way switching system. These map lights are wired into the headlight switch and are powered off of the chassis battery
only, not the auxiliary battery like the rest of the interior lights.

FIRST OPTION is to have the headlight knob tumed to the centre the map lights will be tumed on. When you open
the doors to the motorhome these lights will come on and shut off when you shut the door,

SECOND OPTION is to have the headlight knob tumed all the way to the left - this lets you tum the map lights on and
off by using the map light switch while the doors are closed. NOTE: DO NOT LEAVE THE KNOB IN THIS POSITION
FOR AN EXTENDED PERIOD OF TIME IF YOU ARE NOT DRIVING, FOR THIS WILL DRAIN AND KILL THE
CHASSIS BATTERY.

THIRD OPTION is to have the headlight knob tumed all the way to the right - these lights will not come on when your
doors open. NOTE: this is the position that this should be left when not driving.

REFRIGERATOR - NORCOLD AND DOMETIC

Your DOMETIC refrigerator is designed for 3-way operation, using 12 voit DC, 110 volt AC and LP gas power. When
the refrigerator is switched to AC or DC, the ammonia/water mixture is heated by a heating element instead of a bumer.

When your motorhome is stationary, it should be levelled for your refrigerator to provide the proper cooling. A bubble
level should be placed on the freezer shelf to check the refrigerator for levelness. If the refrigerator is not level you
may have improper cooling.

For LP gas operation, tum the selector switch to gas and follow the instructions on the fndge for lighting. Tum the
fndge thermostat to the highest temperature that will still provide adequate refrigeration. For 110 volt AC operation,
make sure the power cord is connected and switch the selector switch to AC power. For the 12 volt DC operation
setting, power is now provided by the auxiliary battery. However, the 12 volt power should not be used when stationary
in order to prevent battery drainage.

NOTE the refrigerator should be tumed to 12 volt when the vehicle will be in motion and the LP gas must be tumed
off.

See manufacturer's operating manual for complete operating instructions and maintenance procedures.
For operating instructions for the remainder of your appliances, please see each respective manufactures operating
manuals.

MOTORHOME INTERIOR

TV AND VCP (optional)

If your motor home is equipped with TV and VCP components, you will find these located in the rear
entertainment centre cabinet or in the front overhead console cabinet (Excel MP or Lexor MP). These two
components are powered by a 12 volt power source.
* Note: Your VCP is a player only - it will not record.

REAR ENTERTAINMENT CENTRE:

In the rear entertainment centre you will find the TV is positioned on a swing out base. To swing your TV out
for viewing from the front, slide the locking bolt located in the door above the TV up. This will release the TV
pivot and allow the TV to swing out towards you.

With your TV swung out you will notice that you have access to your antenna booster, your cable splitter and
your cable/antenna slide switch.

*Note: When travelling it is recommended that your TV remains in the locked position.

To remove the VCP from the cabinet, (1) swing your TV to a full open position; (2) remove the two screws
located on the underside of the VCP shelf, close to the front of the VCP; (3) slide the VCP from the cabinet.

FRONT CONSOLE ENTERTAINMENT CENTRE:

In the front entertainment centre you will find the TV located in the centre cabinet and the VCP above the
passengers seat in the console cabinet. You will find the antenna booster and cable slide-switch located in the
drivers console cabinet.

To remove your TV remove the screws located under the snap buttons on the side of the TV cabinet. Slide the
TV forward and remove it from the cabinet.

To remove your VCP from the console: (1) remove the console door and prop; (2) remove the screws through
the VCP base located on the left and right hand side of the VCP; (3) remove the plastic side caps from the VCP
base; (4) slide the VCP and base through the console opening.

* Note: TV and VCP in the front console will not operate while vehicle is in motion.

MOTORHOME INTERIOR

COUNTER TOP EXTENSIONS

Slide out Extension:

On the EXCEI-TD or RD and the LEXOR-TD or RD you will find a kitchen countertop slide out located above
the entry handrail on the kitchen end gable.

Slide the oak faceplate out toward the passenger seat. Place the sink cover between the silver slides and oak
faceplate in the groves provided on the bottom side of the sink cover.

Flip up Extension:

On the EXCEL-MP and LEXOR-MP you will find a self locking flip up countertop extension located on the rear
side of the passengers rear partition. Simply lift this to 90 degrees and it will lock into place. To release the lock,
simply push the two lock release buttons located at the end of the supports under the extension.

SWIVEL SEATS

Method #1 to swivel your captain's chairs:
Slide your seat to the farthest forward position. Move the backrest into the farthest upright position. Move the
backrest into the farthest upright position. Swivel the chair with the backrest toward the outside of the unit.

Method #2 to swivel your captain's chairs:
Slide the chair to the farthest back position. Swivel the chair with the seat of the chair towards the outside of

the unit.

SLEEPER CHAIRS (Lexor MP or Excel MP only)
* Note: Use method #2 for swiveling captain's chairs.

Driver Side:
With the captain's chair in the swiveled position with the backrest toward the centre of the unit, slide the sleeper
seat Slide to a full forward position. Lift the front of the sleeper chair moving it to the flat laying position.

Passenger Side:
With the captain's chair in the swivel position with the backrest toward the front of the unit, slide the sleeper
seat to a full forward position. Lift the front of the sleeper chair moving it to a full layout position.

r # | .
Cm NG
aie eg PN ae
fy er aye a
23

MOTORHOME INTERIOR

TD KING SIZE BED ASSEMBLY

1. Remove the night table from between the two twin beds and store underneath the rear seat compartment
accessed from the exterior rear door.

2. Remove the support boards which are stored underneath both twin beds. Place these boards along the oak
support rails which are along the sides of the twin beds.

3. Place the four backrest cushions in between the twin beds on the Support boards to complete the king size
bed.

Y o

z

6 | 6

= fa
PASSENGER'S B 6 | DRIVER'S
SIDE = a SIDE
SINGLE a | SINGLE
BED if i BED

S| 8

a a

SINGLE BED ASSEMBLY

To make up the front single beds in the PLEASURE-WAY Excel-MP and Lexor-MP models only, you first swivel
the front captain’s chair towards the outside so that the backrest is in the middle of the coach. The second
Step is to slide the rear sleeper seat all the way forward. Then grasp the seat from the front just under the seat
cushion and in a lifting pulling motion, pull the seat forward and the backrest will go down. This will give you
the make up of the single bed.

ELECTRIC SOFA BED

Your electric sofa is powered by 12 volt DC power supplied from your auxiliary battery. To convert your sofa to
a bed you must first slide the seat forward by pressing the switch located on the side of the TV cabinet. To lay
the bed down you must press the other switch located on the TV cabinet until the sofa is fully reclined. Reverse
the process to set the sofa upright again.

FTVIVVDDDVVPHADDDPRDDPPEDEDDDDPDDADDRAR RARER ABDIRIGTAVIA
MOTORHOME INTERIOR

TS BED LAYOUT

The TS unit is unique in that it has 3 possible bed lay-out position: King size, double, or two single beds.

A) King Size Bed:

1) Bring the power sofa forward into a full lay-out position.

2) Move the driver ottoman seat in so that the oak blocks on the bottom of the Cushion are in front of the face
frame.

3) Place the cushion support board (found in the front closet) between the oak cushion blocks on the driver’s
side supported by the oak rails on the passengers and drivers side.

4) Place the black rest cushions on the support board to fill in the space between the two ottoman cushions.

5) In the Excel TS move the passenger's ottoman seat out so that the back cushion block is in front of the
face frame and the front cushion block is behind the face frame.

POWER SOFA
BACKREST
POWER SOFA
SEAT
PASSENGER PASS DRIVER DRIVER
OTTOMAN OTTOMAN | OTTOMAN OTTOMAN
SEAT BACKREST | BACKREST SEAT

MOTORHOME INTERIOR

B) Double Bed:
1) Bring the power sofa into a full layout position - sleep across the unit using only the power sofa bed.

C) Two Single Beds:

1) Bring the power sofa into a full layout position.
2) Remove the ottoman backrest cushions,

} '

1 i

POWER SOFA I

, BACKREST I

J !

; j DOUBLE
i \ BED
' POWER SOFA i

SEAT
I 1
! |
PASSENGER DRIVER
OTTOMAN OTTOMAN
SEAT SEAT
[——— SINGLE —_¥ [-— SINGLE —

MOTORHOME INTERIOR

L-SHAPED BED ASSEMBLY

1. Remove the support board which is stored behind the passenger’s side backrest cushion. Place this board
across the support rail on the drawer cabinet below the entertainment centre and on front of the sofa bed.

2. Remove the two small seat cushions and the passenger's side backrest cushion and set aside.

3. Slide the long seat cushion forward to the front of the bed. Lay the long backrest cushion down at the rear
of the bed leaving a space along the middle (except Excel-RD and Excel-MP models). On the Excel-RD
and Excel-MP models, slide the long rear backrest cushion tight to the seat cushion now in the front.

4. The passenger's side backrest cushion and the larger of the two remaining seat cushions are placed in the
middle to complete the bed. (except Excel-RD and Excel-MP models). On the Excel-RD and Excel-MP
models, the passenger's side backrest cushion and the smaller of the two remaining seat cushions are
placed in the rear space next to the rear wall and backrest cushion to complete the bed. There is one
cushion not being used when the sofa is in this bed position.

SEAT SEAT

BACKREST CUSHION CUSHION | CUSHION

BACKREST CUSHION

BACKREST CUSHION

BACKREST CUSHION SEAT CUSHION

SEAT CUSHION SEAT CUSHION

MODEL: LEXOR RD and LEXOR MP MODEL: EXCEL-RD and EXCEL-MP

COACH SPECIFICATIONS

MODEL MODEL MODEL MODEL
and FEATURES LEXOR MP LEXOR TS LEXOR AD LEXOR TD

Dometic 3-Way Refrigerator (3 cu. ft.)
Sanyo Microwave Oven
2-Burner LP Stove
Suburban 16,000 BTU Auto Ign. Furnace
Thetford Flush Toilet
Shur Flo Demand Water System
Suburban 6 Gal. Auto Ign. Water Heater
Interior Height 6'
Medicine Cabinet
Large 2nd Sink
Shower
Smoke Detector
CO Detector (with Generator or Gen Ready only)
Fire Extinguisher
LP Detector
Fan Tastic Fan
Slide Out Auxiliary Battery
110V/12V/45 amp Convertor
Monitor Panel
Fresh Water Tank 114 L 30 U.S. Gal.
Grey Water Tank 91 L 24 U.S, Gal.
Black Water Tank 45 L 12 U.S. Gal.
Propane Tank 30 L 8 U.S. Gal.
Locking Fresh Water Fill
Captains Chairs Swivel & Recline
Rear Livingroom/Double Bed Area (54" x 72°)*
Twin Beds (26" x 74", 26" x 67")* King (74 x 74"/67")"
Rear Power Sofa Area (43° X 72")*
Hehr Awning Style Windows
Extra Cocktail Table
Sleeper Seats
Rear Component Compartment
Continental Spare Tire Carrier
interior Golf Club Storage
Spare Trunk (N/A with Generator)
Padded Engine Cover
Porch Light
Cable TV Hook Up
Hide-A-Tenna TV Antenna
Water Heater By-Pass
Fiberglass Running Boards
Exterior Storage Compartment
Rear Air Ride Suspension
Auxiliary Battery Disconnect
Slide Out Counter Extension
Flip Up Counter Extension

SISISISTSISTST SIS I SENT SLATS ESAT [ada tal sia dadala dads

N/A

NISISISTSINISIS [SINT STS TAs is [aisialsdslsdadsdalacds lato lola
SINTETE| S| S| STS [s] sia tsdadatadsda la] sdadatadsiadaladadc tals

SISISISTSTETETSISISTSTSIS [ST ST SN SE [sts [sta[s [zis ta siaiata tats ls
§

NINES

NINISTNIST ST SYS
SISISTSTSTSTSISISTS | SIRI SIS IE

z
>
SPSISISISTSTSIST STS TSISTE] Sts

\
z
SISISISTS[STSISTST NIST S [sis [3/2] 8] s

$

LEGEND: V = Standard — N/A = Not Available
* Note: Rear living room with a power sofa, the cushion area is smaller than the bed area.

SIVVVIVFIDPIAANA4B999474 49 40 ANADAAADRAAAANRAAAA BWW BMBWAD AH ee
GOACHISPECIFICATIONS MODEL MODEL MODEL MODEL
and FEATURES EXCEL MP EXCEL TS EXCEL RD EXCEL TD

Dometic 3-Way Relrigerator (3 cu. tt.)

Sanyo Microwave Oven

2-Burner LP Stove

Suburban 16,000 BTU Auto ign. Fumace
Thetiord Flush Toitet

Shur Fio Demand Water System

Suburban 6 Gal. Auto Ign. Water Heater
Interior Height 6’

Medicine Cabinet

Large 2nd Sink

Shower

Smoke Detector

CO Detector (with Generator or Gen Ready only)
Fire Extinguisher

LP Detector

Fan Tastic Fan

Slide Out Auxiliary Battery

110V/12V/45 amp Convertor

Monitor Panel

Fresh Water Tank 114 L 30 U.S. Gal.

Grey Water Tank 91 £ 24 U.S. Gal.

Black Water Tank 45 L 12 U.S. Gal.

Propane Tank 30 L 8 U.S. Gal.

Locking Fresh Water Fill

Captains Chair's Swivel & Recline

Rear Livingroom/Double Bed Area (54” x 79")°
Twin Beds (27.5* x 74", 27.5" x 67°)* King (79 x 747/67")*
Rear Power Sota Area (43° X 79°)*

Hehr Awning Style Windows

Extra Cocktail Table

Sleeper Seats

Rear Component Compartment

Continental Spare Tire Carrier

Interior Goll Club Storage

Spare Trunk (N/A with Generator)

Padded Engine Cover

Porch Light

Cable TV Hook Up

Hide-A-Tenna TV Antenna

Water Heater By-Pass

Fiberglass Running Boards

Exterior Storage Compartment

Rear Air Ride Suspension

Auxiliary Battery Disconnect

Slide Out Counter Extension NiA
Flip Up Counter Extension 7

NESTEIEISISISTST STS TS [SiN tsi ds [adalat dc dcdalc tals [alata ls

N/A

SISISTSES[SISTSISTELETS [SISTINE SPST STS [ a sada da dade f2 tats tedsts[a fa fats

$

SIN TRIS TNE

STNTSTSTSISTSTSTSTSISTEISTSTELSISTSTS IETS ESTs sista dst ats [ada [ada tod fos fe lla falda [ada
STSESTSTSTSISTSISTSTSTSTSIST ETSI STELS TELS [STS [SES T Ss tata dato la tata le lofted deff dc fa dx

EISISISTSISTST STATS [STATE IS fs

S
z
>

LEGEND: ¥ = Standard —_N/A = Not Available
* Note: Rear living room with a power sofa, the cushion area is smaller than the bed area.

is are id -
‘ee ee ee ls Mk
MON Ios a a LA
29