NHTSA ID Number: 10171205
Manufacturer Communication Number: IS-19901A
TSB/Document Date: 2020-02-08
Summary
Revision : Mention added stating to disable Prime & parts added in the kit.
FIGURE 120
EL
Writer:
IS-19901A
Page 56 / 92
96. When stretched, the end of the ground cable and
the fan drive power cable connector should be at
approximately 1½″ to 2¼″ (38 mm to 57 mm)
from the lower flat surface.
97. Once properly adjusted, tighten the nylon ties
previously installed.
FIGURE 121
98. Apply Loctite Color Guard Rubber Coating on
the ground stud connection.
FIGURE 122: GROUND STUD WITH RUBBER COATING
EL
Writer:
IS-19901A
Page 57 / 92
99. INSTALLATION OF THE
CONTROL CABLE #069511
a) Connect the harness #069511 to the
alternator.
b) Secure the harness with nylon ties as
shown on the pictures.
FIGURE 123: C: NYLON TIES #504016 (2x)
EL
Writer:
IS-19901A
Page 58 / 92
100. Partially route the “alternator control cable”
#069511 along the “alternator power cable” as
shown on the images. Secure the “alternator
control cable” on the “alternator power cable”
using nylon ties.
A: nylon tie #504016 (9x)
B: « handcuff » type nylon tie #N37749
required
as
NOTE: The “alternator control cable” #069511
will be connected to the “fan to RJB interface”
harness #23488790. For this reason, do not route
the “alternator control cable” further than what
is shown on the images.
FIGURE 124
FIGURE 125
FIGURE 126
EL
Writer:
IS-19901A
Page 59 / 92
FIGURE 127
FIGURE 128
101. Route the “fan drive power cable” and the
“alternator power cable” up to the electrical
compartment.
DO NOT PASS THE CABLES through the upper
cable boot AT THIS MOMENT. Refer to the
pictures at right as a guide for the installation.
Secure both cables with the four (4) tie mounts
previously installed. Secure the cables on the tie
mounts as previously done with nylon ties.
A: nylon tie #509491 (8x)
DO NOT TIGHTEN THE NYLON TIES AT THIS
MOMENT
FIGURE 129
EL
Writer:
IS-19901A
Page 60 / 92
102. Route the “fan to RJB interface harness”
#23488790 up to the electrical compartment,
passing through the upper cable boot. But first,
place connector A34-J1 next to the red
connector of the fan drive power cable (see
image at right).
A: fan to RJB interface harness #23488790
FIGURE 130
103. Secure harness #23488790 along the fan
drive power cable, placing a nylon tie #504016
every 6 inches (150 mm).
DO NOT TIGHTEN THE NYLON TIES AT THIS
MOMENT
FIGURE 131
104. Secure connector C-ALT3 as shown on the
image with one (1) nylon tie #504016 and then
connect to the alternator control cable #069511
previously installed.
FIGURE 132
EL
Writer:
IS-19901A
Page 61 / 92
105. Apply Color Guard rubber coating at the
alternator ground
connections.
(
)
and
positive
(+)
FIGURE 133: GROUND CONNECTION ON THE
ALTERNATOR
FIGURE 134: POSITIVE (+) CONNECTION ON THE
ALTERNATOR
EL
Writer:
IS-19901A
Page 62 / 92
106. Pre-install the new CAC inlet pipe #050328.
Use one new #030096 CAC flexible hose.
Secure the hose using two (2) spring-loaded
clamps #21490630.
•
•
#030096 hose (1x)
#21490630 spring loaded clamp (2X), final
torque: 5 lbf-ft
NOTE: On vehicles prior serial G-5932 (2016),
remove the 90° elbow diffuser pipe and replace
with straight turbo diffuser pipe #053662. Use the
following parts:
A: straight turbo diffuser pipe #053662 (1x)
B: gasket #21096684 (1x)
C: V-band clamp #20592787 (1x)
FIGURE 135: CONNECTION AT THE TURBO OUTLET
ELBOW
107. Preinstall all the flexible hoses at the cooling
pack connections. Use the following parts:
A: flexible hose #531469 (1x)
B: flexible hose #531471 (1x)
C: silicone hose #053617 (2x)
D: clamp #21490616 (8x)
E: caillau clamp #992089 (8x)
For proper clamp torque, refer to HOSE CLAMP
TORQUE on page 14
FIGURE 136
EL
Writer:
IS-19901A
Page 63 / 92
108. Prepare the cooling pack upper attachment
with the three (3) rectangular plates (see image)
recovered from the former installation and the
following parts:
A: anti-vibration mount #21185073
B: upper radiator support #050351
C: 2x screw #5001738 , 2x nut #502837
D: 2x screw #5001738 , 2x washer #500942
E: 2x screw #5001745 , 2x washer #500942
FIGURE 137:
FIGURE 138
109. Install the upper attachment on the cooling
pack.
FIGURE 139
110. Reinstall the cooling pack in its compartment.
FIGURE 140
EL
Writer:
IS-19901A
Page 64 / 92
111. Secure the cooling pack base with the
following parts:
A: 4x screw #502804
B: 8x washer #5001751
C: 4x nut #502859
FIGURE 141
112. Bolt the anti-vibration mount onto the vehicle
chassis
FIGURE 142
EL
Writer:
IS-19901A
Page 65 / 92
113. Complete the connection
with the cooling pack.
For proper clamp torque,
refer to
HOSE CLAMP
TORQUE on page 14
FIGURE 143
114. Connect the radiator vent hose on top of the
radiator.
115. Reinstall the cooling pack protector tube with
the following hardware:
A: Screw #502804 (3x)
B: split lock washer #5001737 (3x)
C: flat washer #5001751 (2)
FIGURE 144
EL
Writer:
IS-19901A
Page 66 / 92
116. Remove all the old spring nuts on the cooling
pack and replace with new spring nuts.
•
spring nut #5001965 (18x)
FIGURE 145
117. Install the sealing element #050355. Secure
with the following hardware:
4x bolt #5001697
4x lock washer #502570
Use foam tape #506040 to fill the gap between the
sealing element and the charge air cooler if
necessary.
FIGURE 146
FIGURE 147
EL
Writer:
IS-19901A
Page 67 / 92
118. Install the sealing element #050362. Screw it
on the existing threaded holes on the bottom
of the radiator. Secure with the following
hardware:
4x bolt #5001697
4x lock washer #502570
Use foam tape #506040 to fill the gap between
the sealing element and the charge air cooler
if necessary.
FIGURE 148
119. Install the sealing element #050360. Screw
them onto the upper and lower sealing
elements installed at the previous steps.
Secure with the following hardware:
9x bolt #5001697
9x lock washer #502570
A: #050360
FIGURE 149
120. Install the sealing element #050380. Secure
with the following hardware:
5x bolt #5001697
5x lock washer #502570
B: #050380
FIGURE 150
EL
Writer:
IS-19901A
Page 68 / 92
121. Install the sealing element #050359. Secure
with the following hardware:
6x bolt #5001697
6x lock washer #502570
C: #050359
FIGURE 151
122. Cut two pieces of 39 3/8 inches (1000 mm)
long of rubber extrusion #506025.
123. Using good industrial glue (Loctite 404 or
similar product), glue the two pieces of rubber
extrusion centered on the reinforcement
angles of fan support panel #050343.
FIGURE 152
FIGURE 153
EL
Writer:
IS-19901A
Page 69 / 92
124. Install panel #050343. Secure with the
following hardware:
22 x bolt #5001697
22 x lock washer #502570
FIGURE 154
125. Install the circuit breaker box #564612.
Install with the following hardware:
4x bolt #500119
4x lock washer #5001868
FIGURE 155
126. Install the upper sealing element #050366.
Secure with the following hardware:
5x bolt #5001697
5x lock washer #502570
FIGURE 156
EL
Writer:
IS-19901A
Page 70 / 92
127. Install the pull-rod box #050369.
Secure with the following hardware:
4x bolt #5001697
4x lock washer #502570
FIGURE 157
128. Install the lower sealing element #050365.
Secure with the following hardware:
4x bolt #5001697
4x lock washer #502570
FIGURE 158
129. Install the R.H. side sealing element #050367.
Secure with the following hardware:
bolts #5001697 (5x)
lock washers #502570 (5x)
FIGURE 159
EL
Writer:
IS-19901A
Page 71 / 92
130. Install the fans and fan hand guards on the
panel. Snap the fan blue connector in the
holes punched on the panel for that matter.
Install with the following hardware:
32x bolts #502686
32x lock washers #5001833
Prescribed torque:40 lbf-in
FIGURE 160
131. Get the fan drive harnesses kit #068820. Take
note that each harness is specifically
identified with a number corresponding to
an appropriate fan location.
FIGURE 161
132. Route and secure the fan harnesses as shown
on the images.
Secure with the following parts:
A= nylon tie mount #504013 + rivet
#504379 + nylon tie #504016
(11x)
B= nylon tie #504016 (4x)
Do not tighten the nylon ties at this moment
FIGURE 162
EL
Writer:
IS-19901A
Page 72 / 92
FIGURE 163
133. Connect each fan to the corresponding
connection port on the circuit breaker box.
FIGURE 164
EL
Writer:
IS-19901A
Page 73 / 92
134. Using the blue hose previously saved, make a
protective sheath. Cut to an appropriate size
and secure around the cables using nylon ties.
FIGURE 165
EL
Writer:
IS-19901A
Page 74 / 92
135. Complete the connection to the fan circuit
breaker box (three connectors: gray, black
and red).
A: fan drive ground cable (black connector)
B: fan drive power cable (red connector)
C: “fan to RJB interface” harness (gray
connector)
Secure the cables appropriately using nylon ties
and/or « handcuff » type nylon tie #N37749 as
required
FIGURE 166
On the engine hot side, remove the radiator inlet
pipe
FIGURE 167
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: IS-19901A
Replacement Service Bulletin Number:
MFR Communication Date: 2020-01-24
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ENGINE AND ENGINE COOLING
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [2026 Top-Tier Hardware and Software Upgrade]: Topdon ArtiDiag900 Lite scanner has enhanced hardware and latest features, including Android 11.0, 5x faster CPU, 10000mAh battery for 12 hours of continuous operation, stable wireless diagnosis with Bluetooth 5.0, 8-inch touchscreen. Added bi-directional control, wireless diagnosis, battery testing (optional), and DTC repair guide
- [TOPDON Bidirectional Scan Tool]: This bidirectional obd2 scanner sends commands to the vehicle's ECU for active testing, enabling users to accurately and quickly locate faulty components such as injectors, coolant pumps, windows, wipers, headlights, mirrors, etc. The bidirectional control scanner is the ideal choice for workshops/automotive repair shops as it significantly reduces mechanic's diagnostic time.
- [Wireless Bluetooth Diagnostic Experience]: The AD900 Lite scan tool comes with a Bluetooth 5.0 VCI, supporting a wireless diagnostic range of up to 33 feet (10 meters), allowing you to diagnose without being confined to cables or tight spaces. Stable and fast wireless diagnosis provides a comfortable repair environment. It also offers VCI cables to increase connectivity options.
- [DTC Repair Guide Function]: Easily diagnose issues with your vehicle and receive guidance on repairs with the topdon scan tool's fault code definitions for all systems,maximize your diagnostic capabilities. This function is compatible with Chrysler
/Dodge/Jeep/Fiat 2010-2014 and expanding with continual updates,the AritDiag 900 Lite car diagnostic scanner is the must-have tool for any technician or DIY enthusiast. - [OE-Level Full System Diagnostics]:AritDiag900 Lite full system diagnostic scanner can scan ALL available modules(Engine, Transmission, Airbag, ABS, ESP, TPMS, Gateway, Steering, Radio, Air conditioning, ect.) to✔read ECU info, ✔read/clear codes, ✔view live data stream, ✔retrieves freeze-frame, ✔perform active tests, and more. With just a simple click, it provides you with accurate and in-depth diagnostics.
/
- Bi-Directional Control, Quickly Locate Problems: Turn your phone into a professional diagnostic tool. You can send commands from your phone to the ECU to test injectors, cooling fans, headlights, A/C clutch, windows, wipers, and more. See which one doesn't respond. Helps you quickly locate the problem and save time. No need to tear things apart, avoid blind disassembly.
- Flexible Subscription, Choose Advanced Features as Needed: TopScan Lite provides free-for-life access to core diagnostics, including full system scan, code reading, performance tests, and repair information. After purchase, advanced features (bi-directional control, service operations, live data, code clearing, and AI functions) are free-for-the-first-year. After the first year, if you want to use advanced features, you need to subscribe on a monthly, quarterly, or yearly basis. As new models and reset functions are updated, the tool will also be continuously upgraded.
- Full System Diagnostics, No Fault Hides: Unlike basic diagnostic tools that only cover 4 systems, TopScan can scan all systems. Read and clear trouble codes, view live data streams, and generate a complete vehicle health report – all issues are clear at a glance. Covers 10,000+ vehicle models and is compatible with 99.99% of vehicles.
- AI Assistant - TopFix: Think of TopFix as your personal AI mechanic. It leverages a repair database and OEM data to deliver clear, step-by-step repair solutions. Features include AI Q&A, one-click translation, and a full repair log, making your diagnostic process simpler and more efficient.
- 8+ Hot Resets, Keep Your Car in Top Shape: One-tap resets for oil, throttle, EPB, steering angle, DPF, ABS, BMS, and airbag. It enables car owners to easily perform essential maintenance, ensuring the vehicle stays in optimal condition and extends its service life.
- Dual WiFi & 10.1" Touchscreen: Provides a stable, high-speed wireless link 3x faster than bluetooth, and a responsive, professional interface. Topdon ONE obd2 scanner diagnostic tool ensures smooth, non-lagging diagnostic scan, boosting mechanic efficiency
- J2534 Pass-Thru Support: The included ONE VCI supports the J2534 standard, allowing it to function as a pass-thru device when paired with OEM diagnostic software.Through TOPDON’s RLink platform, technicians can perform dealer-level coding, expanding in-house capabilities without investing in multiple factory automotive scan tools
- OE Topology Mapping: Visualize the vehicle’s ECU network exactly as it’s built.Zoom, pan, and highlight specific modules to pinpoint component issues with precision.Topology mapping displays real-time communication between modules
- 50 Plus Service Functions: Covers high-demand services like ADAS calibration, DPF regen, TPMS reset, ABS bleed, and throttle adaptation.Expands your service menu, allows you to charge premium rates, and turns away zero jobs due to lack of tooling. Vehicle-specific functionality may vary
- Advaned ECU Coding: 10 of the most serviced brands in North America, including full ECU coding and flash hidden support for BMW, VW, Au-di, Benz, Porsche, Toyota, Ni ssan and more. Enables module replacement, feature customization, and personal settings with automatic backup or restore.Lets your shop safely offer high-margin customization services, attracting more customers and boosting profit
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.