Ferrari North America
Technical Information

Date:
Bulletin #:
Campaign #:
Supersedes:
Section:

August 2020
2680
2436
10

Subject: 812 Superfast P re-Delivery Inspection – PDI procedures
This Technical Information Cancels and Replaces
the previous TI 2436 of June 2017

Please find enclosed the procedures and list of inspections to be performed at all times before
the vehicle is delivered to the customer.
The following procedures must be performed exactly as indicated and in the order given,
providing the factory with the information requested.

- IMPORTANT This Pre-Delivery Inspection (PDI) procedure may only be performed with a PCTester DEIS updated to at least the following software version (or subsequent
release):
- Module 0

Portal and Troubleshooting

47

- Module 1

DEIS Diagnostic software

- Module 2

Technical Documentation

12

- Module 3

Tools

7

76

Check the software number and, if necessary, update your DEIS Tester
immediately.
After updating the DEIS, the first vehicle diagnostic cycle must be performed
using a cable connection.

© 2020 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
Procedure.
1.

Visually inspect condition of vehicle paintwork; repair if necessary (use the specific
“Bodywork anomalies” form annexed on page 10).

2.

If disconnected, connect the negative pole of the battery and reset the vehicle
auto-adaptive parameters (as described in paragraph F2.01 of the Workshop Manual).

3.

Activate Key-ON state (as described in paragraph E5.06 of the Workshop Manual), and
check which letter is shown on the DOT MATRIX display:
- If letter “P” (Park Lock) is on the display, go to point 5.
- If letter “N” (Neutral) is on the display, go to point 4.

4.

Re-enable the Park Lock – Gearbox lock device (as described in paragraph E5.10 of the
Workshop Manual).

5.

Remove the engine compartment cosmetic shields (as described in paragraph E3.14 of
the Workshop Manual); Perform the “Battery Certification” procedure (TI 2079 /
2230), and compile the relative form. If necessary, remove the battery from the vehicle
and charge using the “SLOW charge” procedure (TI 2078).

6.

Using the DEIS tester, disable the “Logistic Mode” function with diagnostic cycle “150
Complete Logistic Mode” on the NBC ECU (Body Computer Node).

7.

Test the keys and the anti-theft system.

8.

Check that the daytime lights work correctly (depending on market).

9.

Check that the low beam lights work correctly: also check that the AHS system (Adaptive
Headlights System - if applicable) works correctly by turning the steering wheel.

10. Check the vehicle front lift (if present) is working: also check that the AHS system
(Adaptive Headlights System - if applicable) works correctly. With the
car raised, the height of the headlight beam must be the same as with the car lowered.
11. Check that the high beam lights work correctly.
12. Check that the brake lights work correctly.
2
© 2020 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2680
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
13. Check that the turn indicators and license plate lights work correctly.
14. Check that the steering wheel buttons, door lights, vehicle interior lights, footwell lights,
luggage compartment lights and rear lid lights work correctly.
15. Test the buttons on the steering wheel, dashboard, doors and center console tunnel, and
check that their respective backlights, the ceiling light unit and the USB port socket
backlight work correctly.
16. Test the horn.
17. Check that the power windows work correctly.
18. Check that the windshield and headlight wipers/washers work correctly.
19. Check that the steering adjustment mechanism works correctly.
20. Check that the driver and passenger side electric or mechanically adjusted seats work
correctly and test the memory storage function.
21. Make that the electric parking brake (EPB) works correctly; test manual and automatic
modes.
22. Check that Hi-Fi / navigation system works correctly (see point 34); set the relative
roadside assistance numbers for your market.
23. Check coolant level and top up if necessary.
24. Check brake fluid level and top up if necessary.
25. Check headlight washer/windshield washer fluid level and top up if necessary.
26. Check tire pressure/calibration with TPMS.
27. Check tightening of wheel stud bolts using a torque wrench (as described in paragraph
D2.01 in the Workshop Manual).
28. Check that the tow hook is fitted correctly.
3
© 2020 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2680
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
Start the engine (as described in paragraph E5.06 of the Workshop Manual), and
perform the following:
29. Check that the air conditioning and heating system works correctly (static test).
30. Check that the electric rear-view mirrors work correctly.
31. Select reverse:
- check that the angle of the RH rear view mirror(or the LH mirror on RHD
cars) adjusts automatically;
- check that the internal electrochromic mirror and the electrochromic RH
and LH rear view mirrors work correctly.
32. Check that the front and rear parking sensors work correctly; check the rear and front
cameras (if present).
33. Using the DEIS tester, perform the “Cancel all DTCs from all ECUs” procedure from
the “Vehicle functions” menu.
Test drive.
34. Check that the navigation system works correctly (if applicable); Set route before starting.
35. Test drive the vehicle (approx. 20 minutes).
36. Check that Stop&Start system works correctly.
37. While driving, check that the “Suspension damping decoupling” button and
“Manettino” dial on the steering wheel work correctly.
38. While driving, check that the ADAS
correctly:
- Adaptive Cruise Control;
- Blind Spot Detection;
- Rear Cross Traffic Alert;
- Traffic Sign Recognition;
- Lane Departure Warning;

driver assistance systems (if applicable) work

4
© 2020 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2680
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
39. While driving, check that the air conditioning and heating system works correctly
(dynamic test).
40. For USA/CND Version only. Take the vehicle into a location with a clear view of the sky
and activate Sirius XM as per FNA 165.
Return to workshop.
41. Check the engine oil level (engine warm and at idle speed) and top up if necessary (as
described in paragraph A3.01 of the Workshop Manual).
42. With the DEIS tester, check that the VIN number read with the tester matches the VIN
number of the vehicle; if necessary, the VIN number read with the tester may be modified
using the “100 VIN Writing” diagnostic function (password-protected) on the NCM
ECUs (RH and LH engine control nodes).
43. Check and cancel the errors on all ECUs.
44. Enter the warranty start date (Check that the language setting on the TFT display is
correct).
45. Disconnect the battery , wait 30” and reconnect (as described in paragraph F2.01 of the
Workshop Manual). Restore the self-adaptive vehicle parameters (as described in
paragraph F2.01 of the Workshop Manual).
46. Perform the “SCAN OUT” procedure from the “Vehicle functions” menu with the DEIS
tester before carrying out any further diagnostic operations.
47. Remove the aerodynamic undertray from the vehicle (as described in paragraph E3.13
of the Workshop Manual).
48. Visually check if there are any coolant and/or oil leaks in the underbody and engine
compartment.
49. Visually inspect engine compartment lines.
50. Visually inspect the engine compartment wiring harnesses.
5
© 2020 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2680
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
51. Visually inspect underbody lines.
52. Visually inspect exhaust pipe.
53. Visually inspect fuel tank.
54. Visually check correct assembly of: Suspension units, steering box and rear axle shaft
flanges.
55. Visually check correct assembly of: Vehicle ground point, engine ground point on chassis
and gearbox ground point on chassis.
56. Visually inspect condition of brake pads and discs (DO NOT remove wheels).
57. Check condition of tires and wheels.
58. Refit complete aerodynamic undertray complete and cosmetic engine compartment
shields (as described in paragraph E3.13 and E3.14 of the Workshop Manual).
59. Check that the door and lid locks work correctly; adjust if necessary.
60. Check that the fuel filler flap emergency release works correctly; adjust if necessary.
61. Visually inspect condition of leather upholstery; repair if necessary
62. Thoroughly clean interior and wash car.
63. Ensure that the vehicle is delivered complete with the following:
Identification and Type Approval plates
Number plate holder
Tool kit
on-board documentation (Owner's Manual, Quick Reference Guide, Warranty
Booklet, Safety Device Booklet and Battery Conditioner Quick Guide card), second
vehicle key and Code Card, and any material related to options.
64. Check that the battery conditioner provided with the vehicle works correctly, reffering to
the relative manual

6
© 2020 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2680
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Ferrari North America
- IMPORTANT Confirm that the operations listed above have been carried out correctly
with the “Pre-Delivery Inspection - PDI” form (enclosed on pages 8 and 9),
compiled in full and signed by the Aftersales Manager of your Authorized
Ferrari Dealer.

After the inspection procedures, ALWAYS open an ROL (Red On Line) if
the vehicle is in “New Model/Special Series” status (ref. TI 2667) specifying
“PDI Form Info” as the description. Attach the completed “PDI Pre-Delivery
Inspection” form together with the printout files of the parameters and
errors requested in points 5 , 33, and 46.

You will also be required to open a separate individual ROL with the
description “PDI Fault Info” for each fault encountered during the
inspection procedure, indicating the respective operation number as cited
in the “PDI Pre-Delivery Inspection” form; Attach all necessary
documentation, including photographs if needed.

Thank you for your co-operation.

7
© 2020 Ferrari North America, Inc.
Technical Department
www.ferrariusa.com

TI-2680
All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA

Pre-Delivery Inspection - PDI form

Page 01 of 02

Model

Updated on
May 2020

Chassis number:

Dossier creation date:

Job order no.:
Notes:

Description of inspection / operation:
1. - Condition of vehicle paintwork.
2. - Connect battery and reset vehicle parameters.
3. - Check Park Lock device.
4. - Reset Park Lock device.
5. - “Battery Certification” procedure.
6. - Disable “Logistic Mode”.
7. - Test the keys and the anti-theft system.
8. - Daytime running lights.
9. - Low beam lights and AHS (if applicable).
10. - Check vehicle front lift system (if applicable).
11. - High beams.
12. - Stop lights.
13. - Turn indicators and license plate lights.
14. - Door, vehicle interior and luggage compartment lights.
15. - Function of buttons and backlighting.
16. - Horn.
17. - Power windows.
18. - Windshield wipers and headlight washers.
19. - Steering wheel adjustment.
20. - Check seat functions.
21. - Electric parking brake (EPB); manual/auto.
22. - Hi-Fi system / navigation system (see point 34).
23. - Coolant level.
24. - Brake fluid level.
25. - Windshield washer/headlight washer fluid level.
26. - Tire pressure / TPMS system calibration.
27. - Tightness of wheel studs.
28. - Tow hook.
29. - * AC system (static test).
30. - * Electric rear-view mirrors.
31. - * Electrochromic rear view mirrors (if applicable).
32. - * Parking sensors, front/rear cameras and Surround View.
33. - Cancel all DTCs from all ECUs.
34. - Navigation system: Set route.
35. - Test drive (20 min.).
36. - Test Stop&Start function.
(*) With engine running

Te chnical Service De partment
Page 8 of 10

Performed Performed
OK
NOT OK










































































R.O.L. N°
(if NOT OK)

Pre-Delivery Inspection - PDI form

Page 02 of 02

Model

Updated on
May 2020
Performed Performed
OK
NOT OK

Description of inspection / operation:
37. - Suspension damping decouple button and “Manettino”.
38. - Check ADAS systems (if applicable).
39. - AC system (dynamic test).
40. - For USA / CND ONLY – Sirius XM activation.
41. - Engine oil level (warm engine – at idle speed).
42. - Check VIN on NCM, on windshield VIN plate and on chassis.
43. - Delete ECU errors.
44. - Enter the warranty start date.
45. - Disconnect and reconnect battery.
46. - Perform SCAN OUT procedure.
47. - Remove complete aerodynamic undertray.
48. - Check for water and/or oil leaks in vehicle underbody area.
49. - Engine compartment lines.
50. - Engine compartment wiring.
51. - Underbody lines.
52. - Exhaust pipe.
53. - Fuel tank.
54. - Visual inspection: Suspension components, etc.
55. - Visual inspection of earth connections: vehicle/engine and
gearbox ground on chassis.
56. - Condition of brake pads and discs (DO NOT remove wheels).
57. - Condition of tires and wheels.
58. - Refit flat undertray and the cosmetic engine compartment shields.
59. - Door and lid locks.
60. - Fuel filler flap emergency opening.
61. - Condition of vehicle's leather upholstery.
62. - Clean interior and wash car.
63. - Material provided with vehicle: Toolkit, etc.
64. - Functional test of battery maintainer































































Job performed by (Dealer):
Technical Manager:
First name

Last Name
(Print)

(Print)

Company stamp

Full signature
Vehicle delivery date:
Te chnical Service De partment
Page 9 of 10

R.O.L. N°
(if NOT OK)

Anomalies

Te chnical Service De partment
Page 10 of 10