA07, Rev. E
September 16, 2020
Product Code(s): 65, 66
Page 5 of 15

Figure 2.
7. In vehicles with six-speed transmissions and Prognostics enabled (Category 1), if the software level is prior
to C191, reflash the TCM to C191 or later software level. If C191 or later software level is already present,
force Fast Adapt using Clear All Shift Adaptive Data command in Allison DOC® Action Request.
8. In vehicles with six-speed transmissions and Prognostics disabled (Category 2), or in vehicles with
seven-speed transmissions (Category 2), use the Allison DOC® Action Request command Clear All Shift
Adaptive Data to force Fast Adapted shifts. There is no need to reflash the TCM to C191 or later software
level in these vehicles.
NOTE: The Clear All Shift Adaptive Data Action Request forces the TCM to use the Fast Adaptive
algorithm to adapt shifts.
9. Fill transmission with the same type of fluid that was drained. Reset Fluid Life Monitor as-required.
10. Stamp or etch an “X” identification mark into the transmission nameplate in the location shown in Figure 3.

Copyright © 2020 Allison Transmission, Inc. All Rights Reserved.

2019FA07, Rev. E
September 16, 2020
Product Code(s): 65, 66
Page 6 of 15

Figure 3. Identification Mark
11. File AWAARE claim per Table 10, Table 11, Table 12, Table 13, Table 14, Table 15, or Table 16.

Required Service Parts:
The following tables provide the required service parts for this Global Customer Satisfaction Field Action 2019FA07
initiative.
Table 4. Product Code 65 – 3000 Series™, B200™, B300™, B400™, T200™, T300™ Models – Category 1
Mandatory/AsRequired

Part Number

Part Name

Quantity

Mandatory

23019664

Drain Plug O-ring

1

Mandatory

23046376

Seal, Face

3

Mandatory

29503283

Gasket, Case

1

Mandatory

29503382

O-ring, 14.0 mm ID

1

Mandatory

29503384

O-ring, 18.8 mm ID

1

Mandatory

29507437

Filter Cover O-ring

2

Mandatory

29512863

O-ring, Standoff, 47.2 mm ID

1

Mandatory

29524449

Filter Cover Gasket

2

Mandatory

29535518

O-ring, 13.0 mm ID

6

Mandatory

29537066

Gasket, Suction Filter

1

Mandatory

29542976

O-ring, 10.5 mm ID

6

Mandatory

29542991

Seal, Face

1

Mandatory

29548953

Filter Cover O-ring

2

As-Required

29549658

Switch Assembly, Pressure (PS2)

1

As-Required

29552364

Switch Assembly, Pressure (PS1)

1

Mandatory

29557154

Body, Main Control Valve

1

Mandatory

29557345

Gasket, Channel Plate

1

Mandatory

29562588

FLI Spring

1

Mandatory

29563501

Valve, Main Regulator

1

Copyright © 2020 Allison Transmission, Inc. All Rights Reserved.

2019FA07, Rev. E
September 16, 2020
Product Code(s): 65, 66
Page 7 of 15
Table 5. Product Code 65 – 3000 Series™, B200™, B300™, B400™, T200™, T300™ Models – Category 2
Mandatory/AsRequired

Part Number

Part Name

Quantity

Mandatory

23019664

Drain Plug O-ring

1

Mandatory

23046376

Seal, Face

3

Mandatory

29503283

Gasket, Case

1

Mandatory

29503382

O-ring, 14.0 mm ID

1

Mandatory

29503384

O-ring, 18.8 mm ID

1