Quick tip
Version 1.0

February 11th, 2020

Title: Extended range add on.
(Only applies to 2019 Tiguan LWB, Jetta, GLI built after CW36/18,
Atlas built after CW42/2018, 2020 Arteon)

Extended range kit part number: 000065760

Page 1 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

ver1.2

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Step 1:
•
•
•

Step 2:
Bend the door seal molding outward
in the instrument panel cover area.
Pry out the instrument panel side
cover -1- with the -3409- near the
catches.
Pull the cover toward the rear and
remove it.

•

Unclip the A-pillar gap cover -1- from the Apillar upper trim panel and A-pillar lower
trim panel -arrows-.
Loosen the A-pillar gap cover -1- from the
door seal molding and remove it upward.

Step 4:

Step 3:
•
•

•

Remove the A-pillar upper trim panel
Note: Inspect and replace the fasteners if
necessary, part numbers 5NA867276B
(x2) and 5G0867276A (x1).

•

Remove fuse panel cover.

Page 2 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Original design harness

New design harness

Step 5b:

Step 5a:
•
•
•

•

Insert red wire into the fuse holder.
Insert black/red wire into fuse holder.
Insert the 2-amp fuse into the fuse holder.

Step 6b:

Step 6a:
•

No harness preparation is required.

•

Mount the fuse holder to the bracket
on the side of the relay panel.

Insert fuse holder into location SC20,
SC7 or SC8 can be used if there is a
fuse larger than 10 amp already in
location SC20.

Page 3 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Step 7a:
•

Insert the power wire in any open
location shown above.

Original and new design harness

Step 8:
•

Step 9:

Use a cable tie and secure the module
at the base of A-pillar.

•

Route ground wire behind lower Apillar trim and connect to the chassis
ground location under the carpet
near the base of A-pillar.

Page 4 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Step 10:
•
•

On white BCM connector, insert line
wire from kit into location 54.
Note: If there is already a wire in this
location use the provided splice
connector.

Step 11:
•

•
•

Route the antenna cable (supplied in
the kit) -2- vertically on the left hand
side of the mirror mount up to the
headliner.
Tuck the cable behind the headliner
and down the “A” pillar and connect it
to the module.
Use the small wire ties -arrows- to
secure the cable to the factory
harness located within the “A” pillar.

Page 5 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Step 12:
•

Reinstall all trim panels and the BCM
connector that was previously removed.

Step 13:
•
•
•
•
•

Connect battery charger/maintainer.
Connect scan tool.
Scan the vehicle using GFF.
Select Special Functions / Adapting software.
Select Adapting Software and Option 2. Enter SVM code 425D to update BCM.

Step 14:
•

Select “OBD.”

Page 6 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Step 15:
•

Select “0009 – Central Electrics” basic settings, then select “green arrow.”

Step 16:
•

Select “adapting RF transmitter via barcode” then select the “arrow.”
Page 7 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Step 17:
•

Select the “next arrow.”

Page 8 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Step 18:
•

Enter the RF ID (HEX) and Private key (HEX) either manually with the keyboard or scan the
QR code with a scanner.

Step 19:
•

Select the “next arrow.”

Page 9 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Step 20:
•

Select “Start.”

Page 10 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Step 21:
•

After selecting “Start,” the result field should change to “[VO] Correct-Results” for a couple
seconds. The process is completed.

Step 22:
•

To test the operation, close all doors and lock the vehicle, Press the “Info” button once, then
press the “Start” button twice on the new transmitter.

Step 23:
•

Place the sticker with the RF ID (HEX) and Private key (HEX) on the extended range owner’s
manual document. Place the document in the glove box with the owner’s manual.

Page 11 of 11

“Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory,
or improper installation of the accessory can result in damage or failure.“
© 2020 Volkswagen Group of America, Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.