NHTSA ID Number: 10171073
Manufacturer Communication Number: 15-211-17R
TSB/Document Date: 2020-02-05
Summary
The following information addresses reprogramming file availability and a software update installation procedure to provide optimization to the Harman Gen 3 Audio and Navigation head units.
ATTENTION:
CLAIMS PERSONNEL q
IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
SERVICE MANAGER
© 2017 Subaru
of America, Inc. All rights reserved.
GENERAL MANAGER q
PARTS MANAGER
q
q
SERVICE BULLETIN
APPLICABILITY: 2017-18MY Impreza
NUMBER: 15-211-17R
2018MY Crosstrek DATE: 06/13/17
2018MY Legacy and Outback
REVISED: 01/03/20
2018MY BRZ*
SUBJECT:
Reprogramming File Availability for Additional
Optimization of Harman Gen 3 Audio and Navigation
Head Units
INTRODUCTION:
The following information addresses reprogramming file availability and a software update
installation procedure to provide optimization to the Harman Gen 3 Audio and Navigation head units
utilized in the models as listed above. The procedure will involve either downloading the software
update files from Subarunet (or using those sent directly from Nuspire) and transferring them onto
a flash drive for head unit installation. These files do NOT include Map Update data. It is VERY
IMPORTANT to read and understand this information completely to understand all changes from
prior releases before proceeding. A time line chart along with a complete list of all the conditions
addressed by this and previous Harman 3.0 software updates is provided in “Appendix A” located at
the end of this bulletin.
IMPORTANT NOTES:
•
If a vehicle presents with a current blank or black screen condition, request an exchange unit.
•
Be sure to locate and re-format any existing USB drives used for updating Harman audio units in
order to fully clear them before adding these new files to them.
If a Map update is pending, please follow the instructions posted on Subarunet: Service
Operations & Technical > Forms/Downloads > Navigation System Map Updates and select the
applicable link.
•
CAUTION: NEVER attempt to install this software on any
2019 MY vehicles as they are equipped with Gen 3.1 Audio/
Navigation systems. This update is ONLY for models equipped
with Gen 3.0 Audio/ Navigation systems. Should an attempt be
made to install any of these files into a Gen 3.1 head unit, the
authentication error screen to the right will be displayed.
* NOTE: On BRZ models, this update applicable to HIGH / Navigation - equipped head units only.
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
SUBARU OF AMERICA, INC. IS
ISO 14001 COMPLIANT
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.
Continued...
Bulletin Number: 15-211-17R; Revised 01/03/20
Page 1 of 20
•
If the navigation maps have been recently updated, the newest software may have already been
installed at the same time. This may eliminate the need to attempt any further update of the
software. ALWAYS check the head unit’s software version prior to attempting any new software
installation.
PRODUCTION CHANGE INFORMATION:
These latest updates (June 2019) apply to the models listed above equipped with Harman Gen 3.0
Audio and Navigation head units only. They include all previous enhancements implemented in all
prior software updates INCLUDING the previously released WTN-74R updates. Therefore, if
WTN-74R is still open, these latest updates will continue to satisfy the campaign. See the
WARRANTY / CLAIM INFORMATION section at the end of this bulletin for further instructions.
The latest software version (including all available updates) was incorporated into production per the
starting VIN table below:
Model
Starting VIN
Legacy
Outback
Impreza 4-Door
Post Production
Impreza 5-Door
Crosstrek
BRZ
Multimedia System Type
Descriptive Features
6.5 Inch Display Audio System (Base)
No CD slot / Eject Button
8.0 Inch Display Audio System (Mid)
Phone Button
8.0 Inch Audio / Navigation System (High)
Map Button but no Phone Button
2018MY Legacy and Outback Harman Audio / Navigation system Faceplate images
BASE
MID
NO CD Player
PHONE Button
HIGH
MAP Button
Continued...
Bulletin Number: 15-211-17R; Revised 01/03/20
Page 2 of 20
Materials Required:
16GB (MINIMUM) USB 2.0 or 3.0 flash drives which are readily available at most office supply
retailers will be needed to perform these updates.
Recommended Flash Drives:
•
Kingston®: Data Traveler G3, G4, SE9 or the Hyper-X Series
•
SanDisk®: Cruzer Series, Ultra Flair
•
Transcend®: JetFlash 300, 600 or 790
•
Verbatim®: Store ‘n’ Go
NOTES:
• The USB flash drives can be USB 2.0 or 3.0.
•
The USB flash drive MUST be reformatted to NTFS before loading any files to it. NTFS is
not the standard format on most USB flash drives.
•
The update files are not overly large but, during the reprogramming procedure, the head unit
backs up some files to the USB drive. For this reason, sufficient USB drive memory size is
required, especially for the High / Navigation units.
•
The flash drives should be dedicated to storing these reprogramming files only. Do NOT
use any flash drives which contains or requires the use of file management, encryption, file
backup or other software to function properly.
•
Re-format (see Step 2) any prior USBs you may have used for WTN -74R as that version of
software must no longer be installed. This update includes all WTN -74R updates.
Continued...
Bulletin Number: 15-211-17R; Revised 01/03/20
Page 3 of 20
SERVICE PROCEDURE / INFORMATION:
Affected Vehicles / Audio Units:
Vehicle Model
2017-18MY Impreza &
2018MY Crosstrek
Audio Unit Type (High, Mid, Base)
Audio Unit
Part Number
NAVIGATION (HIGH)
86271FL60A
8-Inch Display Audio (MID)
6.5-Inch Display Audio (BASE)
NAVIGATION (HIGH)
2018MY Legacy /
Outback
2018MY BRZ
8-Inch Display Audio (MID)
86201FL62A
86201FL63A
86201FL60A
86201FL61A
86471AL65A
86471AL66A
86431AL65A
86431AL66A
6.5-Inch Display Audio (BASE)
86431AL61A
NAVIGATION (HIGH ONLY)
86271CA670
STEP 1- Verify the currently installed Software Version ID using the following steps:
•
After starting the engine, from the HOME screen, touch “Settings”.
•
From the Settings > General screen, scroll down to and then touch “System Information”.
Continued...
Bulletin Number: 15-211-17R; Revised 01/03/20
Page 4 of 20
•
Confirm the current Software Version ID. If the Current Version is Rel_A1.19.12.20 OR
Rel_A1.19.45.20, STOP as this latest update has already been installed.
STEP 2- Prepare the USB:
CAUTION: Do not use any USB flash drive which utilizes file organizing software or an
operating system.
•
Make sure the USB flash drive contains
no other files.
•
Right click on the corresponding
“Removable Disk”.
•
Select “Format”.
•
From the File System drop-down menu,
select “NTFS”
•
Check the “Quick Format” box (if not
already done).
•
Click on “Start” to format the USB flash
drive.
STEP 3The files are available for download on Subarunet (see “A” below).
The applicable reprogramming files have also been sent directly to retailers by Nuspire in the same
way a Select Monitor Update would be pushed out. (see “B” below).
Follow “A” when using files downloaded from Subarunet.
Follow “B” when using the files sent directly to the SDS notebook from Nuspire.
Continued...
Bulletin Number: 15-211-17R; Revised 01/03/20
Page 5 of 20
“A” When using update files downloaded from Subarunet:
Click Here to Access the Downloads for Audio/Navigation Information on Subarunet
IMPORTANT: Files downloaded from Subarunet will be .zip files and must be unzipped before
they can be used.
Using the normal audio / navigation system file update download procedure: Go to Subarunet, select
Service Operations and Technical>>Forms/Downloads>>Downloads for Audio/Navi then click on
the applicable Hyperlink to download the file(s) to your SDS Notebook or PC:
“BASE-17-18 Impreza-18 Crosstrek-18-Legacy-Outback-18-HARMAN AUDIO UPDATE-JUNE 2019”
“MID-17-18 Impreza-18 Crosstrek-18-Legacy-Outback-18-HARMAN AUDIO UPDATE-JUNE 2019”
“HIGH-17-18 Impreza-18 Crosstrek-18-Legacy-Outback-18-BRZ-HARMAN AUDIO UPDATE-JUNE 2019”
•
Go to Downloads.
•
CAUTION: After download is complete, NEVER change the file or folder names.
•
Once the files have been downloaded from Subarunet, click on the Downloads folder and then
sort by Date Modified to bring the most recent files to the top of the list.
•
Open / display the contents of File folder, for example (BASE-17-18 Impreza-18 Crosstrek18-Legacy-Outback-18-HARMAN AUDIO UPDATE-JUNE 2019).
•
Click on “Extract All Files”.
•
From the dialog box, browse to My Documents then click on “Extract”.
•
Double-click on the required file (for this example, select the file entitled “BASE-17-18
Impreza-18 Crosstrek-18-Legacy-Outback-18-HARMAN AUDIO UPDATE-JUNE 2019”).
•
Copy ONLY the “update” folder then paste (or click / drag) it to the “clean” USB flash drive
as listed (Removable Disk) in the directory.
•
To avoid confusion, label the flash drive with the file contents (e.g. BASE 3.0, MID 3.0 or
HIGH 3.0).
•
Go to Step 4.
Continued...
Bulletin Number: 15-211-17R; Revised 01/03/20
Page 6 of 20
“B” When using update files sent directly from Nuspire:
•
Go to My Documents on the GUI screen to display the list of available update files shown
below.
•
CAUTION: After download is complete, NEVER change the file or folder names.
•
Sort by Date Modified to bring the most recent files to the top of the list. The folder is named:
_Harman Audio-Navi Update Files.
•
Double-click on the required file (for this example, select the file entitled “BASE-17-18
Impreza-18 Crosstrek-18-Legacy-Outback-18-HARMAN AUDIO UPDATE-JUNE 2019”)
and the update file will display as shown.
•
Select the update folder and either copy / paste or click / drag it to the USB flash drive.
NOTE: Do not copy the entire “BASE-17-18 …” File folder. Copy ONLY the File folder named
“update” to the flash drive
•
Once the folder named “update” is loaded onto the USB flash drive, right click on the drive
and select “Eject”.
•
Remove the USB flash drive after the prompt appears that says “Safe to Remove Hardware”.
•
Mark the USB to indicate the head unit it will update (BASE in this example).
•
Repeat the above steps to create the MID and HIGH USB flash drives as needed using a
separate USB drive for each update folder.
Continued...
Bulletin Number: 15-211-17R; Revised 01/03/20
Page 7 of 20
STEP 4- IMPORTANT: Confirm the update folder on the USB flash drive is for the head unit being
reprogrammed ONLY. NEVER install multiple update folders onto the same flash drive at the same
time.
• After confirmation, move to the car and either start the engine or connect either the Subaru
Midtronics DCA-8000 Dynamic Diagnostic Charging System or the Subaru Midtronics
GR8-1100 Diagnostic Battery Charger to the vehicle and utilize the Power Supply Mode.
BASE-17-18 Impreza-18 Crosstrek-18-Legacy-Outback-18-HARMAN AUDIO UPDATE-JUNE 2019
Copy ONLY the folder named “update” to the USB.
•
Never change the folder name from “update”.
•
Confirm there is only a folder named “update” on the flash drive.
CAUTION: Confirm one final time the head unit you are about to update matches the USB flash
drive you have selected. Attempting to install the incorrect update file will disable the head unit.
STEP 5- Update Installation:
IMPORTANT: Always record the customer’s radio station presets and navigation favorites (where
applicable) before proceeding further as they will most likely need to be reset once the update and
re-boot procedures are completed. In addition, some customizable system settings may need to be
reset as they may return to the default setting during the update.
•
With the engine idling (or DCA-8000 / GR8-1100 connected), plug the flash drive into the
USB Port.
IMPORTANT NOTE: If the head unit does not recognize the USB flash drive during the
reprogramming process, this may be due to an incompatible Controller IC in the USB flash drive
or it is otherwise incompatible with the head unit. If this occurs, delete all files from the flash drive
and re-format it to “FAT32”, instead of “NTFS” and reload the appropriate “update” folder to the
USB flash drive. If the USB flash drive is still not recognized, please discontinue the use of that
drive and instead use a USB flash drive from a different manufacturer.
Continued...
Bulletin Number: 15-211-17R; Revised 01/03/20
Page 8 of 20
•
After the unit “authenticates” the USB flash drive, press “Next” and after the second screen is
displayed, press “Next” again.
NOTE: If an attempt is made to install the wrong “grade” file into the wrong grade head unit
(EXAMPLE: “Base” update file into a “Mid” or “High” head unit), the USB Authentication error
screen below will be displayed:
•
The current and available software version information will be displayed. The Available
Version I.D should be Rel_A1.19.12.20.
NOTE: The displayed Available Version as shown below does not show the _U0 after the
Rel. This is normal.
•
After confirming the Available Version, press “Install Now” to start the reprogramming
process. The screen will go blank (black) for a brief period after installation begins.
•
Each of the updates (Base, Mid and High) should take less than 10 minutes to install.
Continued...
Bulletin Number: 15-211-17R; Revised 01/03/20
Page 9 of 20
IMPORTANT NOTES:
•
Do not leave the vehicle once the update begins as ignoring pop-up requests may lead to
battery discharge.
•
Do not touch any of the buttons on the head unit while the updating process is taking place.
•
If during the updating an error screen is displayed asking “Do you want to Retry”, press
“Retry” to restart the update.
•
Once the updating process is complete, the head unit will perform a “soft” reboot.
(NOTE: several “hard” reboots are required to fully install the update. This procedure is
covered in Step 6 below.)
•
button to
CRITICAL STEP: After the reboot process completes, press the HOME
return to the HOME screen. (NOTE: If the “install message” is displayed asking if you
want to start the update process again, press “Cancel”, press the HOME button again and
return to the HOME screen.)
STEP 6- Turn the ignition OFF, open and close the driver’s door then remove the flash drive from
the USB port. If an error screen is displayed asking “Do you want to Retry”, press “Cancel”.
IMPORTANT: Wait AT LEAST 3 MINUTES before proceeding to Step 7.
STEP 7- Verify the newly-installed Software Version ID using the following steps:
•
Turn the ignition back ON. Confirm the “SUBARU STARLINK” screen is displayed. If
“SUBARU STARLINK” screen is NOT displayed on the first screen, system did not fully
enter “sleep mode” and reboot properly. Perform Step 6 again and wait AT LEAST 3
MINUTES before proceeding.
•
- Advanced VCI Box, Industry-leading J2534 Pass-Thru...
- High-Speed OEM-Level Diagnostics & Programming: Unlock true...
- Coverage for 17 Car Brands & Ultra Reliability: Works...
- User-Friendly RLink Platform & Expert Support: TOPDON’s...
- 6.6 ft USB-C Cable & Portable Storage Case: The RLink J...
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 15-211-17R
Replacement Service Bulletin Number:
MFR Communication Date: 2020-01-03
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- Stay Updated with Lifetime Access: This obd2 scanner includes lifetime free software updates for all app service functions. With a single payment, enjoy full access to diagnostics, reset tools, and maintenance features — zero subscription fees. A budget-friendly choice for weekend mechanics, home car owners, and DIYers, supporting vehicles from 1996 onward. Come to us with your VIN to check compatibility.
- Full Bidirectional Control/Active Tests & Stable Wireless Connectivity: This car code reader features full bidirectional control, allowing you to send commands to the vehicle's ECU for active tests on components such as fuel pumps, injectors, A/C clutches, windows, sunroofs, and more. This car scanner diagnostic tool helps DIYers quickly diagnose and test vehicle parts, cutting down troubleshooting and repair time. With BT 4.0 wireless connectivity, you can enjoy cable-free diagnostics up to 33 feet. Stand in your garage and test windows, wipers, or even engine components—all without needing to move around your car.
- Portable Car Scanner with 26 Special Functions: Scheduled vehicle maintenance with the A30M car diagnostic scanner can keep your vehicle in peak condition and save you big on dealership trips. The XTOOL A30M obd2 scanner diagnostic tool features essential reset and relearn functions, such as Oil Reset, EPB Reset (Electronic Parking Brake Release), SAS, ABS Brake Bleeding, Throttle Body Relearn, Injector Coding, Crank Sensor Relearn, Headlight Adjustment, and Tire Size Reset. Note: Service functions may vary by vehicle model – check compatibility beforehand!
- Wide Compatibility CAN FD & FCA
Autoauth: This obd2 scanner diagnostic tool is compatible with over 85+ car brands from the U.S., Europe, and Asia, providing extensive coverage through a BT connection with your smartphone or iPad. Now upgraded to support the latest protocols, it includes FCA AutoAuth access for Chrysler, Jeep, Dodge, and Fiat (2018+), and supports CAN FD for GM (2020+) models, giving you greater access to newer vehicles and systems. Note: The FCA AutoAuth account is not included with the device. Users must register and pay separately through the official FCA AutoAuth website to access diagnostic functions for vehicles that require it. - Up to 8 Live Data Streams Graphing – Real-Time Graphing for Deeper Insight: This car scanner supports up to 8 live data streams simultaneously with intuitive, real-time graphing. Gain comprehensive insights into your vehicle’s performance, making it easier to spot issues, detect trends, and make informed diagnostic decisions with confidence.
- Comprehensive OBD2 Scanner with 16 Resets: The XTOOL D5S car code reader and vehicle reset tool provides an advanced diagnostic solution with 16 commonly needed reset functions, including Electronic Parking Brake Reset (EPB Reset), SAS, BMS Reset (Battery Test), Throttle Body Relearn, TPMS Reset, ABS Bleeding, Injector Coding, Gearbox Match, Suspension Adjustment, Headlight, Window Initialization, Crank Sensor Relearn and more. Equipped with CAN FD Protocol and FAC AutoAuth, the D5S obd2 scanner diagnostic tool ensures compatibility with a broad range of modern vehicles, allowing users to address common maintenance needs quickly. NOTE: Please Check the Compatibility before ordering.
- 4 Main System Car Scanner & Full OBD2 Diagnostics: The XTOOL D5S car code reader is ideal for home mechanics, DIYers, and professionals, providing access to Transmission/Engine/ABS/SRS systems to read DTCs, Live data can be displayed in text or up to 4 PID data graphs, along with full OBD2 diagnostics to check the engine light on, other obd2 issues and routine maintenance. This car diagnostic scanner ensures you can keep your vehicles in top condition, avoiding costly repairs or unexpected breakdowns. NOTE: Some vehicles display three systems after connection because the transmission and engine of some vehicles are integrated into one.
- Check Engine Code Reader & Real-Time Engine Monitoring: Whether you're a car owner, a DIYer, or run a repair shop, the XTOOL D5S obd2 scanner diagnostic tool makes engine diagnostics fast and frustration-free, reading and explaining trouble codes in seconds—no confusion. Check live data like fuel trim, 02 sensor voltage, RPM, and coolant temp to pinpoint mis~fires, rough idle, or sensor issues. After repairs, simply use the D5S check engine code reader and reset tool to turn off the check engine light and confirm the problem’s fixed—saving time, money, and unnecessary shop visits. - Note: If the check engine light comes back on, it indicates the original problem still exists.
- Portable Car Scanner for ABS and SRS: XTOOL D5S gives you peace of mind when ABS or airbag warning lights come on. It reads and clears ABS codes to help you fix brake sensor, traction control, or wheel speed issues, and supports ABS bleeding after repairs like caliper or master cylinder replacement. For airbag systems, it scans and clears SRS codes related to airbags, seatbelt tensioners, and crash sensors. Whether you're doing repairs at home or running a small shop, the D5S is a cost-effective solution for safety diagnostics. Note: If a fault code returns after clearing, it usually means the issue hasn’t been fully resolved. Please check the compatibility before ordering.
- Transmission Warning Light ON? Here’s the Transmission Diagnostic and Reset Tool You Need: The XTOOL D5S is more than just a basic car scanner—it’s an easy-to-use transmission diagnostic tool. From rough shifts to slipping gears, the D5S lets you read and clear transmission trouble codes, monitor real-time TCM data, and perform transmission resets after fluid changes or repairs. Whether you’re a hands-on car owner or a pro running a busy shop, this OBD2 scanner with transmission functions helps you catch problems early—saving you time, money, and future headaches.. Note: Clearing fault codes is equivalent to a reset on some vehicles, but not all. For help, contact XTOOL Tech Support.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations
- 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.