NUMBER:
GROUP:
DATE:

18-047-20
18 - Vehicle Performance
May 16, 2020

This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.

This bulletin supersedes Service Bulletin 18-023-19 REV. B, dated November 1, 2019, which
should be removed from your files. All revisions are highlighted with **asterisks** and
include additional Diagnostic Trouble Code (DTC) and LOP.
SUBJECT:
Flash: Powertrain Control Module (PCM) Updates
OVERVIEW:
This bulletin involves reprogramming the PCM with the latest available software.
MODELS:
2019

(KL)

Jeep Cherokee

NOTE: This bulletin applies to vehicles within the following markets/countries: North
America, LATAM, APAC and EMEA.
NOTE: This bulletin applies to vehicles equipped with a 3.2L V6 24V VVT Engine W/ESS
(Sales Code EHK).
SYMPTOM/CONDITION:
Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further
investigation the technician may find one or more of the following DTCs:
• **P2610 - PCM Internal Engine Off Timer Performance.**
• P06EF - Engine Restart Performance.
• P0456 - EVAP System Small Leak.
NOTE: If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to
determine if a leak is present in the system.
• C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation.
• P06DA - Engine Oil Pressure Control Circuit.
• P06DD - Engine Oil Pressure Control Circuit Stuck Off.
• P06DE - Engine Oil Pressure Control Circuit Stuck On.
• B25C7 - Driver Door Ajar Switch 2 Circuit Low.
• B25C8 - Driver Door Ajar Switch 2 Circuit High.
• B25C9 - Driver Door Ajar Switch 2 Stuck Closed.
• B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation.
• C10D0 - Electronic Park Brake Module Deactivated.
• P0EA5 - DC/DC Converter 2 Performance.
• P0EA6 - DC/DC Converter 2 Over Temperature.
• P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible.
• U0128 - Lost Communication With Park Brake Control Module.
• U0151 - Lost Communication With Occupant Restraint Controller.
• U0416 - Implausible Data Received From Esp.

18-047-20
•
•
•
•
•
•
•
•
•
•
•
•
•
•

-2-

U0418 - Implausible Data Received From Brake System Control Module 1.
U0599 - Invalid Data Received From DC to DC Converter Control Module 9A9.
U0299 - LOC With DC-DC Convertor 2.
U1409 - Implausible LF WSS Received.
U140A - Implausible RF WSS Received.
U059A - Invalid Data Received From DC to DC Converter Control Module 9B9.
C0542 - Brake Pressure Sensor 2 Circuit Low.
C0543 - Brake Pressure Sensor 2 Circuit High.
P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault).
P0616 - Starter Control Circuit Low.
P0617 - Starter Control Circuit High.
P0607 - ECU Internal Performance.
P3032 - Barometric Pressure Sensor Performance Plausibility.
P0071 - Ambient Air Temperature Sensor Performance.

Some customers may also experience one or more of the following conditions:
• Engine doesn’t restart after a Engine Start/Stop (ESS) event.
• Erroneous display of “Cruise Control Unavailable Below Min Speed”.
• Erroneous display of “Speed Limited In 4LO” while in 4HI.
DIAGNOSIS:
Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in
DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or
symptom conditions, other than the ones listed above are present, record the issues on the repair
order and repair as necessary before proceeding further with this bulletin.
If a customer describes the symptom/condition listed above or if the technician finds DTCs, perform
the Repair Procedure.
REPAIR PROCEDURE:
NOTE: Install a battery charger to ensure battery voltage does not drop below 13.2 volts. Do
not allow the charging voltage to climb above 13.5 volts during the flash process.
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
1. Reprogram the PCM with the latest software. Detailed instructions for flashing control modules
using the wiTECH Diagnostic Application are available by selecting the application’s “HELP”
tab.
2. Clear any DTCs that may have been set in any module due to reprogramming. The wiTECH
application will automatically present all DTCs after the flash and allow them to be cleared.
3. Perform a hard reset on the PCM using wiTECH.
4. Turn the ignition off for a minimum of 30 seconds to complete the flash.

-3-

18-047-20

POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
Labor Operation Description
No:

Skill Category

Amount

**18-19-06-CA

1 - Engine
Repair and
Performance

0.3 Hrs.**

Module, Powertrain Control (PCM) - Reprogram
(0 - Introduction)

NOTE: The expected completion time for the flash download portion of this procedure is
approximately 6 minutes. Actual flash download times may be affected by vehicle
connection and network capabilities.
FAILURE CODE:
The dealer must use failure code CC with this Service Bulletin.
• If the customer’s concern matches the SYMPTOM/CONDITION identified in the Service
Bulletin, failure code CC is to be used.
• When utilizing this failure code, the 3C’s (customer’s concern, cause and correction) must be
provided for processing Service Bulletin flash/reprogramming conditions.
CC

Customer Concern