Technical Tip

96-14-05TT - Immobilizer Key/Key Remote Adaptation Test Plan

Transaction No:

2038198/14

Release date:

1/24/2020

Condition
ATTENTION:
THIS IS A TECH TIP, NOT A TECHNICAL BULLETIN.
TECH TIPS ARE NOT ASSOCIATED WITH WARRANTY CLAIMING.

Applicable Vehicles
Model(s)

Year

Eng. Code

Trans. Code

VIN Range From

VIN Range To

Golf, GTI, Golf R,
eGolf, Golf
SportWagen

2015-2020

All

All

All

All

Atlas, Tiguan
LWB

2018-2020

All

All

All

All

Jetta

2019-2020

All

All

All

All

Revision Table
Instance Number

Published Date

Version Number

Reason For Update

2038198/14

1/24/20

96-14-05TT

To include model year 2020
applicability.

2038198/1

8/22/14

96-14-05TT

Original publication.

Technical Background
To adapt keys, any immobilizer component including the Control Module for Emergency Call Module and
Communication Unit -J949- or a new identity, makes it necessary to complete the “Adapt Immobilizer” test plan.
Kessy Vehicles: Verify that the reader coil is removed from the steering column and the key is touching the reader coil
during key adaptation (Figures 1a – 1c). Bladed key vehicle, it is not necessary to remove the reader coil. The test
plan can be found under the ODIS Service Special Functions Tab (Figure 2) or by navigating to “Immobilizer
functions” under “Elect. Immobilizer 5A” after clicking the “Select self-test” button in the Test Plan tab (Figure 3). This
procedure adapts both the remote and immobilizer functions of the key.
Note:
Vehicle may not start and or have warning lights on cluster after immobilizer / key adaptation is completed. See figure
9 information in this tech tip after immobilizer / key adaptation for further instructions.
Prior to starting the test plan to adapt the immobilizer, the key positioning on the reader coil itself is critical. Monitor
MVB information in the immobilizer with the key touching the reader coil to verify a key ID is being seen.
Key ID MVB information may either be found under Address word 25 Immobilizer or Address word 17 Instrument
cluster depending on vehicles module protocol.

1

Technical Tip

96-14-05TT - Immobilizer Key/Key Remote Adaptation Test Plan

Transaction No:

2038198/14

Release date:

1/24/2020

Service
If the key ID is not being seen in the MVB reading, then rotate the key around the reader coil until the key ID is seen in
MVB information.

Possible key placements at Reader Coil

2

Technical Tip

96-14-05TT - Immobilizer Key/Key Remote Adaptation Test Plan

Transaction No:

2038198/14

Release date:

1/24/2020

Figure 2

Figure 3
3

Technical Tip

Transaction No:

2038198/14

Release date:

1/24/2020

96-14-05TT - Immobilizer Key/Key Remote Adaptation Test Plan

When prompted by the test plan, make the selection to Repair immobilizer (Figure 4).

Figure 4
Once the purchaser’s information is entered and valid login credentials are provided, the adaptation status of all
immobilizer components is displayed (Figure 5). Select “Complete/Continue”.

Figure 5

4

Technical Tip

96-14-05TT - Immobilizer Key/Key Remote Adaptation Test Plan

Transaction No:

2038198/14

Release date:

1/24/2020

Select “Yes” when prompted to perform key adaptation (Figure 6).

Figure 6
Use the + and – buttons to select the number of keys to be adapted, then select “OK” (Figure 7).

Figure 7

5

Technical Tip

96-14-05TT - Immobilizer Key/Key Remote Adaptation Test Plan

Transaction No:

2038198/14

Release date:

1/24/2020

Continue to follow test plan instructions to complete key adaptation (Figure 8).

Figure 8
Vehicle doesn’t start and or warning lights ON after immobilizer / key adaptation. Check for faults related to modules
that may no longer be coded (Figure 9).

Figure 9

6

Technical Tip

96-14-05TT - Immobilizer Key/Key Remote Adaptation Test Plan

Transaction No:

2038198/14

Release date:

1/24/2020

It will be necessary to recode all modules that are no longer coded. Code modules online under the special functions
tab, “Code online control module”. Modules may include, but not limited to ECM, ABS, TCM. The FES test plan may
need to be ran on the Gateway AW 19, select #2 “Re-create function” (Figure10).

Figure 10

Additional Information
© 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on
the latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make
changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

7