NHTSA ID Number: 10177823
Manufacturer Communication Number: WRD-20R
TSB/Document Date: 2020-08-03
Summary
Subaru
of America, Inc. (Subaru) is initiating a new safety recall for certain 2019 model year Ascent, Impreza, Legacy, and Outback vehicles in which the fuel pump may become inoperative.
ATTENTION:
GENERAL MANAGER
q
PARTS MANAGER
q
CLAIMS PERSONNEL
q
IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
SERVICE MANAGER
q
© 2020 Subaru of America, Inc. All rights reserved.
PRODUCT CAMPAIGN BULLETIN
APPLICABILITY:
SUBJECT:
2019MY Legacy and Outback 2.5 and 3.6L
2019MY Impreza
2019MY Ascent
Fuel Pump Impeller Failure
NUMBER: WRD-20R
DATE: 04/23/20
NHTSA: 20V-218
REVISED: 07/16/20
INTRODUCTION:
Subaru of America, Inc. (Subaru) is initiating a new safety recall for certain 2019 model year Ascent,
Impreza, Legacy, and Outback vehicles in which the fuel pump may become inoperative.
DESCRIPTION OF THE DEFECT AND SAFETY RISK:
The affected vehicles may be equipped with a low pressure fuel pump which includes an impeller
that was manufactured with a lower density. If the surface of the lower density impeller is exposed
to solvent drying for longer periods of time, it may develop fine cracks. Those cracks may lead to
excessive fuel absorption, resulting in impeller deformation. Over time, the impeller may become
deformed enough to interfere with the body of the fuel pump, potentially causing the low pressure
fuel pump to become inoperative.
If the low pressure fuel pump becomes inoperative, the check engine warning light or malfunction
indicator light may illuminate, and/or the engine may run rough. In the worst case, an inoperative
fuel pump may result in the engine stalling without the ability to restart the vehicle, increasing the
risk of a crash.
AFFECTED VEHICLES:
A total of 188,207 U.S. vehicles will be affected by this recall, as listed below:
Model Year
Carline
Production Date Range
Affected Vehicle Count
2019
Ascent
June 26, 2018 - January 18,2019
40,950
2019
Impreza
June 18, 2018 – February 25, 2019
40,797
2019
Legacy
June 29, 2018 – February 19, 2019
20,182
2019
Outback
June 29, 2018 – February 19, 2019
86,278
Not all vehicles in the production ranges listed above are affected by this recall. Coverage must be
confirmed by using the Vehicle Coverage Inquiry function on Subarunet.com prior to repair. The
status of this recall has been updated to “Open”.
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.
Continued...
Bulletin Number: WRD-20R; Revised: 07/16/20
Page 1 of 49
SERVICE, PARTS, AND CLAIM INSTRUCTIONS:
Sufficient remedy parts supply is now available. The remedy parts must be ordered through PRIME.
Please refer to ‘Recalls & Campaigns/PRIME Max Quantities’ on Subarunet for the orderable
quantities.
RETAILER RESPONSIBILITY:
Please be advised that it is a violation of Federal law for a dealer to deliver a new motor
vehicle covered by a recall under a sale or lease until the defect is remedied. Therefore, any
Authorized Subaru Retailer failing to perform the applicable service procedures to correct all
affected vehicles in their inventory prior to the vehicle being placed in service may be subject
to civil penalties of up to $21,000 per violation (i.e., for each vehicle), as provided in 49 CFR
§578.6 and will also be in breach of the Subaru Dealer Agreement.
Any vehicles listed in any recall/campaign that are in retailer stock must be:
•
Immediately identified
•
Tagged or otherwise marked to prevent their delivery or use prior to repair
•
Repaired in accordance with the repair procedures outlined in the Product Campaign Bulletin
Retailers are to promptly perform the applicable service procedures to correct all affected vehicles in
their inventory (new, used, demo & SSLP).
In addition, whenever a vehicle subject to this recall is taken into retailer inventory necessary steps
should be taken to ensure the recall correction has been made before selling or releasing the vehicle.
OWNER NOTIFICATION:
Subaru will notify affected vehicle owners by first class mail on June 4, 2020. A copy of the owner
letter is shown at the end of this bulletin.
Now that sufficient quantities of the Fuel Pump Kits are available, repairs using complete Fuel Pump
Assemblies must be discontinued.
Retailers with ongoing repairs using complete Fuel Pump Assemblies may complete them and submit
for payment using the claim reimbursement information located on pg. 41 of this bulletin.
For the remaining vehicles included in this campaign, the parts required to perform these repairs have
been assembled into Fuel Pump Kits, numbered for each model and labeled accordingly as shown
below to help insure installation of the proper kit into the applicable model.
Description
WRD-20 Fuel
Pump Kit
Kit Part Number
Model Application
X4202AL000
Legacy / Outback 2.5L
X4202AL010
Legacy / Outback 3.6L
X4202FL000
Impreza
X4202XC000
Ascent
Continued...
Bulletin Number: WRD-20R; Revised: 07/16/20
Page 2 of 49
The illustrations below list the component part content breakdowns for each of the four kits:
X4202FLOOO/PUMP IMPREZA
Part Number
42029FL020**
42025FL01A
42032FL01A
42056FL000
Part Name
KIT FUEL PUMP: Contains fuel pump, filter sock, fuel
pump o-rings, and c-clip.
GASKET FUEL PUMP
RING NUT
PLUG TEMPORARY
Qty
Part Number
1
42029XC000**
1
1
1
42025FL000
42032FL000
42057FL000
42056FL000
X4202ALOOO/PUMP LEGACY/OBK 2.5L
Part Number
42029AL000**
42025AL040
42056FL000
Part Name
KIT FUEL PUMP: Contains fuel pump, filter sock, fuel
pump o-rings, c-clip, and fuel pump cushions (3).
GASKET FUEL PUMP
PLUG TEMPORARY
X4202XCOOO/PUMP ASCENT
Part Name
KIT FUEL PUMP: Contains fuel pump, filter
sock, fuel pump o-rings, and c-clip.
GASKET FUEL PUMP
RING NUT
PLATE RING NUT
PLUG TEMPORARY
Qty
1
1
1
1
1
X4202ALO1O/PUMP LEGACY/OBK 3.6L
Qty
Part Number
1
42029AL010**
1
2
42025AL030
42056FL000
Part Name
KIT FUEL PUMP: Contains fuel pump, filter sock, fuel pump
o-rings, c-clip, and fuel pump cushions (3).
GASKET FUEL PUMP
PLUG TEMPORARY
Qty
1
1
2
** NOTE: The “KIT FUEL PUMP” part numbers supplied are for reference only and cannot be
ordered separately.
Continued...
Bulletin Number: WRD-20R; Revised: 07/16/20
Page 3 of 49
ADDITIONAL REQUIRED MATERIALS / SPECIAL TOOLS:
•
42099FL030 Fuel Pipe Adapter: Connects directly to the
fuel pump outlet pipe at the fuel tank. Each retailer will be
receiving two (2) of these automatically when they become
available. Remove & discard the temporary plug before
use.
•
SOA635161 Hose Fuel: This is a commonly
available service part which can be used on all
affected vehicles. This adapts the incoming fuel
supply pipe and a section of bulk rubber fuel
line. Each retailer will be receiving two (2) of
these automatically when they become available. An additional fuel draining procedure will
be added to this bulletin once these parts are available at retailers. See APPENDIX A on
starting pg. 43 for more information.
•
42099CA010 (for Legacy and Outback) and
42099FL020 (for Ascent and Impreza) Fuel
Tank Caps: To be put back into the fuel
pump opening in the fuel tank after pump
removal. These caps will help contain fuel
odors and prevent contamination from
entering the tank while the pump assembly
is removed. Each retailer will be receiving
two (2) of each part number automatically
when they become available.
•
42099FL000 Ring Nut Wrench: Used to remove and install
the fuel pump assembly locking rings on Ascent
and Impreza. This is already a required essential Subaru
Special Service Tool.
•
18471AA000 Fuel Pipe Adapter: Used to drain fuel by
connecting one end to the supply pipe connector at the fuel
rail in the engine compartment and a length of bulk fuel hose
going to a safety gasoline container on the other. This tool is
already a required essential Subaru Special Service Tool and
will be only be needed when performing repairs if fuel
draining is required.
•
42099AE000 Release Tool: Used to disengage the fuel
pipe connector in the engine bay. This is already a required
essential Subaru Special Service Tool.
Continued...
Bulletin Number: WRD-20R; Revised: 07/16/20
Page 4 of 49
NOTE: These adapters are only necessary when there is a need to lower the fuel level in the fuel
tank:
• To drain fuel directly from the fuel pump outlet, use adapter 42099FL030.
•
To drain fuel from the fuel pipe hard line in the engine compartment, use adapter
SOA635161. See APPENDIX A starting on pg. 43 for more information.
•
To drain fuel from the fuel rail connection in the engine compartment, use adapter
18471AA000.
In addition, some or all of the following 3) three items are needed to
facilitate draining the fuel tank when required.:
• A readily available 5/16” barbed hose connecting nipple
•
A 5-foot section of bulk 5/16” rubber fuel hose
•
Two (2) small fuel line hose clamps.
IMPORTANT: A length of door edge guard, flexible tubing or heavy duty electrical tape to apply
around the fuel pump access opening to avoid cuts / abrasions from sharp edges is required for all
fuel pump replacement repairs.
SERVICE PROCEDURES / TABLE OF CONTENTS:
Carline
Begins on Page
Legacy / Outback
8
Impreza & Ascent TIPS
17
Impreza
20
Ascent
29
Service Procedure Information for ALL MODELS:
NOTE: The following information is intended to SUPPLEMENT the following and Service Manual
procedures.
VERY IMPORTANT: To avoid gasoline spillage, THIS PROCEDURE MUST BE
PERFORMED WHEN THE FUEL LEVEL IN THE TANK IS AT OR BELOW 2/3 FULL. If
over 2/3 full, the tank will need to be drained to 2/3 or less before attempting to remove the complete
fuel pump assembly.
ALWAYS follow ALL the CAUTIONS and procedures for safely releasing fuel pressure and
draining fuel from the fuel tank as supplied in the applicable Service Manual.
ALWAYS remove the fuel filler cap to release any accumulated vapor pressure as a first step.
If draining fuel from the fuel tank is necessary, follow the applicable procedure this bulletin along
with “USING THE SELECT MONITOR” procedure in the applicable Service Manual.
Continued...
Bulletin Number: WRD-20R; Revised: 07/16/20
Page 5 of 49
When removing the rear seat cushion (all models
except Ascent), if the plastic retaining clips (a) (p.n.
64396KA010 for Legacy / Outback and 64333FJ000
for Impreza) in the floor come out, they become
one-time use items and MUST be replaced during
reassembly. When installing the seat cushion, always
confirm the seat belt buckles are returned to the proper
positions.
When removing the fuel pump access cover, there is a foam seal between the cover and the vehicle
body. Use CAUTION when removing the cover to not damage the foam seal. If found to be or if it
becomes damaged, the replacement seal part numbers are: 96077AJ00A for Legacy / Outback and
96077FL00A for Impreza and Ascent.
It cannot be stressed enough to have plenty of clean shop cloths and / or
absorbent pads available to use when removing the fuel line(s) from the fuel
pump. A small drip tray or pan is also recommended to use for catching any
dripping fuel when removing the fuel pump assembly from the tank.
IMPORTANT: When performing these procedures, shop cloths contaminated
with gasoline will be created. It is CRITICAL they be handled safely and
following proper disposal guidelines. Always store contaminated shop cloths in
an approved safety can as shown here.
After removing the rear seat cushion assembly and
the (main) fuel pump access cover, use a length
of small hose (sliced lengthwise), vinyl door edge
guard as shown here or electrical tape to cover the
edge of the access opening in the floor panel. This
will protect any removed fuel line(s) and Technician
hands from cuts or abrasions resulting from sharp
edges. The photo here shows the power harness
unplugged and shop cloths in place to absorb
residual fuel that may remain in the lines after
removal from the pump assembly. CAREFULLY
release the retaining clip(s) with a small flat-blade screwdriver, put a cloth over the connection and
remove the line(s). Immediately install the plug(s) provided in the replacement fuel pump kits into
the removed line(s) to avoid any spillage. This will help reduce the chances of post-repair customer
concerns of fuel odor inside the cabin.
On Legacy and Outback models, use a small container or magnetic dish to keep all the retaining ring
nuts together while the pump assembly is removed.
Continued...
Bulletin Number: WRD-20R; Revised: 07/16/20
Page 6 of 49
Have a small fuel-safe drain pan in place to catch any spilled fuel as the pump assembly is
CAREFULLY lifted out of the fuel tank. If available, use a vacuum bleeder with a collection
reservoir and hose to draw some of the stored fuel out of the fuel chamber surrounding the pump and
filter to help avoid spillage. NOTE: On Ascent, there is a jet pump fuel tube attached to the lower
portion of the fuel pump assembly as shown below, right which must also be removed before the
pump assembly can be completely removed from the vehicle. Release the retaining clip with a small
flat-blade screwdriver and remove the line but, secure the line with electrical tape or Mechanic’s wire
to keep it from falling into the tank once it is removed. If not secured, it will fall into the tank and
have to be “fished” out prior to reinstalling the pump assembly.
IMPORTANT: After the pump assembly is removed, ALWAYS install the applicable fuel tank
cap (plug) as shown below or, cover the fuel tank opening with shop cloths or a fender cover (or
an equivalent) to keep fuel odors from accumulating inside the cabin. These tools are not required
when replacing the complete fuel pump assembly due to the very short time the tank will be open to
complete the repair.
IMPREZA / ASCENT
LEGACY / OUTBACK
LEGACY / OUTBACK 2.5 & 3.6L PUMP
NOTE: When searching STIS for the applicable
Service Manual procedures for reference, select Fuel
Filter REMOVAL to get the detailed procedure for
separating the pump / filter sock assembly from the
complete fuel pump assembly. Fuel Filter removal
is NOT required to complete this procedure. The
replacement pumps come with a new filter sock
already in place as shown here.
- Restores fuel economy
- Stabilizes ethanol
- Maximizes horsepower
- Improves responsiveness
- For use in both gasoline and diesel engines
- DESIGNED TO EXCEED EXPECTATIONS: Red Line complete SI-1 fuel...
- PERFORM AND PROTECT: Fuel additive cleans injectors...
- EFFICIENT FUEL BURN: Gas treatment that enhances gasoline...
- EASY TO USE: Use one bottle per tank for most effective...
- 15 Ounce (2 Pack)
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: WRD-20R
Replacement Service Bulletin Number:
MFR Communication Date: 2020-07-16
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: FUEL SYSTEM, GASOLINE
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- Stay Updated with Lifetime Access: This obd2 scanner includes lifetime free software updates for all app service functions. With a single payment, enjoy full access to diagnostics, reset tools, and maintenance features — zero subscription fees. A budget-friendly choice for weekend mechanics, home car owners, and DIYers, supporting vehicles from 1996 onward. Come to us with your VIN to check compatibility.
- Full Bidirectional Control/Active Tests & Stable Wireless Connectivity: This car code reader features full bidirectional control, allowing you to send commands to the vehicle's ECU for active tests on components such as fuel pumps, injectors, A/C clutches, windows, sunroofs, and more. This car scanner diagnostic tool helps DIYers quickly diagnose and test vehicle parts, cutting down troubleshooting and repair time. With BT 4.0 wireless connectivity, you can enjoy cable-free diagnostics up to 33 feet. Stand in your garage and test windows, wipers, or even engine components—all without needing to move around your car.
- Portable Car Scanner with 26 Special Functions: Scheduled vehicle maintenance with the A30M car diagnostic scanner can keep your vehicle in peak condition and save you big on dealership trips. The XTOOL A30M obd2 scanner diagnostic tool features essential reset and relearn functions, such as Oil Reset, EPB Reset (Electronic Parking Brake Release), SAS, ABS Brake Bleeding, Throttle Body Relearn, Injector Coding, Crank Sensor Relearn, Headlight Adjustment, and Tire Size Reset. Note: Service functions may vary by vehicle model – check compatibility beforehand!
- Wide Compatibility CAN FD & FCA
Autoauth: This obd2 scanner diagnostic tool is compatible with over 85+ car brands from the U.S., Europe, and Asia, providing extensive coverage through a BT connection with your smartphone or iPad. Now upgraded to support the latest protocols, it includes FCA AutoAuth access for Chrysler, Jeep, Dodge, and Fiat (2018+), and supports CAN FD for GM (2020+) models, giving you greater access to newer vehicles and systems. Note: The FCA AutoAuth account is not included with the device. Users must register and pay separately through the official FCA AutoAuth website to access diagnostic functions for vehicles that require it. - Up to 8 Live Data Streams Graphing – Real-Time Graphing for Deeper Insight: This car scanner supports up to 8 live data streams simultaneously with intuitive, real-time graphing. Gain comprehensive insights into your vehicle’s performance, making it easier to spot issues, detect trends, and make informed diagnostic decisions with confidence.
- Comprehensive OBD2 Scanner with 16 Resets: The XTOOL D5S car code reader and vehicle reset tool provides an advanced diagnostic solution with 16 commonly needed reset functions, including Electronic Parking Brake Reset (EPB Reset), SAS, BMS Reset (Battery Test), Throttle Body Relearn, TPMS Reset, ABS Bleeding, Injector Coding, Gearbox Match, Suspension Adjustment, Headlight, Window Initialization, Crank Sensor Relearn and more. Equipped with CAN FD Protocol and FAC AutoAuth, the D5S obd2 scanner diagnostic tool ensures compatibility with a broad range of modern vehicles, allowing users to address common maintenance needs quickly. NOTE: Please Check the Compatibility before ordering.
- 4 Main System Car Scanner & Full OBD2 Diagnostics: The XTOOL D5S car code reader is ideal for home mechanics, DIYers, and professionals, providing access to Transmission/Engine/ABS/SRS systems to read DTCs, Live data can be displayed in text or up to 4 PID data graphs, along with full OBD2 diagnostics to check the engine light on, other obd2 issues and routine maintenance. This car diagnostic scanner ensures you can keep your vehicles in top condition, avoiding costly repairs or unexpected breakdowns. NOTE: Some vehicles display three systems after connection because the transmission and engine of some vehicles are integrated into one.
- Check Engine Code Reader & Real-Time Engine Monitoring: Whether you're a car owner, a DIYer, or run a repair shop, the XTOOL D5S obd2 scanner diagnostic tool makes engine diagnostics fast and frustration-free, reading and explaining trouble codes in seconds—no confusion. Check live data like fuel trim, 02 sensor voltage, RPM, and coolant temp to pinpoint mis~fires, rough idle, or sensor issues. After repairs, simply use the D5S check engine code reader and reset tool to turn off the check engine light and confirm the problem’s fixed—saving time, money, and unnecessary shop visits. - Note: If the check engine light comes back on, it indicates the original problem still exists.
- Portable Car Scanner for ABS and SRS: XTOOL D5S gives you peace of mind when ABS or airbag warning lights come on. It reads and clears ABS codes to help you fix brake sensor, traction control, or wheel speed issues, and supports ABS bleeding after repairs like caliper or master cylinder replacement. For airbag systems, it scans and clears SRS codes related to airbags, seatbelt tensioners, and crash sensors. Whether you're doing repairs at home or running a small shop, the D5S is a cost-effective solution for safety diagnostics. Note: If a fault code returns after clearing, it usually means the issue hasn’t been fully resolved. Please check the compatibility before ordering.
- Transmission Warning Light ON? Here’s the Transmission Diagnostic and Reset Tool You Need: The XTOOL D5S is more than just a basic car scanner—it’s an easy-to-use transmission diagnostic tool. From rough shifts to slipping gears, the D5S lets you read and clear transmission trouble codes, monitor real-time TCM data, and perform transmission resets after fluid changes or repairs. Whether you’re a hands-on car owner or a pro running a busy shop, this OBD2 scanner with transmission functions helps you catch problems early—saving you time, money, and future headaches.. Note: Clearing fault codes is equivalent to a reset on some vehicles, but not all. For help, contact XTOOL Tech Support.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations
- 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.