CAMPAIGN
BULLETIN

QUALITY ACTION

Front Wheel Sensor Harness Inspection
Reference: PC721
Date: February 14, 2020
Attention: Dealer Principal, Sales, Service & Parts Managers
Affected
Models/Years:
2019 Titan XD

Affected
Population:

Dealer
Inventory:

SERVICE COMM
Activation date:

Stop Sale
In Effect

NA

262

February 14, 2020

NO

***** Quality Action Summary *****
Nissan is conducting a quality action to inspect the right and left front wheel sensors and if
necessary replace on specific MY2019 Titan XD vehicles identified in SERVICE COMM and
National Service History – Open Campaigns. These vehicles are either currently in dealer
inventory or assigned and in transit to the dealer.
Due to a supplier quality issue, that has since been corrected; the incorrect sensor may
have been installed on the front wheel hub.
***** What Dealers Should Do *****
PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS:
1. Verify if vehicles currently in dealer inventory are affected by using Service Comm
or National Service History – Open Campaign I.D. PC721.
 New vehicles in dealer inventory can also be identified using DBS (Sales->
Vehicle Inventory, and filter by Open Campaign).
 Refer to NPSB 15-460 for additional information
 Please continue to check newly arriving inventory for campaign
applicability.
2. Use the attached procedure to inspect and, if necessary, remedy any vehicles
affected by this quality action:
 If the wheel sensor part numbers are 47910-EZ10A (GOOD). No further
repair is required.
 If ONE or BOTH of the wheel sensor part numbers are 47910-1PA0A (NG)
replace only the affected wheel sensor per the Electronic Service Manual
(ESM).
3. Once vehicles have been inspected and, if necessary, remedied dealers may submit
the applicable warranty claim for the action performed and the vehicle can be
released for sale.
***** Dealer Responsibility *****
It is the dealer’s responsibility to check Service Comm or DBS National Service History –
Open Campaign using the appropriate campaign I.D for the campaign status on each
affected vehicle currently in new vehicle inventory.

PC721 | Original Document

PC721 – 2019 TITAN XD
FRONT WHEEL SENSOR HARNESS
INSPECTION
SERVICE PROCEDURE:
1. Raise the vehicle on a suitable lift.

2. Remove both front wheel and tire
assemblies (Figure 1).


Remove (5) lug nuts from each
wheel



Remove both front wheel and tire
assemblies.

Figure 1

Wheel Sensor
Harness

Inspect for Part
Number HERE

3. Locate right front and left front wheel
sensor harnesses (passenger side [RF]
shown in Figure 2, driver side is
similar).

Inspect for Part
Number HERE

Figure 2

1/3

4. Inspect right and left front wheel sensor harness part numbers (Refer to Figures 2,
3, and 4).


Check both locations on the harness as shown in Figure 2 for the part number



If the harness is dirty, clean with a water-dampened rag (do not use cleaning
chemicals).

Hint: Turning the front knuckle assemblies will provide more clearance for the
inspection.

PN: 47910-EZ10A (GOOD)

PN: 47910-1PA0A (REPLACE)

Figure 3

Figure 4

a. If the wheel sensor part numbers are 47910-EZ10A (GOOD). No further repair
is required. Proceed to Step 5. Submit claim using Op Code PC7210.
b. If ONE or BOTH of the wheel sensor part numbers is 47910-1PA0A (REPLACE)
only the affected wheel sensor per the ESM: BRAKES > BRAKE CONTROL
SYSTEM > VDC/TCS/ABS > REMOVAL AND INSTALLTION > WHEEL
SENSOR > FRONT WHEEL SENSOR > REMOVAL AND INSTALLATION. Use
the part number listed in the Parts Information section. Torque the wheel sensor
retaining bolt to 8.25Nm (73 in-lb). Submit claim per Claims Information
section. Continue to Step 5.

5. Reinstall both front wheel and tire assemblies.


Torque wheel nuts to 177Nm (131 ft-lb)

2/3

PARTS INFORMATION:
Description

Part #

Quantity

SEN ASY ANTI SKID F

47910-EZ10A

Up to (2)

CLAIMS INFORMATION
Submit claim using the following claims coding:
Work Order Line Type: “CM” Campaign
Campaign: PC721
Claim Type:

CM

PNC:

PC721

Symptom:

ZZ

Diagnosis:

99

Description:

Op
Codes

Flat Rate
Time

Parts
Required
on claim

Expense
Code
Required

Inspect both front wheel sensors
(Good Condition)

PC7210

0.3 Hr

NO

NO

Inspect both front wheel sensors
and replace ONE front wheel
sensor.

PC7211

0.5 Hr

YES

NO

Inspect both front wheel sensors
and replace BOTH front wheel
sensors.

PC7212

0.7 Hr

YES

NO

3/3