Ferrari North America
Technical Information

Date:
Bulletin #:
Campaign #:
Supersedes:
Section:

November 2019
2597
10

Model Type:
Monza SP2
Subject: Pre-Delivery Inspection – PDI procedures
Please find enclosed the procedures and list of inspections to be performed at all times before
the vehicle is delivered to the customer.
The following procedures must be performed exactly as indicated and in the order given,
providing the factory with the information requested.

- IMPORTANT This vehicle is built for track use only and cannot be driven on public roads. If you are
unable to perform procedures 30-35, then move the vehicle about the workshop or
parking lot in order to test the systems in question.

- IMPORTANT This Pre-Delivery Inspection (PDI) procedure may only be performed with a PC-Tester
DEIS updated to at least the following software version (or subsequent release):
-

Module
Module
Module
Module

0
1
2
3

Portal and Troubleshooting
DEIS Diagnostic software
Technical Documentation
Tools

54
86
12
8

Check the software number and, if necessary, update your DEIS Tester immediately.
After updating the DEIS, the first vehicle diagnostic cycle must be performed using a
cable connection.
Procedure.
1.

Visually inspect condition of vehicle paintwork; repair if necessary (use the specific
“Bodywork” form annexed on page 10).
© 2019. Ferrari North America, Inc.
Technical Department
www.ferrari.com

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
2.

If disconnected, connect the negative pole of the battery and reset the vehicle autoadaptive parameters (as described in paragraph F3.01 of the Workshop Manual).

3.

Activate Key-ON state (as described in paragraph F19.02 of the Workshop Manual), and
check which letter is shown on the DOT MATRIX display:
- If letter “P” (Park Lock) is on the display, go to point 5.
- If letter “N” (Neutral) is on the display, go to point 4.

4.

Re-enable the Park Lock – Gearbox lock device (as described in paragraph C2.07 of the
Workshop Manual).

5.

Remove the engine compartment cosmetic shields (as described in paragraph E3.03 of
the Workshop Manual); Perform the “Battery Certification” procedure (TI 2079 /
2230), and compile the relative form. If necessary, remove the battery from the vehicle
and charge using the “SLOW charge ” procedure (TI 2078).

6.

Using the DEIS tester, disable the “Logistic Mode” function with diagnostic cycle “150
Complete Logistic Mode” on the NBC ECU (Body Computer Node).

7.

Test the keys and the anti-theft system.

8.

Check that the daytime lights work correctly (depending on market).

9.

Check that the low beam headlights work correctly: also check that the AFS system
(adaptive front lights - if applicable) works correctly by turning the steering wheel.

10. Check the vehicle front lift (if present) is working: also check that the AFS system
(adaptive front lights - if applicable) works correctly. With the car raised, the height of
the headlight beam must be the same as with the car lowered.
11. Check that the high beam headlights work correctly.
12. Check that the brake lights work correctly.
13. Check that the turn indicators and license plate lights work correctly.
2
© 2019. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2597

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
14. Check that the backlighting of the door, dashboard and tunnel buttons is working
correctly.
15. Test the horn.
16. Check that the steering adjustment mechanism works correctly.
17. Check that the mechanical driver and passenger seat adjustment mechanism works
correctly.
18. Check that the electric parking brake (EPB) works correctly; test manual and automatic
modes.
19. Check that Hi-Fi / navigation system works correctly (if installed, see point 30); set the
relative roadside assistance numbers for your market.
20. Check coolant level and top off if necessary.
21. Check the brake fluid level and top off if necessary.
22. Check tire pressure / TPMS system calibration.
23. Check the tightness of the wheel studs with a torque wrench (as described in paragraph
D2.01 of the Workshop Manual).
24. Check that the tow hook can be fitted correctly.
Start the engine (as described in paragraph F19.02 of the Workshop Manual), and
perform the following:
25. Check that the air conditioning and heating system works correctly (static test).
26. Check that the electric rear view mirrors work correctly.

3
© 2019. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2597

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
27. Select reverse:
- check that the angle of the RH rear view mirror adjusts automatically;
- check function of the internal electrochromic mirror and the
electrochromic RH and LH rear view mirrors (if applicable).
28. Check that the front and rear parking sensors work correctly; check the rear and front
cameras (if present).
29. Using the DEIS tester, perform the “Cancel all DTCs from all ECUs” procedure from
the “Vehicle functions” menu.
Test drive.
30. Check that the navigation system works correctly (if applicable); set route before starting.
31. Test drive the vehicle (approx. 20 minutes).
32. Check that Stop&Start system works correctly.
33. While driving, check that the “Suspension damping decoupling” button and
“Manettino” dial on the steering wheel work correctly.
34. While driving, check that the air conditioning and heating system works correctly
(dynamic test).
35. For USA/CND Version only. Take the vehicle into a location with a clear view of the sky
and activate the Sirius subscription as per FNA 165
Return to workshop.
36. Check the engine oil level (engine warm and at idle speed) and top off if necessary (as
described in paragraph B8.02 of the Workshop Manual).
37. With the DEIS tester, check that the VIN number read with the tester matches the VIN
number of the vehicle; if necessary, the VIN number read with the tester may be modified
4
© 2019. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2597

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
using the “100 VIN Writing” diagnostic function (password-protected) on the NCM
ECUs (RH and LH engine control units).
38. Check and cancel the errors on all ECUs.
39. Enter the warranty start date (Check that the language setting on the TFT display is
correct).
40. Disconnect the battery , wait 30 seconds and reconnect (as described in paragraph
F3.01 of the Workshop Manual). Restore the self-adaptive vehicle parameters (as
described in paragraph F3.01 of the Workshop Manual).
41. Perform the “SCAN OUT” procedure from the “Vehicle functions” menu with the DEIS
tester before carrying out any further diagnostic operations.
42. Remove the aerodynamic undertray from the vehicle (as described in paragraph E3.01
of the Workshop Manual).
43. Visually check for coolant and/or oil leaks in the underbody area and engine
compartment.
44. Visually inspect engine compartment lines.
45. Visually inspect the engine compartment wiring harnesses.
46. Visually inspect underbody lines.
47. Visually inspect exhaust pipe.
48. Visually inspect fuel tank.
49. Visually check correct assembly of: Suspension units, steering box and rear axle shaft
flanges.

5
© 2019. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2597

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
50. Check visually that the following are fitted/tightened correctly: vehicle ground point,
engine ground point on chassis and gearbox ground on chassis.
51. Visually inspect condition of brake pads and discs (DO NOT remove wheels).
52. Check condition of tires and wheels.
53. Refit the complete aerodynamic undertray and cosmetic engine compartment shields (as
described in paragraphs E3.01 of the Workshop Manual).
54. Check that the door and lid locks work correctly; adjust if necessary.
55. Check that the fuel filler flap and luggage compartment emergency release mechanisms
work correctly; adjust if necessary.
56. Visually inspect condition of leather upholstery; repair if necessary.
57. Thoroughly clean interior and wash car.
58. Ensure that the vehicle is delivered complete with the following:
identification and type approval plates
bag with waterproof cover
tool kit
on-board documentation (Owner's Manual, Quick Reference Guide, Warranty
Booklet, Safety Device Booklet and Battery Conditioner Quick Guide card), second
vehicle key and code card, and any material related to options.
59. Check that the battery conditioner provided with the vehicle works correctly, referring to
the relative manual.

6
© 2019. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2597

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Ferrari North America
- IMPORTANT Confirm that the operations listed above have been carried out correctly with the “PreDelivery Inspection - PDI” form (enclosed on pages 8 and 9), compiled in full and signed
by the Aftersales Manager of your Authorized Ferrari Dealer.
After completing an inspection, ALWAYS open an ROL (Red On Line), indicating “PDI
Form Info” as the cause, and attach the duly completed “PDI Pre-Delivery Inspection”
form, together the completed Checklist and body forms from page 8-10, the “Battery
state certification” form (TI 2079 / 2230), and a scan-out. The procedure for “Testing
zero load electric absorption” is given in paragraph F3.11 of the Workshop Manual).
You will also be required to open a separate individual ROL with the description "PDI
Fault Info" for each fault encountered during the inspection procedure, indicating the
respective operation number as cited in the “PDI Pre-Delivery Inspection” form; Attach
all necessary documentation, including photographs if needed.

7
© 2019. Ferrari North America, Inc.
Technical Department
www.ferrari.com

TI-2597

All rights reserved. Reproduction or translation in
whole or in part is not permitted without
authorization from the publisher. Printed in USA.

Pre-Delivery Inspection - PDI form

Page 01 of 02

Model

Updated on
September 2019

Chassis number:

Dossier creation date:

Job order no.:
Notes:

Description of inspection / operation:
1. - Condition of vehicle paintwork.
2. - Connect battery and reset vehicle parameters.
3. - Check Park Lock device.
4. - Reset Park Lock device.
5. - “Battery Certification” procedure.
6. - Disable “Logistic Mode”.
7. - Test keys, etc.
8. - Daytime running lights.
9. - Low beam lights and AFS (if present).
10. - Check vehicle front lift system (if applicable).
11. - High beams.
12. - Stop lights.
13. - Turn indicators and number plate lights.
14. - Lights of door, dashboard and tunnel buttons.
15. - Horn.
16. - Steering wheel adjustment.
17. - Seats / Electric seats; test settings memory function (if
applicable).
18. - Electric parking brake (EPB); manual/auto.
19. - Hi-Fi system / Navigation system (if applicable) (see point
30).
20. - Coolant level.
21. - Braking system fluid level.
22. - Tyre pressure / calibrated pressure on TPMS.
23. - Tightening of wheel stud bolts.
24. - Tow hook.
25. - * Air conditioning and heating system (static test).
26. - *Electric rear-view mirrors.
27. - *RH or LH rear view mirror – with reverse selected.
28. - *Parking sensors.
29. - Cancel all DTCs from all ECUs.
30. - Navigation system: Set a route (if applicable).
31. - Test drive (20 min.).
32. - Stop&Start (functional test).

Performed
OK

Performed
NOT OK











































































R.O.L. N°
(if NOT OK)

(*) With engine running
Page 02 of 02

Technical Service Department
Page 8 of 10

Pre-Delivery Inspection - PDI form
Model

Updated on
September 2019

Description of inspection / operation:

Performed
OK

Performed
NOT OK





























































33. - Suspension damping decouple button and “Manettino”.
34. - Air conditioning and heating system (dynamic test).
35. - for USA / CND ONLY _ SDARS activation.
36. - Engine oil level (warm engine – at idle speed).
37. - Verify VIN from NCM parameters.
38. - Delete ECU errors.
39. - Enter warranty start date.
40. - Disconnect and reconnect the battery.
41. - Perform SCAN OUT procedure.
42. - Remove aerodynamic floor.
43. - Water and/or oil leaks in vehicle underbody .
44. - Engine compartment lines.
45. - Engine compartment wiring.
46. - Underbody lines.
47. - Exhaust pipe.
48. - Fuel tank.
49. - Visual inspection: Suspension components, etc.
50. - Visual inspection of earth connections: vehicle/engine and
gearbox on chassis.
51. - Condition of brake pads and discs (DO NOT remove wheels).
52. - Condition of tyres and wheel rims.
53. - Refit flat bottom and the engine compartment panels.
54. - Door and lid locks.
55. - Fuel filler flap emergency opening.
56. - Condition of vehicle's leather upholstery.
57. - Clean interior and wash car.
58. - Material provided with vehicle: Tool kit, etc.
59. – Functional test of battery maintainer

Task performed by (Dealer):
Technical Manager:
First name
(Print)

Last name

(Print)

Company stamp

Full signature
Vehicle delivery date:
Technical Service Department
Page 9 of 10

R.O.L. N°
(if NOT OK)

Bodywork Form

Issue

Technical Service Department
Page 10 of 10