Service Bulletin
July 14, 2020

20-032
Version 1

AWD Indicator Comes On with DTC C1843-62 or C1844-62
AFFECTED VEHICLES
Year

Model

Trim Level

VIN Range

2019

RDX

AWD

5J8TC2…KL000001 to 5J8TC2…KL032180

SYMPTOM
The AWD indicator comes on with DTC C1843-62 (left rear differential fluid pressure deviation) and/or DTC C1844-62 (right
rear differential fluid pressure deviation).
POSSIBLE CAUSE
There is internal corrosion in the solenoids.
CORRECTIVE ACTION
Check the rear differential fluid level, and if OK, replace both rear differential solenoid valves.
PARTS INFORMATION
Part Name

Part Number

Quantity

Solenoid Assy., L. Linear

48360-5YP-013

1

Solenoid Assy., R. Linear

48350-5YP-013

1

Washer, Filler Plug (20 MM)

94109-20000

1

Part Name

Part Number

Quantity

All-Wheel Drive Fluid (DPSF)

08200-9007A

1 bottle will repair 5 vehicles.

REQUIRED MATERIALS

CLIENT INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and
training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this
bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized
Acura automobile dealer.

© 2020 American Honda Motor Co., Inc. – All Rights Reserved

Page 1 of 4

WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation
Number

Description

Flat Rate
Time

Defect
Code

Symptom
Code

Template
ID

Failed Part Number

2191BY

Replace both rear
differential solenoid
valves after checking
the rear differential
fluid.

0.5 hr

00801

03205

B20032A

48360-5YP-003

Skill Level: Repair Technician
INSPECTION PROCEDURE
1. Raise the vehicle on the lift. Refer to the service information.
2. Check the rear differential fluid, and make sure the fluid is at the same level as the filler plug hole.



If the fluid level is OK, install a new filler plug sealing washer and torque the filler plug to 35 N·m (26 lb-ft). Then, go
to REPAIR PROCEDURE.
If the fluid level is low, fill the rear differential with Acura All-Wheel Drive Fluid (DPSF) to the proper level. Refer to
the service information. Then, go to STEP 3.

3. Clear the DTCs, and test-drive the vehicle.



If the AWD indicator comes on with DTC C1843-62 (left rear differential fluid pressure deviation) and/or DTC
C1844-62 (right rear differential fluid pressure deviation), go to REPAIR PROCEDURE.
If the AWD indicator does not come on and no DTCs return, no further repairs are needed, this bulletin does not
apply.

Page 2 of 4

REPAIR PROCEDURE
Replace the left and right differential solenoid valves.

1. Remove the differential solenoid covers.

Page 3 of 4

2. Remove the differential solenoid valves.
NOTE
Before removing the solenoids, clean around each solenoid to prevent contamination from entering the differential
and/or the new replacement solenoid.

3. Install the new differential solenoid valves, and torque the bolt to 12 N·m (9 lb-ft).
NOTE
Lube the O-ring using Acura All-Wheel Drive Fluid (DPSF) before installing the differential solenoid valves to the rear
differential.
4. Install the differential solenoid covers, and torque the bolts to 12 N·m (9 lb-ft).
5. Do an All DTC check, and clear DTCs from all systems.

END

Page 4 of 4