Service Bulletin

20-009

February 14, 2020

Version 2

High-Pitched Sound While on HFL Call
Supersedes 20-009, dated February 7, 2020, to revise the information highlighted in yellow
AFFECTED VEHICLES
Year

Model

Trim

VIN Range

2017-20

RLX

ALL

ALL

2017-20

RLX Sport Hybrid

ALL

ALL

REVISION SUMMARY
Under AFFECTED VEHICLES, the RLX Sport Hybrid was added.
SYMPTOM
There is a high-pitched sound from the speakers while on a Bluetooth® HandsFreeLink® (HFL) call.
PROBABLE CAUSE
The TCU/HFL software needs to be updated.
CORRECTIVE ACTION
Update the TCU/HFL software.
WARRANTY CLAIM INFORMATION
The normal warranty applies.
NOTE
There are multiple steps in this bulletin that takes time to download or update the software. During this time, the repair
does not require you to stay with the vehicle.
Operation
Number

Description

Flat Rate
Time

0105B1

Update and verify the
0.3 hr
TCU/HFL software, then
do the factory data
reset.

Defect
Code

Symptom
Code

Template
ID

Failed Part Number

03214

03217

B20009A

39770-TY2-A02

Skill Level: Repair Technician
CLIENT INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and
training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume
this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an
authorized Acura automobile dealer.
©

2020 American Honda Motor Co., Inc. — All Rights Reserved

Page 1 of 9

REPAIR PROCEDURE
Reflashing the TCU Software
1. Connect a fully charged jumper battery to the vehicle, and leave it connected during the entire update procedure to
maintain steady voltage.
2. Open the Acura Firmware Downloader from the shop's computer.
NOTES
•

Refer to job aid Acura Firmware Downloader for more information.

•

Make sure the USB flash drive is empty and is formatted to FAT32.

3. Enter this service bulletin number, the VIN of the vehicle you are working on, and select Search.

4. When the software is found, select the Download icon. Once the download is complete, go back to the vehicle.
NOTE
The software download may take up to 10 to 15 minutes depending on the size of the file and internet speed. You
do not need to stay with the vehicle during this download.

5. Turn the ignition to ON.
6. Before updating the software, write down the client's audio unit presets.
NOTE
Any devices that were paired to the vehicle will have to be paired again after the update.

Page 2 of 9

7. Insert the USB flash drive into the USB port.

8. Press and hold the NAV, BACK, and MENU buttons at the same time to get to the Select Diagnosis Items screen.
Then, select Detail Information & Setting.

9. On the Detail Information & Setting screen, select Unit Check.

10. On the Select Check Units screen, select TCU.

Page 3 of 9

11. On the TCU Status screen, select Reflash.

12. On the TCU Reflash screen, select Software Update and wait for the system to enter the reflash mode.

NOTE
If the system fails to enter the reflash mode, turn the ignition to OFF for 5 to 10 minutes and remove the USB flash
drive. Then, go back to step 7.

Page 4 of 9

13. Once the system is in the reflash mode, select 01.05.003, then Start Reflash.

The reflash process will take about 20-25 minutes to complete.
NOTE
You do not need to stay with the vehicle during this reflash process.

14. Once the reflash is complete, select OK and remove the USB flash drive.

Page 5 of 9

15. Select Return five times until you are back to the navigation screen.

Verifying the TCU Software
1. On the navigation screen, press and hold the NAV, BACK, and MENU buttons at the same time to get to the Select
Diagnosis Items screen. Then, select Detail Information & Setting.

2. On the Detail Information & Setting screen, select Unit Check.

Page 6 of 9

3. On the Select Check Units screen, select TCU.

4. On the TCU Status screen, make sure the SW Version is 01.05.003.

5. Select Return four times until you are back to the navigation screen.
Doing the Factory Data Reset
1. On the navigation screen, press the SETTINGS button and select System Settings.

2. On the System settings screen, scroll down and select Factory Data Reset.

Page 7 of 9

3. Select Yes twice for the two pop-ups.

4. After the factory data reset is complete, disconnect the jumper battery and park the vehicle in an open area.
5. Turn the ignition to OFF for at least 10 minutes, then turn it back to ON.
NOTES
•

Make sure the ignition is turned completely to OFF by exiting the vehicle and locking the doors.

•

You do not need to stay with the vehicle for the ignition cycle.

6. Turn the ignition to OFF again for another 5 minutes, then turn it back to ON.
7. Make sure the LED next to the LINK button is lit green.

8. Press the SETTINGS button.
9. Select Info Settings, then AcuraLink Subscription Status.

Page 8 of 9

10. Make sure Status lists OK.

.
11. Press the LINK button, and make sure it contacts AcuraLink.

12. Check the map, and make sure the AcuraLink icon is there and has reception.
13. Restore the client's audio unit presets, and make sure the client knows that any previous paired devices will need to
be paired again.
END

Page 9 of 9