NHTSA ID Number: 10173483
Manufacturer Communication Number: P054415
TSB/Document Date: 2020-04-06
Summary
Exhaust Gas Temperature Sensor Bank 1 Sensor 1 - Circuit Short To Battery or Open
REMOTE DIAGNOSTICS REPAIR INSTRUCTIONS
DTC:
SPN 100 FMI 1 // P0524 - 00
Bulletin:
Date:
RD17-024
June 11, 2018
Engine Oil Pressure Sensor/Switch Range/Performance - Signal
plausibility failure
Description:
Applies to:
US10 – US Emissions
For Spanish click here: ESPAÑOL
General Information
These repair instructions are intended to address the following fault(s):
DTC
SPN 100
FMI 1 //
P0524 00
Description
Engine Oil Pressure
Too Low
Possible (Observable)
Symptoms
Possible Cause
x
x
x
x
x
x
Low engine oil level (EOL)
Contaminated oil, slow flowing or too thin
Reduction valve
Worn oil pump
Engine oil pressure (EOP) sensor
Oil leakage
x
x
Low Power
Reduced engine
output and engine
switch-off if the
vehicle speed falls
below 3 km/h (2 mph)
when engine
protection is chosen
in the data set
Required Parts
Part Number
Description
Quantity
22899626
Oil Pressure Sensor
1
968559
1
Repair Instructions
Oil Pressure Sensor, Replacement
Removal
1. Apply the parking brake and place the shift lever in neutral.
2. Disconnect all cables from the negative (ground) battery terminals to prevent personal injury from electrical
shock and prevent damage to electrical components.
3. Raise the vehicle hood.
Page 1 of 3
© 2016 Volvo
Group North America, LLC. Information is subject to change without notice.
REMOTE DIAGNOSTICS REPAIR INSTRUCTIONS
DTC:
SPN 100 FMI 1 // P0524 - 00
Bulletin:
Date:
RD17-024
June 11, 2018
4. Disconnect the wiring harness connector from the EOP sensor (thermal management) installed in the oil filter
housing.
5. Remove the EOP sensor and O-ring from the oil filter housing.
Installation
1. Install the replacement EOP sensor into the oil filter housing and tighten to specification (see Function Group
20 torque specifications). Be sure to use a new O-ring on the sensor.
2. Reconnect the wiring harness connector to the EOP sensor.
3. Close the vehicle hood.
4. Reconnect all previously removed cables to the negative (ground) battery terminals.
5. Clear any diagnostic trouble codes (DTCs).
6. Start and run the engine and check for leaks.
7. Check the engine oil level and add engine oil as needed.
Page 2 of 3
© 2016 Volvo Group North America, LLC. Information is subject to change without notice.
REMOTE DIAGNOSTICS REPAIR INSTRUCTIONS
DTC:
SPN 100 FMI 1 // P0524 - 00
Bulletin:
Date:
RD17-024
June 11, 2018
Additional Resources
These repairs are the most likely fix for the identified fault, if this does not fix the issue, Tech Tool will need to be used
for more detailed diagnostics. If filing a warranty claim, please include the ASIST case number.
Labor Code
3864-03-02-10
0.4 – 0.5 (Depending on model)
Causal Part
22899626
Page 3 of 3
© 2016 Volvo Group North America, LLC. Information is subject to change without notice.
INSTRUCCIONES DE REPARACIÓN DE DIAGNÓSTICO REMOTO
DTC:
Descripción:
Se aplica a:
SPN 100 FMI 1 // P0524 - 00
Boletín: RD19-026
Fecha: 16 de septiembre de 2019
Rango/Rendimiento de sensor/interruptor de presión de aceite
del motor - Falla de plausibilidad de la señal
Emisiones de US10 - US
Para inglés, haga clic aquí: ENGLISH
Información general
Estas instrucciones de reparación están destinadas a abordar las siguientes fallas:
DTC
Descripción
x
x
SPN 100
FMI 1 //
P0524 - 00
Presión de aceite de
motor demasiado baja
Posibles síntomas
(observados)
Causa posible
x
x
x
x
Bajo nivel de aceite del motor (EOL)
Aceite contaminado, fluidez lenta o
demasiado delgado
Válvula de reducción
Bomba de aceite desgastada
Sensor de la presión del aceite del
motor (EOP)
Fuga de aceite
x
x
Baja potencia
Potencia reducida del
motor y apagado del
motor, si la velocidad
del vehículo baja de
3 km/h (2 mph) cuando
se elige protección del
motor en el conjunto
de datos
Piezas necesarias
Número de pieza
Descripción
Cantidad
22899626
Sensor de presión del aceite
1
968559
Aro sello
1
Instrucciones de reparación
Sensor de presión de aceite, Reemplazo
'HVLQVWDODFLyQ
1. Aplique el freno de estacionamiento y coloque la palanca de cambios en punto muerto.
2. Desconecte todos los cables de los terminales negativos (tierra) de la batería para evitar lesiones por
descargas eléctricas y daños en los componentes eléctricos.
3. Levante el capó del vehículo.
© 2016 Volvo Group North America, LLC. Información sujeta a cambios sin previo aviso.
INSTRUCCIONES DE REPARACIÓN DE DIAGNÓSTICO REMOTO
DTC:
SPN 100 FMI 1 // P0524 - 00
Boletín: RD19-026
Fecha: 16 de septiembre de 2019
4. Desconecte el conector de arnés de cableado desde el sensor EOP (administración térmica) instalado en la
carcasa del filtro de aceite.
5. Retire el sensor EOP y el aro sello desde la carcasa del filtro de aceite.
Instalación
1. Instale el sensor EOP de reemplazo en la carcasa del filtro de aceite y ajuste según las especificaciones
(ver especificaciones de torsión del Grupo de funciones 20). Asegúrese de utilizar un nuevo aro sello en el sensor.
2. Reconecte el conector del arnés de cableado al sensor EOP.
3. Cierre el capó del vehículo.
4. Vuelva a conectar todos los cables retirados anteriormente a los terminales negativos (tierra) de la batería.
5. Elimine los códigos de diagnóstico de problemas (DTC).
6. Encienda y deje funcionar el motor y compruebe si hay fugas.
7. Revise el nivel de aceite del motor y agregue aceite de motor, si es necesario.
© 2016 Volvo Group North America, LLC. Información sujeta a cambios sin previo aviso.
INSTRUCCIONES DE REPARACIÓN DE DIAGNÓSTICO REMOTO
DTC:
SPN 100 FMI 1 // P0524 - 00
Boletín: RD19-026
Fecha: 16 de septiembre de 2019
Recursos adicionales
Es muy probable que estas reparaciones solucionen la falla identificada; si esto no soluciona el problema, se
requerirá el uso de Tech Tool para diagnósticos más detallados. Si presenta una reclamación de garantía, incluya el
número de caso ASIST.
Código de trabajo
3864-03-02-10
0.4 – 0.5 (según el modelo)
Pieza causal
22899626
© 2016 Volvo Group North America, LLC. Información sujeta a cambios sin previo aviso.
- High density negative paste, improves performance and...
- Enhanced life alloy or Silver Calcium stamped alloy...
- Calcium lead positive grid, maximizes conductivity and...
- Robust envelope separator with puncture resistant back...
- Vent cap design that resists acid leakage
- High density negative paste, improves performance and...
- Enhanced life alloy or Silver Calcium stamped alloy...
- Calcium Lead positive grid, maximizes conductivity and...
- Robust Envelope Separator with puncture-resistant back...
- Vent cap design that resists acid leakage
Last update on 2026-05-30 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: P054415
Replacement Service Bulletin Number:
MFR Communication Date: 2020-03-09
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ENGINE
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Newly Added in 2026: 7 Reset Functions] The 2026 new version of the OBD2 scanner diagnostic tool CRP123X V3.0 Elite has new special functions for F.REE: Throttle Ad.aptation, Oil/SAS/BMS/Brake Reset, D-P.F Re.generation and ABS Service. Before you visit a mechanic, launch obd2 Scanner CRP123X Elite can perform a more in-depth diagnosis of the car system and provide accurate data within minutes. What's more, the list of compatible models has been expanded. Upgrading frequency is regular, occurring monthly even weekly.
- 🔥[FCA AutoAuth + CAN FD & DoIP] As an upgraded version of the LAUNCH CRP123X/CRP129X, FOXWELL NT614, and ANCEL FX2000, The Newest LAUNCH CRP123X V3.0 auto diagnostic scanner supports the following new protocols: CAN-FD for 2020 and newer G.M and Chrysler
models, as well as DoIP for V.olvo, Land Rover/Jaguar, and B.MW F/G chassis. With integrated AutoAuth, you can diagnose 2018 and newer FCA cars equipped with S.GW. Note: CAN-FD and DoIP protocols require an additional obd2 cable. *Menus vary by make, model, and year of gasoline or diesel engine vehicle. Email us your VIN data. - 🔥[No extra software fee. Works on 90 vehicle brands.] Most OBD2 scanners work with vehicles manufactured after 2001. However, the LUNCH OBD2 scanner is compatible with OBDII-equipped vehicles built after 1996 and works with more than 90 vehicle brands. One-click lifetime updates over WIFI 2.4&5.0Ghz keep the car software current and ensure constant coverage additions, diagnose vehicles from 1996 to 2026 with a massive global database. Android 8.1 ensures lightning-fast boot-up and processing.
- [Accurate & Intuitive Multi System Diagnosis] Will you be confused about what happens when the warning light of transmission, ABS, and SRS Airbag check engine flashes? Launch obd2 scanner diagnostic tool CRP123X V3.0 to pinpoint the problem components for a faster diagnosis for your car instead of taking your car to the dealership. Generate vehicle health reports with one click and share them via email over Wi-Fi to help avoid blind maintenance. And will turn off the warning light for you after fixing the problem, make to know more about your cars and do your own repair.
- [Multiple Display of Live Data + DTC Code Definition Explanation] Launch car tools show real-time data of oil temp, pressure, transmission temp, engine speed, coolant temperature, you will know which car part is abnormal. Data can be shown in a single, multi- graph, and merge two graphs for analysis（or 4-in-1 merged waveform graph),you can save, share, print, or email the overall inspection report for easier analysis.🔥Code Search,DTC Library provide massive information. Inbuilt “Feedback” module provides customized repair suggestions from our certified professionals.
- 【2026 UPGRADED VERSION, NEW CHIPS, ADD MORE FUNCTIONS, No Extra Software Fee】Faster! The 2026 CRP123I V3.0 car diagnostic scanner has a new processor✅Android 8.1, 2+64GB of memory, 5-inch touchscreen (720P), 6100mAh rechargeable battery✅FCA SGW, New Protocol CANFD & DoIP✅Work with BST360 Battery Tester & i-TPMS Tire Pressure Detector Tool（Purchase Separately）✅2.4&5GHz dual WiFi,One-touch Lifetime Free update for 100+ Global brands(1996-2026),help you access,diagnose and fix more vehicles faster,upgrade of CRP123I V2.0.
- 【Newly Added 7 RESET FUNCTIONS】+ 【BATTERY VOLTAGE TEST】2026 New Ver. scan tool CRP123I V3.0 ADDS NEW SPECIAL FUNCTIONS-Throttle Adaptation,Oil Reset,SAS Reset,ABS Bleeding,BMS Reset,EPB Reset, DPF Regeneration,to maintain your vehicle system safely and efficiently.Graphing the battery voltage easier and more intuitive for the real-time monitors to check.It does not only reveal what error codes your car is producing,but also erase your vehicle's check engine light after the problem is fixed.
- 【Multi System Diagnostic Tool】LAUNCH CRP123I V3.0 obd2 scanner check ABS/SRS/AT/ENG systems &10 OBD2 modes, read/clear fault codes,Online Google Search, 4 IN 1 Graphing.Store and playback of dynamic data stream help to quick analysis and diagnosis. Generate vehicle health reports with one click and share them with your email via Wifi which helps avoid blind maintenance. CRP123I costs less, in the long run, saving you up to $2000 each year.
- 【Lifetime Free Update + FCA SGW +CAN FD & DoIP】This scan tool features One-click wifi update and fre e for fixing more bugs; Realtime battery voltage graphing helps to Judge the state of the battery; Auto Vin,facilitate accurate diagnosis and provide useful information.Besides,CRP123I V3.0 support AutoAuth for FCA SGW,For 2017 and later FCA Vehicles with Secure Gateway Module (SGW);New Protocol CANFD & DoIP cover more newer car and boost 4X faster data transfer（need extra adapters).
- 【Cover 10000+ Models & 100+ Car Brands】CRP123I V3.0 Elite code reader for cars and trucks is capable of diagnosing fault codes on more than 10000+ vehicles from 1996 to 2026 and 90+ car makes worldwide. Support almost all 12V OBDII cars such as SUVs, minivans, light-duty trucks, etc. It's an excellent tool for all types of mechanics from novice to pros. NOTICE: Compatibility will vary on vehicles' model and year, pls reach us via Q&A/message before purchase.
- [2026 X431 PRO3 V+ Elite] A great value for the X431 series that differs from similar diagnostic tools by adding: 1) J2534 protocol for over $800 in savings; 2) CANFD/DOIP support for enhanced communications; 3) Configuration of over $900 worth of HD(heavy truck) modules, needed purchase HD diagnostic software by HD vehicle model for use.; 4) A 10.1 inch Gorilla screen with 1280*800 resolution and 80% more touch screen sensitivity
- [J2534 Protocol Scan Tool] The J2534 Direct Access Device can be used as a factory scanning tool at no cost to you, saving you over $2,000. You can easily expand your ECU protocol capabilities for Toyota, Honda, VW, BMW, Ford, GM, Chrysler, Mercedes-Benz and more. The LAUNCH X431 PRO3 V+ ELITE Scan Tool is equipped with the newly upgraded smartlinkC V2.0. smartLinkC is a communication interface that supports the J2534 specification. It can also be used as a J2534 PassThru device to implement the J2534 protocol with a PC that has OEM diagnostic software installed.The J2534 protocol is the only way to solve problems ranging from drivability and power loss to poor fuel economy
- [Top Hardware Configuration, Upgraded Version of V+] LAUNCH Diagnostic Scanner adopts Android 10.0 OS; CPU is 4-core processor with 2.0 GHz, which greatly improves the speed of running multi-tasks. 2.4GHz/5GHz; 6300mAh/7.6V ultra-large capacity battery; 10.1 inch Gorilla screen, sunlight readable, 8MP camera; Auto VIN; 4GB+64GB storage; 20x transfer rate to save more vehicle files and customer data; New TYPE A interface to connect expansion tools such as oscilloscopes, sensors, etc.; Supports more than 25 software languages such as EN, DE, FR, SP and JP
- [60+ Reset 3000+ Active Test] Full Bi-Directional Scan Tool quickly detects problems and guides repairs based on the response of actuators such as air conditioning clutches, windows, doors, mirrors and more. With the touch of a finger, you can easily send command signals from the scanner to a variety of modular actuators, testing component integrity and functionality in minutes or even seconds to determine if a replacement or repair is needed. In addition, the machine enjoys 60+ special services such as oil reset, ABS brake bleed, EPB, SAS, BMS, suspension, injector reset and more, and undergoes rigorous field testing to ensure availability
- [Unrivaled Coverage, Over 200 Vehicle Brands] LAUNCH X431 PRO3 V+ Elite Automotive Scanner is suitable for over 200 vehicle brands, including commercial vehicles and new energy vehicles. This professional car scanner supports: 1) J2534/D-PDU protocol for HD trucks; DoIP/CANFD for Land Rover/Jaguar, BMW F/G chassis, GM, etc.; 2) FCA Autoauth, covering 2018+ Chrysler/Dodge/Fiat, etc. New/old models, all covered. Includes frequently updated vehicle software and car coverage for faster support of other new models
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.