T-SB-0049-20

May 28, 2020

Front Bumper Cover Gap at Fender
Service
Category

Vehicle Exterior

Section

Exterior Panels/Trim

Market USA

Applicability
YEAR(S)

MODEL(S)

2014 - 2020

4Runner

ADDITIONAL INFORMATION

Introduction
Some 2014 – 2020 model year 4Runner vehicles may exhibit a gap due to disengagement of the front
bumper cover clips and the fender retainer near the headlamp assembly. Follow the Repair Procedure in
this bulletin to address this condition.

Production Change Information

This bulletin applies to vehicles produced BEFORE the Production Change Effective VINs
shown below.
MODEL

PLANT

DRIVETRAIN

4Runner

Tahara

4WD

PRODUCTION CHANGE EFFECTIVE VIN

JTEBU5JR#L5790365
JTEBU5JR#L5790414

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

BD1920

Remove the Front Bumper Cover and Replace
the Retainers. Apply 3M™ Dual Lock™
Fasteners on the Front Bumper Cover and
Retainers and Reinstall the Front Bumper Cover.

1.0

52115-35152
52116-35152

62

99

APPLICABLE WARRANTY
 This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date.
 Warranty application is limited to occurrence of the specified condition described in
this bulletin.

© 2020 Toyota Motor Sales, USA

Page 1 of 9

T-SB-0049-20

May 28, 2020

Page 2 of 9

Front Bumper Cover Gap at Fender
Parts Information
PART NUMBER
PART NAME

QTY

52115-35153

Support, Front Bumper Side, RH

1

52116-35153

Support, Front Bumper Side, LH

1

Garnish Set

1

PREVIOUS

NEW

52115-35152
52116-35152

67069-35010

Repair Procedure

1. Confirm the condition exists.
Does the vehicle exhibit a gap due to disengagement of the front bumper cover clips and the
fender retainer near the headlamp assembly?


YES — Continue to step 2.



NO — This bulletin does NOT apply. Continue diagnosis using the applicable
Repair Manual.

Figure 1.

© 2020 Toyota Motor Sales, USA

T-SB-0049-20

May 28, 2020

Page 3 of 9

Front Bumper Cover Gap at Fender
Repair Procedure (continued)

2. Remove the front bumper cover.
Refer to TIS, applicable model and model year Repair Manual:


2014 / 2015 / 2016 / 2017 / 2018 / 2019 / 2020 4Runner:
Vehicle Exterior – Exterior Panels/Trim – “Exterior Panels/Trim: Front Bumper: Removal”

3. Remove the old retainers and Install the NEW retainers.
Figure 2. Retainers

2

1

1

Left-hand Side Retainer (Part No. 52116-35153)

2

Right-hand Side Retainer (Part No. 52115-35153)

NOTE
You MUST order the garnish set (part no. 67069-35010) BEFORE continuing to step 4.
Figure 3. Primer Application and Dual Lock™ Fastener Installation Areas on the Front Bumper Cover

1

1

Along the Side Wall

© 2020 Toyota Motor Sales, USA

T-SB-0049-20

May 28, 2020

Page 4 of 9

Front Bumper Cover Gap at Fender
Repair Procedure (continued)

4. Clean ALL front bumper cover and retainer surfaces where the Dual Lock™ Fasteners will
be installed, using 3M™ PAC Cleaner No. 300.
NOTE
Use one cleaner pack to clean ALL surfaces.
Figure 4. Front Bumper Cover and Retainer Cleaning Surfaces

1

1

1

Clean Using 3M™ PAC Cleaner No. 300

© 2020 Toyota Motor Sales, USA

T-SB-0049-20

May 28, 2020

Page 5 of 9

Front Bumper Cover Gap at Fender
Repair Procedure (continued)

5. Apply 3M™ PAC Primer K-500 to the surface on each side of the front bumper cover where
the Dual Lock™ Fasteners will be installed and allow it to dry for AT LEAST two minutes.
Figure 5.

1

1

Apply 3M™ PAC Primer K-500

NOTE
Ensure the primer is completely dry BEFORE continuing to step 6.

© 2020 Toyota Motor Sales, USA

T-SB-0049-20

May 28, 2020

Page 6 of 9

Front Bumper Cover Gap at Fender
Repair Procedure (continued)

6. Apply 3M™ PAC Primer K-500 to the retainer surface on each side where the Dual Lock™
Fasteners will be installed and allow it to dry for AT LEAST two minutes.
Figure 6.

1

1

Apply 3M™ PAC Primer K-500

NOTE
Ensure the primer is completely dry BEFORE continuing to step 7.

© 2020 Toyota Motor Sales, USA

T-SB-0049-20

May 28, 2020

Page 7 of 9

Front Bumper Cover Gap at Fender
Repair Procedure (continued)

7. Apply the larger Dual Lock™ Fasteners (35 mm x 20 mm) to each side of the
front bumper cover.
Figure 7.

25 mm

1

A
2

A

Front Bumper Cover Side Wall

1

Apply Along the Shape

2

Apply Along the Line

8. Apply the smaller Dual Lock™ Fasteners (25 mm x 20 mm) to both side retainers. Paste the
Dual Lock™ Fasteners inside the cut-out area.
Figure 8.

1

1

Cut-out Area on the New Retainer

© 2020 Toyota Motor Sales, USA

T-SB-0049-20

May 28, 2020

Page 8 of 9

Front Bumper Cover Gap at Fender
Repair Procedure (continued)

9. Confirm proper Dual Lock™ Fastener adhesion by pressing on ALL Dual Lock™ Fasteners.
Figure 9.

1

1
B
A

A

Retainer

B

Front Bumper Cover Side Wall

1

Press

1

Press

NOTE
Make sure the bottom of each Dual Lock™ Fastener is completely pasted on the front bumper
cover and retainer surfaces.

10. Insert the washer from the set on each side
bumper flange around the wheel arch during
the front bumper cover reinstallation.

Figure 10.

© 2020 Toyota Motor Sales, USA

T-SB-0049-20

May 28, 2020

Page 9 of 9

Front Bumper Cover Gap at Fender
Repair Procedure (continued)

11. Reinstall the front bumper cover.
Refer to TIS, applicable model and model year Repair Manual:


2014 / 2015 / 2016 / 2017 / 2018 / 2019 / 2020 4Runner:
Vehicle Exterior – Exterior Panels/Trim – “Exterior Panels/Trim: Front Bumper: Installation”

12. Press on the area where the fasteners are
installed to ensure the Dual Lock™
Fasteners are properly engaged AFTER the
front bumper cover installation has
been completed.

Figure 11.

1

1

Press

13. Visually confirm the overall front bumper cover condition has improved.

© 2020 Toyota Motor Sales, USA