NHTSA ID Number: 10180144
Manufacturer Communication Number: A9120112037809_7
TSB/Document Date: 2020-10-06
Summary
This informational bulletin contains instructions about updating the navigation map.
91 MIB: MMI navigation map update "How-to guide" - potential customer concerns
91 20 11 2037809/7 September 3, 2020. Supersedes Technical Service Bulletin Group 91 number 20-72 dated
June 3, 2020 for reasons listed below.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
All
2014 - 2021
All
MIB1, MIB2, MIB2+, and MIB3
Condition
REVISION HISTORY
Revision
Date
Purpose
7
-
Revised Technical Background (Added Tip)
Revised Service (Added Tip for activation and updated steps)
6
06/04/2020
Revised title
Revised Technical Background (Updated content)
Revised Service (Removed myAudi download steps)
5
12/20/2019
Revised Condition (Updated website link)
Revised Technical Background (Updated content)
The customer states of one of the following concerns:
The navigation map does not show the latest roads or points of interest.
The map download provided by the myAudi website (www.audiusa.com/myAudi) cannot be performed.
The customer does not know how to obtain the data or cannot perform the update after downloading the data.
The MMI is slow to respond or freezes during the map update.
For vehicles with MIB2, the MMI over-the-air (OTA) map update does not allow for a full map update and
shows greyed-out regions.
The customer is concerned that the OTA map update will consume too much data from the Audi
connect data
subscription.
Page 1 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Technical Background
The new MIB navigation system is the first system that allows the customer to update the vehicle’s navigation
system on their own. The map update is only available in the MMI via an OTA update (as of March 2020). For
the 2015-2016 Audi A3 with MIB1, there is no OTA option in the MMI. Thus the map data can only be updated
using the SD card method (see attachment “MIB Map Update Strategy.pdf”).
Note:
The full navigation map data was available on the myAudi website (www.audiusa.com/myAudi) for download
before March 2020. The myAudi site was turned off in preparation for the myAudi 2.0 website. The new myAudi
2.0 website will be deployed in Q2 2021. Until this time, there will be no solution for the customer to download
the data on their own. The full navigation map data will only be possible by the service department. The service
department will need to order the service part by ordering the appropriate SD card (see TSB 2044694 titled, “91
MMI navigation database concerns (Missing traffic info, Incorrect speed limits, Missing streets; POI not listed,
etc.).”
For MIB1 & MIB2 vehicles, map updates are free for the first 2½ years after the production date of the vehicle.
The vehicle is automatically activated from the factory to allow the customer to update the MMI navigation with
the next five releases within the next 2½ years. This means the customer can attempt to update the MMI with
the same release as many times as they want. Release schedules for map updates are approximately CW22
and CW45 of each year.
The customer can update the MMI as many times as they like during the current release period. For instance, if
the customer decides to perform the partial update via the Over-the-Air method in the MMI, then the customer
can decide later to perform the complete update using the same map data for the current release for free. This
only counts as a single update since the update data is from the same release. The five updates are related to
the release schedules and not the attempts the user makes to update the MMI.
Once the period of 2½ years after the vehicle’s production date has passed, map updates will no longer work in
the MMI. The last available update for the customer’s car will always remain available for download via the
myAudi portal (after Q2 2021).
MIB1 & MIB2 Customers (not available for MIB2+ & MIB3) will be able to purchase activations via Audi
accessories to allow the MMI to be updated to the latest map update. This activation will allow the current
release and the forthcoming next release to be available to the customer (see attachment “MIB Map Update
Strategy.pdf”). Please talk to your parts department to find out which activations are available for purchase by
the customer. The dealer can purchase the map data on an SD card.
Tip: Map activations should always be performed before updating the map data. Doing so will ensure the
navigation system is always available, and the correct map data is installed. DO NOT install the map data via
the red engineering menu of the MMI until AFTER the map activation is performed via ODIS >> Flash.
The customer must NEVER be charged for the map data on the SD card. The dealer should consider this as a
shop tool and purchase it for the service department to use. This map data from the parts department can only
Page 2 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
be installed using the RED ENGINEERING MENU of the MMI. The customer only purchases the activation
documentation to enable the map installation (see TSB 2044694: “91 MMI navigation database concerns
(Missing traffic info, Incorrect speed limits, Missing streets; POI not listed, etc.)”).
The current release schedule for map updates:
Release Schedule
Navigation Map Release Name
CW22/15
NAR 2015/2016
CW45/15
NAR 2016
CW22/16
NAR 2016/2017
CW45/16
NAR 2017
CW22/17
NAR 2017/2018
CW45/17
NAR 2018
CW22/18
NAR 2018/2019
CW45/18
NAR 2019
CW22/19
NAR 2019/2020
CW45/19
NAR 2020
CW22/20
NAR 2020/2021
CW45/20
NAR 2021
CW22/21
NAR 2021/2022
For MIB2 infotainment systems (see attachment “MIB Map Update Strategy.pdf”):
Over-the-air navigation map updates are also available in the MMI system. Audi has designed the OTA system
to track the data used separately from the data used in the customer’s existing Audi connect subscription.
For the model year 2016 A6 and A7 Product Improvement vehicles with MIB2 Navigation, the update can be
accessed in the MMI by going to Menu >> Setup MMI >> System Update >> Online Update.
For all other vehicles with MIB2 Navigation, the update can be accessed in two different areas of the MMI:
Menu >> Audi connect >> Online map update >> Start map update now >> Online update.
Menu >> Settings >> Left Option >> System maintenance >> System update >> Online update.
The customer will not be billed for the data used when performing the OTA map update, but the customer must
have an active Audi connect subscription to use the OTA map update feature in the MMI.
Page 3 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
The OTA update for MIB2 is designed only to allow a limited number of regions to be updated in the
vehicle. To perform a complete NAR (North American Region) update, the customer or dealer will always need
to download the complete data using a computer. For certain updates, the complete NAR map update may
also be available through the service SD card. This SD card can be ordered with the part number listed in
ETKA for the North American Region (NAR). No SVM activation is required because the MMI is already preactivated for 2½ years, or five consecutive updates, from the production date of the vehicle. After this period
(even if no updates were performed), an SVM activation will be required to update the Navigation database.
The customer will need to purchase the activation documentation.
For MIB2+ & MIB3 infotainment systems (see attachment “MIB Map Update Strategy.pdf”):
Over-the-air navigation map updates are available in the MMI system. Audi has designed the OTA system to
track the data used separately from the data used in the customer’s existing Audi connect subscription.
The software update can be accessed in the MMI using the following path:
Menu >> Settings >> System maintenance >> Software update.
The customer will not be billed for the data used when performing the OTA map update, but the customer must
have an active Audi connect subscription to use the OTA map update feature in the MMI.
The OTA update for MIB2+ and MIB3 systems are designed to automatically choose the regions to be updated
based on the customer’s regular areas of driving. Thus, the customer cannot manually choose the update
regions. To perform a complete NAR (North American Region) update for MIB2+ (Not yet possible for MIB3),
the dealer will need to order the NAR map update on the SD card. This SD card can be ordered with the part
number listed in ETKA for the North American Region (NAR). No SVM activation is required because the MMI
is already pre-activated for five years for MIB2+ (10 years for MIB3). This is based on the vehicle’s production
date. After this period (even if no updates were performed), an SVM activation will be required to update the
Navigation database (currently not available for purchase for MIB2+/MIB3). The customer will need to
purchase the activation documentation once it is made available by Audi of America.
(Not available until Q2 2021)
For all MIB infotainment systems, map updates via myAudi are available for download (Retired as of March
2020):
Page 4 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
The customer must register with the myAudi
website (my.audiusa.com).
The customer will need to add the vehicle VIN
that supports MIB navigation to their myAudi
profile on the website to access the “Map
update service” (Figure 1).
Figure 1. The retired map update service on the myAudi
website (my.audiusa.com).
The vehicle must have MIB navigation for the option in the myAudi website to be activated. Vehicles with
MMI3G+, for instance, will not show this option in the myAudi portal.
To download the full map update, the customer must have an SD card that indicates it has at least 16GB of
usable space when viewed within the PC file system. The full update is typically 14GB - 16GB in size. An SD
card larger than 16GB will most likely be required.
The customer can also choose a partial map update (only a limited number of US states). When doing so, the
customer can use an SD card with less available space, as a typical partial update is 3GB - 4GB in size.
Tip: A blank 16GB SD card may contain slightly less than 16GB of usable space. Thus, a larger SD card
may be needed for a full map update.
The SD card must be formatted to FAT/FAT32/exFAT. Mac-formatted SD cards will not work in the MMI MIB
main unit. SD card types are:
4GB and less: SD (FAT/FAT32).
4GB/8GB/16GB: SDHC (FAT/FAT32).
16GB/32GB/64GB and higher: SDXC (exFAT only; will work with MIB but not with MMI3G+).
Page 5 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
During the map update process, the
performance of the MMI system may be slow,
with lagging or freezing during screen
transitions or after a selection is made. These
performance limitations should only occur
during the map update, and no repairs should
be made to correct them. A file transfer icon
appears when the map update is running the
background (Figure 2).
Figure 2. The background map update is indicated by the file
transfer icon.
Production Solution
Not applicable.
Page 6 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Service
Tip: Map activations should always be performed before updating the map data. Doing so will ensure the
navigation system is always available, and the correct map data is installed. DO NOT install the map data via
the red engineering menu of the MMI until AFTER the map activation is performed via ODIS >> Flash.
1. Using the downloaded map update on the SD
card, insert it into the MMI main unit. Once the
SD card is inserted, the customer must initiate
the download (Figure 3) function in the MMI. If
the map data is an SD Card purchased from the
parts department, this update must be
performed using the RED ENGINEERING
MENU.
For A3/A6/A7:
MENU >> Setup MMI >> System Update.
For TT3/R8NF/Q7NF/B9 A4:
MENU >> Settings >> Left Option >> System
maintenance > >System update.
The update does not start automatically when
the SD card is inserted.
Figure 3. MMI option for customer map update.
2. If the data was downloaded to the SD card
correctly, the SD card would be highlighted in
white (Figure 4). If there is no SD card
highlighted, ask the customer to troubleshoot
the issue (check the formatting and verify that
all the data is in the root directory of the media).
Figure 4. SD card that contains the map update data.
Page 7 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
3. The new version of the map data will be
indicated on the MMI screen. Selecting “Start
update” begins the update (Figure 5).
The MMI will automatically perform the update
in the background, which is indicated by the file
transfer icon in the lower left-hand side of the
MMI screen (Figure 6).
Tell the customer that the vehicle can be shut
off during the update process, but the SD card
(or other update media) should never be
removed from the MMI main unit. If the vehicle
is turned off during the update process, the MMI
will continue to perform the update in the
background for approximately 30 minutes. The
update will automatically begin again on the
next ignition cycle. The complete process can
take about 60-90 minutes with an SD card. If
Figure 5. Selecting “Start update.”
the customer chooses to use a DVD or a USB
drive via AMI, then the update may take
considerably longer.
Figure 6. The background update is indicated by the file
transfer icon.
Page 8 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
4. After the update is complete, the icon on the
lower left-hand side of the MMI screen will
disappear. Additionally, a confirmation can be
seen in the MMI system update screen (Figure
7).
Figure 7. Successful update screen.
5. The update can be verified under the MMI
Version Information screen (Figure 8).
For A3/A6/A7:
MENU >> Setup MMI >> Version Information.
For TT3/R8NF/Q7NF/B9 A4:
MENU >> Settings >> Left Option >> System
maintenance >> Version Information.
The MMI system will allow the same map data
to be overwritten at any time. This means if the Figure 8. The updated map regions will be indicated by the
customer puts the same SD card with the same calendar year listing under the region. In this figure, only
map data into the main unit after a completed
“USA, Region 6” was updated.
map update, the MMI will still indicate that a
map update is available. This does not directly
indicate the map update was incomplete; the
customer must review the “Version Information”
data and verify that the latest calendar year
listing is shown under each region (Figure 8).
Page 9 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Warranty
This TSB is informational only and not applicable to any Audi Warranty.
Additional Information
The following Technical Service Bulletin(s) will be necessary to complete this procedure:
TSB 2044694, 91 MMI navigation database concerns (Missing traffic info, Incorrect speed limits, Missing
streets; POI not listed, etc.).
All parts and service references provided in this TSB (2037809) are subject to change and/or removal. Always
check with your Parts Department and/or ETKA for the latest information and parts bulletins. Please check the
Repair Manual for fasteners, bolts, nuts, and screws that require replacement during the repair.
©2020 Audi of America, Inc. All rights reserved. The information contained in this document is based on the
latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes
at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Page 10 of 10
© 2020 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
- Advanced VCI Box, Industry-leading J2534 Pass-Thru...
- High-Speed OEM-Level Diagnostics & Programming: Unlock true...
- Coverage for 17 Car Brands & Ultra Reliability: Works...
- User-Friendly RLink Platform & Expert Support: TOPDON’s...
- 6.6 ft USB-C Cable & Portable Storage Case: The RLink J...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: A9120112037809_7
Replacement Service Bulletin Number:
MFR Communication Date: 2020-09-03
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used escaner automotriz device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way, and we’ll provide a solution within 24 hours. THINKSCAN 689BT Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- [Good News] THINKSCAN 689BT is the most competitive automotive scan tool to date, offering wireless updates with no subscription fees(valued 500Buc.ks) . With all the features of THINKTOOL PD8,PRO, built on Android 10 platform with 4-core CPU, 4GB RAM
and 64GB ROM, serving up to 5X faster than older MAX/MINI/PLUS vehicle scanners escaner automotriz, no more slow and delayed feedbacks, it's time to update your garage tool. - [Big Money Saver] Premium THINKSCAN 689BT Wireless Diagnostic Scanner Escaner Automotriz, save up to 400USD per year, includes all useful features: Full bi-directional controls, ECU coding, 34+ services, OEM all system diagnostics, Worldwide vehicles coverage, CAN FD & DoIP, FCA AutoAuth（The 689BT only provides a login and purchase portal, and users are required to register for an FCA account and pay a membership fee in order to perform the relevant automotive diagnostics)
- [3000+ Active Tests]Active testing is one of the most useful features in automotive maintenance and greatly improves mechanic efficiency. THINKCAR 689BT bidirectional scanner can send action commends to vehicle sub-systems or components for active test without using vehicle controls. It can perform various tests such as: EVAP Test, Fuel Trim Reset, Injector Buzz Test, Window/ Mirror/ Door Lock Test, Pump and Value Tests, etc. Get functions from "Diagnose>Car Model>System>Active Test".
- [Hot Advanced Features] 689BT bidirectional tool scanner for car newly adds ECU Coding, Power Balance, Flash Hidden Functions, Reset Adaptive Data, Match Replaced Components, Customize OE-Settings. Such as: 1. changing the color of interior lights 2. switching on/off the auto hold, 3. customizing dash kits 4. activating the auto side mirror folding function 5. disables auto start-stop. Note: Coding functions vary by model&year.
- 【15+ Advanced Reset & Calibration Functions】The Thinkdiag scanner provides 15+ professional maintenance functions, including:✔ Oil Reset | ✔ ABS Bleeding | ✔ Injector Coding | ✔ SAS Reset✔ TPMS Reset | ✔ BMS Reset | ✔ Transmission Adaptation | ✔ AFS Reset | ✔ Sunroof Calibration | ✔ Brake Reset | ✔ Suspension Relearn | ✔ Electronic Throttle Relearn | ✔ Seat Calibration | + More reset/relearn/calibrate/adaptive functions under automotive full systems diagnostic menu. Ideal professional OBDII scanner for mechanics and DIY enthusiasts, Thinkdiag delivers professional OE-level diagnostics with adaptive relearn capabilities for precise vehicle servicing.
- 【Full-System Diagnostics OBD2 Scanner Bluetooth】 Thinkdiag OBD2 Scanner supports all Systems diagnostic function, it can read/clear DTCs, read live data, read control module information, actuation tests and maintenance functions for ECM, BCM, SRS, TCM, BMS, TPMS, SAS, A/C system etc... It works with most car models after 1996, cover more than 120+ car brands. All car make and reset software come with 1 year update without any charge, much valuable and powerful than 1000 dollars level scanners in the market.
- 【Potential Feature Activation】 Thinkdiag diagnose obd2 scanner Bluetooth allows you to match the replaced components with ECU, activate potential functions for BMW, for GM, for Benz etc. Adjust some annoying features, adapt vehicle's settings to improve performance. No matter you are private owner or professional technician, Thinkdiag is a powerful and handy scanner in your repair tool list. Potential features are not suitable for every car models, please check with us before purchase. This superior function required newest Android OS device, it performs better on Android cell phone.
- 【Bidirectional Test/Active Test】 Thinkdiag car code reader actuates solenoids and actuators for active testing, send commands to systems/components to test their real-time working status, without using manual vehicle controls which saves much diagnostic time and effort to identify malfunction causes. You can check windows, doors, mirrors, sunroof, fans, fuel pump and other parts working status by actuation test function, thinkdiag supports 10000+ active tests. When you process Automotive full system diagnostic, you can do active test on every supported module.
- 【Intelligent Diagnostic Tool with Auto-VIN】Thinkdiag Bluetooth OBD2 scanner makes your smart phone device become a professional vehicle diagnostic tool, it compatible with Android and iOS system. Auto-VIN function supports the Thinkdiag identifies the most car models automatically, if autovin failed, you can choose car info manually. Full system Vehicle health report will be automatically created after diagnosis, report can be shared. Live Data Stream combined 4-in-1 Graphing+Data Record better for monitoring vehicle performance and analyze the abnormal parameter.
- 【Powerful Bidirectional Control -- Active Test】Good News! The THINKSCAN 662 obd2 scanner has bidirectional control function,which is the most popular feature among mechanics.This function is mainly used to test whether the executing components in the electronic control system can work normally,By requesting information from the vehicle's ECU or sending commands to the ECU module to execute commands and identify maintenance status,quickly locate the cause of the fault.Such as ABS,Fuel Injectors,Adjusting Throttle,Coolant Fans,Radiator Fans,Coolant Pumps,EV.AP Test, Fuel Trim Reset,Injector Buzz Test,Pump/ Value Test,etc. Effectively shorten diagnosis time and reduce diagnosis costs.
- 【Unlock Pro-Level Diagnostics With Half Costs】 THINKSCAN 662 obd2 scanner diagnostic tool Delivers Premium Scanning Power for Half the Price! The OBD2 scanner can handle common issues with ECM,TCM,ABS,SRS. It can easily read and clear fault codes, analyze data streams, and ensure quick identification of problems. THINKSCAN 662 bidirectional scan tool has 12 practical reset functions, including Airbag Reset,ABS Bleeding,BMS,Brake Reset, D.P.F,Throttle Adaptation,Injector Coding,OIL Reset,steering angle Reset,Gearbox,TPMS,and more. The car scanner diagnostic tool very suitable for DIY enthusiasts, car repair technicians, and small and medium-sized repair shops.
- 【Multi Functional Intelligent Car Scanner Diagnostic Tool】 Automatic VIN + Real-time Data + DTC Lookup + Historical Diagnostic Records: This OBD2 scanner features auto serch technology, allowing for car recognition without the need for manual input. The real-time data of the car ECU is read and displayed in the form of text or a 4-in-1 merged waveform chart. You can save, share, print or send the entire inspection report via email for analysis. Historical diagnostic reports help you quickly identify vehicle issues and understand the condition of the vehicle. The built-in 'feedback' module provides customized repair Operation recommendations from our certified professionals.
- 【Upgraded Hardware + Ergonomically Engineered】 THINKSCAN 662 OBD2 scanner has a friendly combination of touch screen and physical buttons with an ergonomic appearance for comfortable use.Experience 2x faster scans and 50% longer lifespan vs standard models.This scanner para autos boast a 4-core 1.8GHz CPU,6.2-inch HD touch screen,2GB RAM + 32GB ROM storage capacity,a long-lasting 4150mAh battery,Android 8 ensures lightning-fast bootup and processing.The scanner is robust with rubberized protection that you can store and use in the trunk or garage.Whether you are engaged in Home car maintenance or road rescue car repair,this car scanner can help you perfectly solve car problems.
- 【Effortless Setup & Scanning - Intuitive for All Skill Levels】No More Complicated Scanners! The User Interface is as User-Friendly as THINKCAR 689BT! Truly Plug-and-Play,The downward sliding setup shortcut portal and drawer function shortcut portal make you use this scan tool as easy as using your own cell phone.The car scanner supports setup screenshot,screen recording,volume adjustment,this scan tool includes product e-manuals,instructional videos,and fault code libraries,users can check the usage guide,perfect for DIY car owners,Maintenance technician.If your father,husband,brother,boyfriend enjoys car repairs,THINKSCAN 662 is a great gift choice, and it has amazing family value.
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.