NHTSA ID Number: 10173165
Manufacturer Communication Number: U17_P040200
TSB/Document Date: 2020-04-02
Summary
Engine Exhaust Gas Recirculation 1 Valve PositionFlow Excessive Detected
DTC:
P0402-00
GDC18-058
Bulletin:
August 10, 2018
Date:
Description:
Applies to:
Engine Exhaust Gas Recirculation 1 Valve Position
Flow Excessive Detected
US13 - US Emissions
For Spanish click here: ESPAÑOL
General Information
These repair instructions are intended to address the following fault(s):
DTC
Description
P0402-00
Engine Exhaust Gas
Recirculation
Differential Pressure
- Mechanical system
not responding
properly
Possible Cause
x
x
x
x
x
Connector
Wiring harness
EGR Valve
Charge air system leakage
EGR differential pressure sensor
Possible (Observable)
Symptoms
EGR mass flow above
calculated value
Required Parts
Part Number
Description
Quantity
22181342
EGR Differential Pressure Sensor
1
9812483
Extractor Tool
1
Repair Instructions
EGR Differential Pressure Sensor, Replacement
Removal
1. Secure the vehicle for service by parking it on a flat level surface, applying the parking brake, chocking
the rear wheel, and placing the transmission in neutral.
2. Disconnect all cables from the negative (ground) and positive battery terminals to prevent personal injury
from electrical shock and prevent damage to electrical components.
3. Raise hood. Note: Some models may be equipped with fender extenders attached to the inner splash
guard. Remove these as an assembly.
© 2016 Mack Trucks
, Inc. Information is subject to change without notice.
Page 1/4
DTC:
P0402-00
Bulletin:
Date:
GDC18-058
August 10, 2018
4. Disconnect the wiring harness lead from the connector terminal on the EGR pressure differential sensor.
Loosen and remove the mounting bolts and remove the EGR pressure differential sensor from the venturi
tube. Note: Install new sealing rings when replacing the sensor.
Old Style EGR
Differential Pressure
New Style EGR
Differential Pressure
5. Clean the sealing surface where the EGR differential pressure sensor mounts into the EGR venturi tube.
Ensure that the ports of the venturi tube are fully open and free of debris.
Note: If the ports to the EGR differential pressure sensor are clogged check the entire EGR system for
clogging and debris. Clean the system as needed.
Installation
Note: If replacing an old style EGR differential pressure sensor with a new style sensor, perform Installation Steps
1 through 3. If replacing a new style EGR differential pressure sensor with a new style sensor, skip to Installation
Step 4.
Note: When installing the kit for the updated EGR differential pressure sensor for the D13 engine, the engine
harness connector pins will need to be relocated. The previous pin locations were:
x Pin 1 — Green/White
x Pin 2 — Brown
x Pin 4 — White/Brown
© 2016 Mack Trucks, Inc. Information is subject to change without notice.
Page 2/4
DTC:
P0402-00
Bulletin:
Date:
GDC18-058
August 10, 2018
Note: The new engine harness connector pin locations when replacing old style EGR differential pressure sensor
with the new style sensor in kit are:
x Pin 1 — Green/White
x Pin 2 — Brown/White
x Pin 3 — Brown
1. Clip applicable cable ties and remove P-clamps securing the EGR differential pressure sensor harness
leg.
2. Use extractor tool (part number 9812483) in kit 88890037 to relocate the engine harness connector pins.
Special tools: 9812483
3. Connect the EGR differential pressure sensor jumper harness to the engine harness.
4. Install the EGR differential pressure sensor.
5. Install the EGR differential pressure sensor fasteners. Tighten fasteners to specification. Refer to
Function Group 20, Specifications.
© 2016 Mack Trucks, Inc. Information is subject to change without notice.
Page 3/4
DTC:
P0402-00
Bulletin:
Date:
GDC18-058
August 10, 2018
6. Connect the EGR differential pressure sensor harness.
7. Install all previously removed cables to the ground (negative) battery terminals.
8. Due to the electronic control module (ECM) self-learning capability, it is necessary to reset learned ECM
parameters after servicing some engine related components. This allows the ECM to learn the new
components behavior. After servicing is complete, perform the “Learned Data Reset” using Tech Tool.
This is located in the Function Group 1 menu.
9. If applicable, install the inner splash guard assembly.
10. Close the hood.
Additional Resources
These repairs are the most likely fix for the identified fault, if this does not fix the issue, Tech Tool will need to be
used for more detailed diagnostics. If filing a warranty claim, please include the ASIST case number.
Labor Code
2939-03-02-01
0.4 – 0.6 (Depending on model)
Causal Part
22181342
© 2016 Mack Trucks, Inc. Information is subject to change without notice.
Page 4/4
DTC:
P0402-00
Boletín:
Fecha:
Descripción:
Se aplica a:
GDC18-032
20 de febrero de 2020
Exceso de flujo detectado en posición de válvula 1
de recirculación de gas de escape del motor
Emisiones de US13 - US
Para inglés, haga clic aquí: ENGLISH
Información general
Estas instrucciones de reparación están destinadas a abordar las siguientes fallas:
DTC
Descripción
P0402-00
Presión de diferencial
de recirculación de gas
de escape del motor Sistema mecánico
no responde
adecuadamente
Posibles síntomas
(observados)
Causa posible
x
x
x
x
x
Conector
Arnés de cableado
Válvula EGR
Fuga en el sistema de aire de carga
Sensor de la presión diferencial
de EGR
Flujo de masa de
EGR sobre el valor
calculado
Piezas necesarias
Número de pieza
Descripción
Cantidad
22181342
Sensor de presión diferencial de EGR
1
9812483
Herramienta de extractor
1
Instrucciones de reparación
Sensor de presión diferencial de EGR, Reemplazo
Desinstalación
1. Asegure el vehículo al estacionarlo en una superficie plana, aplicar el freno de estacionamiento, bloquear
la rueda trasera y poner la transmisión en neutro.
2. Desconecte todos los cables de los terminales positivos y negativos (tierra) de la batería para evitar
lesiones por descargas eléctricas y daños en los componentes eléctricos.
3. Levante el toldo. Nota: Algunos modelos pueden estar equipados con extensores de guardabarro a
la protección interna contra salpicaduras. Retírelas como un conjunto.
© 2016 Mack Trucks, Inc. La información está sujeta a cambios sin aviso previo.
Página 1/4
DTC:
P0402-00
Boletín:
Fecha:
GDC18-032
20 de febrero de 2020
4. Desconecte el terminal del arnés de cableado desde el terminal del conector en el sensor de presión
diferencial EGR. Afloje y retire los tornillos de montaje y retire el sensor de presión diferencial EGR
desde el tubo venturi. Nota: Instale los nuevos anillos de sellado cuando reemplace el sensor.
Sensor de presión
diferencial de EGR de
Sensor de presión
diferencial de EGR de
5. Limpie la superficie de sellado donde el sensor de presión diferencial de EGR se monta en el tubo venturi
EGR. Asegure que los puertos del tubo venturi estén totalmente abiertos y sin residuos.
Nota: Si los puertos al sensor de presión diferencial de EGR están obstruidos, revise el sistema EGR
completo en busca de obstrucciones y residuos. Limpie el sistema, según sea necesario.
Instalación
Nota: Si reemplaza un sensor de presión diferencial de EGR de estilo antiguo con un sensor de estilo nuevo,
realice los Pasos de instalación 1 a 3. Si reemplaza un sensor de presión diferencial de EGR de estilo nuevo
con un sensor de estilo nuevo, sale al Paso de instalación 4.
Nota: Cuando instale el kit para el sensor de presión diferencial de EGR actualizado en el motor D13, las clavijas
del conector del arnés del motor deben ser reubicadas. Las ubicaciones anteriores de las clavijas eran:
x Clavija 1 — Verde/Blanco
x Clavija 2 — Café
x Clavija 4 — Blanco/Café
© 2016 Mack Trucks, Inc. La información está sujeta a cambios sin aviso previo.
Página 2/4
DTC:
P0402-00
Boletín:
Fecha:
GDC18-032
20 de febrero de 2020
Nota: Las nuevas ubicaciones de las clavijas del conector del arnés del motor cuando reemplazan el sensor de
presión diferencial de EGR de estilo antiguo con el sensor de nuevo estilo en el kit son:
x Clavija 1 — Verde/Blanco
x Clavija 2 — Café/Blanco
x Clavija 3 — Café
1. Corte las amarras aplicables y retire las abrazaderas en P que aseguran la pata del arnés del sensor de
presión diferencial de EGR.
2. Utilice la herramienta de extractor (número de pieza 9812483) en kit 88890037 para reubicar las clavijas
del conector del arnés del motor. Herramientas especiales: 9812483
3. Conecte el arnés de puente del sensor de presión diferencial de EGR al arnés del motor.
4. Instale el sensor de presión diferencial de EGR.
5. Instale los sujetadores del sensor de presión diferencial de EGR. Apriete los sujetadores de acuerdo a
las especificaciones. Consulte Grupo de funciones 20, Especificaciones.
© 2016 Mack Trucks, Inc. La información está sujeta a cambios sin aviso previo.
Página 3/4
DTC:
P0402-00
Boletín:
Fecha:
GDC18-032
20 de febrero de 2020
6. Conecte el arnés del sensor de presión diferencial de EGR.
7. Instale todos los cables retirados anteriormente a los terminales negativos (tierra) de la batería.
8. Debido a la capacidad de autoaprendizaje del módulo de control electrónico (ECM), es necesario
restablecer los parámetros aprendidos de ECM después de reparar algunos componentes relacionados
con el motor. Esto permite que la ECM aprenda la nueva conducta de los componentes. Después de
terminar la reparación, realice el “Restablecimiento de datos aprendidos” usando Tech Tool. Esta se
encuentra en el menú del Grupo 1 de funciones.
9. Si es aplicable, instale el conjunto de protección interna contra salpicaduras.
10. Cierre el capó.
Recursos adicionales
Es muy probable que estas reparaciones solucionen la falla identificada; si esto no soluciona el problema, se
requerirá el uso de Tech Tool para diagnósticos más detallados. Si presenta una reclamación de garantía,
incluya el número de caso ASIST.
Código de trabajo
2939-03-02-01
0.5 – 0.6 (según la configuración)
Pieza causal
22181342
© 2016 Mack Trucks, Inc. La información está sujeta a cambios sin aviso previo.
Página 4/4
- Formulated for engines with 75,000 miles or more, Valvoline...
- Delivers 20% better wear protection and 15% better sludge...
- Extra detergents safeguard against friction, corrosion and...
- Advanced friction-fighting additives help maximize...
- Provides performance benefits for high mileage, new and...
- Advanced protection against the four main causes of engine...
- Delivers 40% stronger wear protection than industry...
- Provides 15% better deposit defense vs. industry standards...
- Up to 2.5X better heat protection vs. industry standards to...
- Engineered for excellent low-temperature flow, reducing...
This product presentation was made with AAWP plugin.
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: U17_P040200
Replacement Service Bulletin Number:
MFR Communication Date: 2020-03-10
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ENGINE AND ENGINE COOLING
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- 🎉[OTOFIX D1 Lite, Perfect Cost-effective Diagnostic Tool]: OTOFIX D1 Lite, a newest bidirectional scan tool from OTOFIX company, is a great choice for DIYers and repair shops. 👉This obd2 scanner diagnostic tool packs all practical functions: OE level all systems diagnoses, Bi-Directional Control, 38+ reset services fixing 99% of common problems, support DoIP & CANDF protocols and FCA
AutoAuth, high-end hardware configuration. Worldwide vehicles and 🔥2 Years Free Updating🔥 covered. - 🎉[Bi-Directional Scan Tool, Active Test]: OTOFIX D1 Lite bluetooth obd2 scanner can also command ECUs and monitor the operation of the actuators to track down the problems of certain parts, like windows, sunroof, wipers, fuel pumps, etc., saving repair time & trouble. This makes OTOFIX D1 Lite the most cost-effective bidirectional scan tool.
- 🎉[2026 Newest, 38+ Hot Reset Functions]: Equipped with 38+ reset functions in one, the OTOFIX D1 lite automotive scanner diagnostic tool allows you to troubleshoot 99% of common vehicle problems. You can use this car diagnostic scanner holding enough functions to easily repair common vehicle models in your repair shops. Including Oil Reset, Injector Coding, Throttle, DPF Reset, SCR Reset, Gear Learning, Clutch Learning, Suspension, etc. Note* Reset functions vary by model.
- 🎉[OE Level Full Systems Diagnostics]: Unlike the 2-system and 4-system diagnostic tools, the OTOFIX auto scan tool can complete comprehensive system diagnostics within 5 minutes. It accesses and scans all available onboard systems like for Engine /AT /ABS /EPB /BMS /TPMS /SRS /SAS /Audio System /BCM /Air Conditioning / etc., to read & clear codes, view live data, and check ECU information. Note: Active test is not involved.
- 🎉[Powerful Hardware Configuration]: Designed with a fashion appearance & a 7” touchscreen and a weight of 463g, this OTOFIX D1 Lite OBD2 diagnostic scanner scan tool is convenient for everywhere and easy to use & store. Android9.0 OS and 2+64GB memory enhance multi-task smoothness and diagnostic operation, no more wasting too much time. 5800mAh battery allows hours-lasting use. WiFi & VCI1 also bring faster communication for your diagnostics.
- 🏆【2026 TOP OBD2 Scanner Diagnostic Tool】OTOFIX D1 Lite wireless obd2 scanner has upgraded hardware configuration and car coverage. The newly upgraded D1 Lite with 🔥OS Android 9.0🔥1.5Ghz 4 core high efficiency processor🔥2GB RAM+64GB ROM large storage🔥5800mAh large battery, more stable and longer lasting diagnostics🔥 38+ Reset🔥action tests🔥full system diagnostic🔥Supports MV105 endoscope🔥21+ Language Supports🔥100000+ vehicle coverage to meet all your daily maintenance needs.
- 👍【Bi-Directional Control / Active Test】D1 Lite obd2 scanner has bidirectional control(worth $300+), which is the most beloved feature among mechanic. If your headlights or car windows are broken, going to a repair shop will cost a lot of money. You can use D1 Lite to send execution commands to the ECU module and identify the repair status. Such as ABS, car windows, doors, valves, wipers, headlights, etc., effectively shorten diagnostic time and reduce diagnostic costs.
- 🔥【All Systems Diagnostics, In-depth Checking】This advanced OBD2 Scanner D1 Lite can perform OE-level diagnosis of all systems including engine, transmission, airbag, ABS, ESP, TPMS, gateway, steering, radio, and air conditioning for more than 100 brands. This diagnostic scanner supports essential functions, such as reading ECU version info, reading and clearing fault codes, and reading data streams.With just a simple click, it provides you with accurate and in-depth diagnostics.
- 🏆【38+ Reset Hot Functions】For repair workshops, holding an OTOFIX D1 Lite Auto scanner is a strong advantage over others. Its 38+ maintenance functions provide various solutions for all module repairs, including Oil Reset, TPMS Reset, Injector Coding, Suspension, Throttle Matching, etc., which will usher your repair business to a new pinnacle. Continuously updating will never make the functionality & compatibility out-of-date.
- 🏆【150+ Models, 10000+ Car Coverage & 16 Languages】D1 Lite is a comprehensive car diagnostic scan tool, help you to troubleshoot car issues fast for 95% US, European, Asian auto makes. ✅ With frequent updates and optimizations allow D1 Lite to cover more vehicles to meet your needs. ✅ Multilingual menu allows auto mechanics around the world to use it without language barriers. 🚩Note: Kindly send us the S/N of the device to authorize new language updates before changing the menu language.
- 【2026 OTOFIX D1 Lite Gives the Best Value for Money】OTOFIX D1 Lite bidirectional scan tool is more FASTER and SMARTER with 2026 Enhanced Hardwares & New Functions! 👍Alternative Bluetooth +USB connect 👍2G+64GB 👍4x ARM Cortex-A35 (1.5GHz) Processor (5X Faster CPU) 👍Android 9.0 OS 👍5G GHz WiFi 👍CANFD&DOIP 👍 FCA AutoAuth 👍38+ Services 👍3K+ Bi-Directional Control 👍Full Systems Diagnose 👍2 Years Update 👍150+ Vehicle Coverage.
- 👍【Active Tests】 OTOFIX D1 Lite is a bi-directional scan tool that can send commands to, and also receive information from vehicle control modules. This way, you can quickly locate and repair faulty auto parts. For Example: send direct commands to ask the vehicle to turn on/off the radiator fan, lights, sound horn, fuel pump, modulate throttle, open/close windows, operate mirrors and more. *Note that only available tests will be displayed in the menu.
- 👍【38+ Service Functions】 OTOFIX D1 Lite scan tool offers 38+ of the hottest service functions that are commonly used for car repairs. That include Oil reset/SAS/EPB/BMS/Throttle/ABS bleeding, and 2065-new SUS/ADBLUE/NOX/Headlamp resets (and more) to help restore your car status after repairs are done. Compared to other diagnostic scanners for cars, the OTOFIX D1 Lite scanner is much more fully-featured. *Note that specific functions available depend on the make/model/year of your car.
- 👍【All System Diagnostics + Cloud Report Management】 This 2026 car scanner OTOFIX D1 Lite provides troubleshooting and data for all ECUs: read/clear DTCs, view graphic live data/VIN, and locate system faults for safe driving. With Cloud Report Management, you can save detailed reports to cloud servers and easily shared them with others via QR codes/emails/text messages. Others can access these reports from any device (smartphones/tablets/PCs …) anytime, and you can better manage repair work.
- 👍【99% Car Coverage】 This one-station car scanner diagnostic for all cars works on 150+ major car brands across the world. 1) It supports CAN-FD/DoIP protocols: compatible with GMCAVALIER/TRAX/Encore/Envision/GL8(LSY)/CT4/CT5 after 2019; Volvo after 2018; Land Rover/Jaguar after 2017; and BM.W F/G all chassis. 2) For models equipped with security modules (such as Renault & 2018+ FCA SGW), its built-in AutoAuth allows you to easily break diagnostic barriers after registration.
This product presentation was made with AAWP plugin.
Last update on 2026-06-06 / Affiliate links / Images from Amazon Product Advertising API