NHTSA ID Number: 10168569
Manufacturer Communication Number: 15-230-18R
TSB/Document Date: 2019-12-03
Summary
This bulletin provides troubleshooting steps to follow when diagnosing customer concerns involving Bluetooth (BT) functionality. Please start by completing the Harman Investigation Guide Questionnaire as it gathers important details which will help with diagnosis and will be required should the condition not be resolved by this troubleshooting. While completing the questionnaire, follow the question flow based on the customer concern. Answer each related question noting the results to each in detail while performing the diagnostics. Review the entire bulletin before beginning in order to understand the flow for the listed concern. Please apply the information captured in the checklist to the Harman Investigation Guide Questionnaire. If the concern you have is not listed, check the Service Manual
+?Infotainment (Diagnostics) - Diagnostics with Phenomena+? section as a starting point.
ATTENTION:
CLAIMS PERSONNEL q
IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
SERVICE MANAGER
© 2018 Subaru of America, Inc. All rights reserved.
GENERAL MANAGER q
PARTS MANAGER
q
q
SERVICE BULLETIN
APPLICABILITY: 2017-20MY Impreza
2018-20MY Crosstrek
2018-19MY Legacy and Outback
2019-20MY WRX and WRX STI
2019-20MY Ascent
2018-20MY BRZ
2019-20MY Forester
NUMBER: 15-230-18R
DATE: 08/21/18
REVISED: 11/15/19
SUBJECT: Harman Audio / Infotainment: Troubleshooting
Bluetooth® Functionality Concerns
INTRODUCTION:
This bulletin provides troubleshooting steps to follow when diagnosing customer concerns
involving Bluetooth (BT) functionality. Please start by completing the Harman Investigation Guide
Questionnaire as it gathers important details which will help with diagnosis and will be required
should the condition not be resolved by this troubleshooting. While completing the questionnaire,
follow the question flow based on the customer concern. Answer each related question noting the
results to each in detail while performing the diagnostics. Review the entire bulletin before beginning
in order to understand the flow for the listed concern. Please apply the information captured in the
checklist to the Harman Investigation Guide Questionnaire. If the concern you have is not listed,
check the Service Manual “Infotainment (Diagnostics) - Diagnostics with Phenomena” section as a
starting point.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts
with performing quality repairs.
1) Always confirm the condition as reported by the
customer.
2) Visit the Subaru Technology page on the Subaru.
com website to verify smart phone compatibility.
(https://www.subaru.com/engineering/
technology.html)
Continued...
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
Bulletin Number: 15-230-18R; Revised: 11/15/19
Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.
Page 1 of 13
As shown in the image above, the iPhone 8 may have an issue with Phonebook Download (single
contact) and SMS send functions (not shown). When the customer reports a condition involving
those features, STOP as there is no further Head Unit (HU) troubleshooting required. The issue is
linked directly to their smart phone’s compatibility. There are some cases where a particular smart
phone’s compatibility has not been fully or at all tested.
For those smart phones, BT functionality operation could be unreliable. These cases are not an
indication of a Head Unit (HU) malfunction. See the example shown in the image below.
3) It is also recommended to verify the customer’s phone setup is not causing BT related issues.
a. For any kind of car connection issue, it is important to make sure that the “Do Not
Disturb” feature is turned OFF. Some customers have not been able to shut off the “Do
Not Disturb” feature while connected to their vehicles. By default, this setting is set to
manual and must be activated before enabled.
TIP: It may be easier to disconnect and remove all Bluetooth device settings before upgrading the
device then, start over from scratch. This may save significant time in troubleshooting.
b. Can the condition be duplicated? If so, please provide the steps necessary to reproduce
and if possible, a video showing the steps and concern. It is important to know if the BT
connection is not made at start up or if the connection is lost at some other point during
operation.
i. If the BT connection drops during operation, confirm the device is in the paired
device list located under Settings > Phone. See image below.
ii. Verify the head unit is still listed as a paired device on the phone.
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 2 of 13
iii. If the device is not listed, try to manually reconnect through the phone settings
menu: Settings > Phone > Select the paired phone and select Connect.
iv. If the condition is still present, try confirming it with a similar model phone (capture
phone model and OS version).
v. Follow the Service Manual basic diagnostic procedure for “BLUETOOTH
CONNECTION CANNOT BE ESTABLISHED”.
4) This section addresses concerns with Bluetooth Phonebook or SMS synchronization as
referenced in 2) above.
a. Confirm the phonebook / SMS access request was granted when phone was paired to the
HU. When the pairing procedure is performed and the device is connected, the phone
may prompt the user to accept access for phonebook. The HU will prompt to initiate
phonebook download. Accept this pop up by pressing “Download”.
b. Phone behavior may differ between models and OS versions and between Android
phones (i) and Apple iPhones (ii):
i. Android phone
1. Android phone will prompt user on the phone for
phonebook access as shown to the right.
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 3 of 13
2. Also, in the case of Android phones, a second pop-up
will appear requesting access to SMS messages.
ii. Apple iPhone:
1. The iPhone will download the phonebook after
pressing “Download” on HU if the Sync Contacts
option is enabled. NOTE: Some versions of iOS will
prompt the user for phonebook access as shown to the
right.
2. For iPhones, after pairing is complete, access must
be enabled on the phone for SMS. To do this, go to
Settings > Bluetooth > Select the paired HU labeled
“Subaru BT” and make sure both Sync Contacts and
Show Notifications are enabled.
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 4 of 13
3. Once enabled, the iPhone must be disconnected then reconnected for the
changes to apply for SMS download ONLY. See section 5a “How to Pair an
Apple Device”.
c. If the device is already paired and connected, confirm the Phonebook Download option
is enabled. To do this go to Settings > Phone, select the paired phone and enable
Phonebook Download as shown below.
NOTE: The device may still require performing Steps a. and b. above after enabling Phonebook
Download on the HU.
If the phonebook or messages can still not be accessed, go back to the phones Bluetooth settings and
select the gear (Settings) icon next to your vehicle’s device name. Ensure all settings are enabled.
5) This section will help to assure Android and Apple phones are properly paired.
a. How to pair an Apple device:
i. Go to Settings on the vehicle infotainment icon
screen.
ii. Select “Phone”
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 5 of 13
iii. Select “Add Device”
iv. This screen will be displayed when pairing mode is in progress. Make note of the
“Device Name:” (Subaru BT).
v. On the iOS/Apple device, go to settings. Location on home screen will vary.
vi. Select “Bluetooth”
vii. Select “Subaru BT” or whatever the device name is from step iv.
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 6 of 13
viii.
Select “Pair”
ix. Select Allow to “Allow Contacts and Favorites to Sync?”
x. On the vehicle screen, select “Download” phonebook contacts.
xi. On the iOS/Apple device, the vehicle’s Bluetooth should now be listed under
Bluetooth settings. Select the blue “i” next to the device name (Subaru BT).
xii. Confirm “Show Notifications” and “Sync Contacts” are enabled.
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 7 of 13
xiii.
At this point, the iOS/Apple device is paired. The vehicle may need to be restarted
to fully complete the pairing process so messaging and other features work
correctly.
xiv.
If smartphones are not connecting with the HU via Bluetooth, try it again after
removing all the connection history from the phone. This may help the
smartphone and HU “find each other” easier when performing the Bluetooth
connection process.
b. How to pair Android Device:
i. Go to Settings on the vehicle infotainment icon screen.
ii. Go to the “Phone” page
iii. Select “Add Device”
iv. This screen will be displayed when pairing mode is in progress. Make note of the
“Device Name:” (Subaru BT).
v. On the Android device, go to Settings. This step will vary by Android device.
Settings can always be found under Apps. On newer Android devices, Apps is
opened by swiping UP from the bottom of the screen.
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 8 of 13
vi. Select “Connected devices” or “connections”.
vii.
Select “Bluetooth”
viii.
At this step, either select “Pair new device” or, the phone will already begin
showing nearby devices to add.
ix. Select “Subaru BT” or whatever the device name is from step 4.
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 9 of 13
x. Select “PAIR” and ensure “Allow access to your contacts and call history” are
enabled (checked).
xi. Select “YES” to the Message access request” pop up.
xii.
On the vehicle screen, select “Download” phonebook contacts.
xiii.
At this point, the Android phone should be paired and ready to use.
xiv.
If smartphones are not connecting with the HU via Bluetooth, try it again after
removing all the connection history from the phone. This may help the
smartphone and HU to “find each other” easier when performing the Bluetooth
connection process.
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 10 of 13
6) This section addresses concerns with BT call handling.
a. Capture the steps required to reproduce the concern. If possible, record a video showing
the steps and the condition. Please note the model, OS version, and service carrier of the
customer’s phone.
b. For concerns regarding holding calls and / or swapping calls (call waiting), please note
CDMA networks do not support this functionality. Some phones may have the ability
to perform these actions internally but in general, CDMA carriers (such as Sprint or
Verizon) do not support these features.
c. For concerns related to the audio quality, verify microphone operation. See figure below
for Line Diag display of Microphone check.
d. Follow the Service Manual basic diagnostic procedure for SOUND DOES NOT COME
OUT FROM THE SPEAKER. See image below for Line Diag display of Audio Check.
e. If the concern persists, swap a known good HU into the problem vehicle. If component
swap addressed concern, request exchange for the suspect component.
IMPORTANT CAUTION: Always disconnect the Telematics Data Communication Module
(DCM) BEFORE any swapping of head units. DCMs must NEVER be swapped or the customer’s
services will not function and DCM replacement may be required to resolve.
7) If the above diagnostics and procedures do not resolve the customer’s concern with Bluetooth
functionality, complete a fresh Harman Investigation Guide Questionnaire documenting the
customer’s concern and the results of each diagnostic step in this bulletin. If possible, capture
a video of the condition then contact the SOA Techline to review the next steps. Techline will
request you send the completed questionnaire, step-by-step bulletin test results and any videos
of the condition.
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 11 of 13
BLUETOOTH® FUNCTIONALITY CONCERN CHECKLIST
Repair Order Date:
Vehicle Identification Number (VIN):
1. Condition confirmed as reported by the customer?
NO:
YES:
Concern details:
Phone details: Make
Model
OS
Carrier
2. Is the phone compatible?
NO:
YES:
3a. Is the phone listed among paired devices on the head unit display? NO: YES:
3b. Is the vehicle listed among paired devices on the phone?
NO:
YES:
4. If applicable, is Phonebook Download enabled on the head unit?
NO:
YES:
5a. If applicable, perform Line Diag test:
NO:
YES:
5b. Microphone test passed?
NO:
YES:
5c. Speaker test passed?
NO:
YES:
5d. Tested using a like vehicle?
NO:
YES:
3c. Head Unit software version:
Continued...
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 12 of 13
WARRANTY / CLAIM INFORMATION:
For vehicles within the Basic New Car Limited Warranty period or covered by an active Subaru
Added Security Gold plan, this repair may be submitted using the following claim information:
Labor Description
Labor Operation #
Labor Time
HARMAN BLUETOOTH FUNCTION NOT COMPATIBLE
A850-803
0.3
HARMAN BLUETOOTH TROUBLESHOOTING
A850-805
0.8
Fail Code
H/U Type
ZRQ-43
Base, Mid &
High
IMPORTANT REMINDERS:
•
SOA strongly discourages the printing and/or local storage of service information as
previously released information and electronic publications may be updated at any time.
•
Always check for any open recalls or campaigns anytime a vehicle is in for servicing.
•
Always refer to STIS for the latest service information before performing any repairs.
Bulletin Number: 15-230-18R; Revised: 11/15/19
Page 13 of 13
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 📌【We are Here for You】Dear valued customer, please be...
- 🚀【5X Faster Next-Level Hardware, Same as MK900/ MX...
- 🔥【3000+ Active Tests = MK900/MK900BT but...
- 📢【2026 U.S. Version, All-in-One as MK808S/ MK808Z...
- 🔥【28+ Hot Services for 150+ Brands】Same as MaxiCOM...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 15-230-18R
Replacement Service Bulletin Number:
MFR Communication Date: 2019-11-15
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT ADAPTIVE/MOBILITY
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.