2020

Pre-Delivery Inspection
Technician Reference Document

Effective 4-20-2020-US
Version 1.6

Table of Contents
Technician Reference Document
Technician Reference Document Overview
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with
the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more
efficient, and in doing so, this document has been created to be used as a reference for checklist items that
may have additional information. On the PDI Checklist, you find that certain items have been notated with an
asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference
Document.
Below you will find a list of each model, with the page numbers to their left. After navigating to the desired
page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the
original checklist item, followed by any additional information specific to that model.

Table of Contents
3-4

A3/S3/RS 3

5-6

A4/S4/A4 allroad

7-8

A5/S5

9-11

A6/S6/A6 allroad

12-14

A7/S7

15-16

A8 L/A8 e/S8

17-18

e-tron

19-20

Q3

21-23

Q5/Q5 e/SQ5

24-25

Q7/SQ7

26-27

Q8/SQ8/RS Q8

28-29

R8

30-31

TT/TTS/TTRS

Effective 4-20-2020-US
Version 1.6

Model Year 2020 | Audi Pre-Delivery Reference Document | 2

A3/S3/RS 3
Technician Reference Document
Vehicle Preparation

Lighting and Windshield

•      Set adaption channel to enable CD Ripping using Guided
Functions (if equipped with NAV)

•      Test front washers (and headlight washers on S3 and RS 3).
Correct aim if necessary

Set adaptation channel (via Special functions > Service work
> 5F-Activating/deactivating storage of music). Also referred
to as CD Ripping. Perform 3 button reset of the MMI to
complete the activation. Refer to the owner’s manual for
model-specific button sequence
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan

Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Verify temporary inflatable spare tire is present (A3 Sedan
and S3 FWD only)
See separate “Audi Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)

•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding

•      Check rear view mirror operation

•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically

•      Verify proper operation of climate control

•      Install front license plate carrier (if necessary)
•      Retain any removed trim required for carrier installation
and give to the customer. If no front license plate carrier
is necessary ensure the carrier remains in the trunk for
the customer
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)

Check self-dimming function/lighting
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation (Sedan
only)
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set time source setting to “GPS” (if equipped) and set auto
daylight savings time to “on”*
Change time zone appropriate to dealer location
•      Verify and set language and measurement units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings

Effective 4-20-2020-US
Version 1.6

Model Year 2020 | Audi Pre-Delivery Reference Document | 3

A3/S3/RS 3
Technician Reference Document
Settings (continued)

Driving Performance

•      Verify Speech Dialog System is operating (if equipped)

•      Verify engine Start-Stop System functionality

Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level (if
equipped)
Via “Menu > Vehicle > Left Option > Driver Assistance >
Parking Aid”
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning
This can be changed in the Driver Assistance Settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select OffMedia / Radio / SAT

Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)

Media / Radio / SAT

Driver Assistance

•      Verify HD Radio is turned “off”

•      Verify operation of Audi parking system (if equipped)

This can be found in the Radio/Settings Menu

Verify operation of Audi parking system sensors with rear
view camera (if equipped)

Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)

Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature

Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable satellite map view for navigation (if equipped)
Enable satellite map view in the Navigation > Map Settings
and verify the satellite imagery appears in the navigation
map screen
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure
Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door
jamb, and store tire pressure values in Car/System menu
Effective 4-20-2020-US
Version 1.6

Model Year 2020 | Audi Pre-Delivery Reference Document | 4

A4/S4/A4 allroad
Technician Reference Document
Vehicle Preparation

Trunk Inspection (continued)

•      Perform any open campaigns

•      Set spare tire pressure

Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
•      Install front license plate carrier (if necessary)
•      Retain any removed trim required for carrier installation
and give to the customer. If no front license plate carrier
is necessary ensure the carrier remains in the trunk for
the customer
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Lighting and Windshield
•      Test front washers (and headlight washers if equipped).
Correct aim if necessary
Headlights must be on to test functionality of the headlight
washers

See separate “Audi Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
•      Check rear view mirror operation
Check self-dimming function/lighting
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid”
•      Set “Music volume while parking” to medium

Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit

Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)

Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
Effective 4-20-2020-US
Version 1.6

Model Year 2020 | Audi Pre-Delivery Reference Document | 5

A4/S4/A4 allroad
Technician Reference Document
Settings (continued)

Driver Assistance (continued)

•      Set dealership location in navigation (if equipped)

•      Verify all vehicle Head-up display functionality (if
equipped)

Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual > Select Off

Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-up display (as
equipped)
Post-Road Test Inspection

Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu

•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature

On-Hoist Inspection

Audi connect® (USA ONLY) (if equipped)

•      Inspect wheel bolts for proper torque

•      Turn on the Wi-Fi® hotspot (if equipped)

Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure
Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door
jamb, and store tire pressure values in Car/System menu

Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.

Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Effective 4-20-2020-US
Version 1.6

Model Year 2020 | Audi Pre-Delivery Reference Document | 6

A5/S5
Technician Reference Document
Vehicle Preparation

Trunk Inspection (continued)

•      Perform any open campaigns

•      Set spare tire pressure

Follow instructions listed in campaign documentation
•      Perform diagnostic work
Connect vehicle diagnostic tester
•      Select “Diagnosis” mode and start diagnosis
•      Perform vehicle identification
•      Untick “Working with Guided Fault Finding”
•      Switch to “Special functions” tab and select following
program:
Delivery Inspection total
•      Start program by selecting “Carry out check”
•      Continue to follow instructions on screen and complete
the process
•      Switch to the “Control units” tab, press the “Guided Fault
Finding” button and launch Guided Fault Finding as far
as the test plan
•      The static event memory entries must be evaluated and,
if necessary, processed using Guided Fault Finding
•      Exit diagnosis; diagnostic log for delivery inspection is
sent automatically
•      Install front license plate carrier (if necessary)
•      Retain any removed trim required for carrier installation
and give to the customer. If no front license plate carrier
is necessary ensure the carrier remains in the trunk for
the customer
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)

See separate “Audi Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and measurement units
This can be changed in the Setup/Settings menu
•      Verify Speech Dialog System is operating
Press the “Talk” button and verify several commands

Lighting and Windshield
•      Test windshield washers. Correct aim if necessary
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
Effective 4-20-2020-US
Version 1.6

•      Set “Entertain. Fad.” in Parking aid to an audible level
Via Menu > Vehicle > Driver Assistance > Parking Aid
•      Set “Music volume while parking” to medium
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Model Year 2020 | Audi Pre-Delivery Reference Document | 7

A5/S5
Technician Reference Document
Settings (continued)

Driver Assistance (continued)

•      Turn off Manual Speed Warning (if equipped)

•      Verify all vehicle Head-up display functionality (if
equipped)

This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual->Select Off
Media / Radio / SAT

Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)

•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
On-Hoist Inspection
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure
Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door
jamb, and store tire pressure values in Car/System menu
Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations

Convertible Functionality (if equipped)
•      Test operation of power folding top
Perform with engine running to conserve battery power
Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Audi connect® (USA ONLY) (if equipped)
•      Turn on the Wi-Fi® hotspot (if equipped)
Ensure the wireless network is turned on (Telephone > Right
Option > Wi-Fi® options > Wi-Fi® “On”)
•      Check Wi-Fi® hotspot visibility. No data available at PDI (if
equipped)
Check Wi-Fi® hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth view for navigation (if equipped)
Enable Google Earth view in the Navigation > Map Settings
and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol.

•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance