NHTSA ID Number: 10164633
Manufacturer Communication Number: SC-19-97
TSB/Document Date: 2019-09-10
Summary
The reason for this software update is to update various controllers. All the included Proterra Catalyst E2 vehicles require a change to the software/configuration for the following items: Battery Pack
Software, Charge Controller, ESM Software, Powertrain Controller, DWP/Dash Software, and Body Controller (ZR)
ISSUE DATE:
SERVICE BULLETIN SUBJECT:
VINs or MODELS AFFECTED:
COMPLETE BY:
SERVICE CAMPAIGN #:
8/14/2019
E2 Ver 1 Software Verification and Update
Catalyst 40 E2 with Rooftop BTMS
Next Available Service Opportunity
SC-19-97
NOTICE! It is expected that this process may require up to 3 hours per bus. Please
schedule appropriately to minimize vehicle downtime.
VEHICLE SOFTWARE VERIFICATION AND UPDATE
Description
The reason for this software update is to update various controllers. All the included Proterra Catalyst
vehicles require a change to the software/configuration for the following items:
•
•
•
•
•
•
•
Battery Pack Software
Charge Controller
ESM Software
Powertrain Controller
DWP/Dash Software
Body Controller (ZR)
Verify Only – Traction Motor Inverter Firmware Version
Summary of Software Changes
This update is to verify the latest software versions are installed for all controllers on the vehicle.
•
•
•
•
•
•
Battery Pack Software
o Improved recovery from INTCAN CAN Errors
o Additional Range Modes to allow for higher resolution SOH updates
o Balancing disabled during fast charge to prevent temperature de-rates to charging
o HVIL improvements to prevent sudden loss of power when only one string is enabled
Charge Controller
o Improved high power charge handling
o Broadcast of version numbers and EVSE parameters on CAN
ESM Software
o Improved SOC calculations and low voltage performance
Powertrain Controller
o Hill hold improvements
o Updates to enable 315 tire installation
DWP/Dash Software
o Added icons
Body Controller (ZR)
o Added support for new dash content
o Hill hold feature improvements
▪ New feature when upgrading from pre-40.26:
• Press-to-set hill hold activation and audible hill hold alert (if enabled)
o Added features for Auxiliary heating (fuel fired heater) system
o Support for cabin HVAC pre-conditioning (if supported by vehicle telemetry system)
o Customer-requested updates
▪ ADA chime to discrete output
▪ Aux Heat disable while charging feature
2|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Tools/Programs Required
Tools Required:
• Laptop Computer
• K-line USB Adapter (dash programming)
• USB to Serial Adapter (dash programming)
• Proterra OBD Breakout cable “Octopus”
• PCAN USB dongle
• Nexiq USB-Link or USB-Link 2
NOTE: IT IS NOT PERMITTED to use the Logena Service tool to perform the Body Controller
software update: this tool has been obsoleted. This tool does not maintain configuration
information and may result in unsafe/undesirable vehicle operation if used to flash body
controller software.
Programs Required:
• BMS flashing utility (MonacoUDSClient)
• Proterra Diagnostic Tool
• CAVTAN Parameter Editor v3.03 (dash programming)
3|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Software Files Required / Preparation
It is recommended that you copy the entire “service bulletin files” folder to your local machine in order
to more effectively keep track of the software versions you are deploying:
\\bus.local\files\Engineering\Service Bulletins\Service Bulletin Files for SB-19-97\
•
Body Controller Version 40.28:
o 044740.ZR32A_A
•
Powertrain:
o Main Version 2.4.1 : 042887.hex
o SEPTA Version 2.5.1: 042886.hex
o NYCT Version 2.6.1: 042885.hex
•
CCS Charger Controller:
o Dual Port
▪ Part number 047977.zip
▪ CC_2_0_4.srec
o Single Port
▪ Part Number 047978.zip
▪ CC_2_1_4.srec
•
ESM Controller Version 2.0.0:
o Part Number 043836
o ESM_Catalyst_2_0_0_release_04_11_2019.srec
•
BMS (E2 Pack) Software:
o Part Number 038975
o 0117340DE_MonacoBMS_Main.mbms
o 0117340AE_MonacoSC_Safety.mbms
•
Dash Software - Version 6:
o 031728_rev6.zip
4|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Contents
Description ............................................................................................................................................ 1
Summary of Software Changes ......................................................................................................... 2
Tools/Programs Required.................................................................................................................. 3
Software Files Required .................................................................................................................... 4
Connect to the Vehicle to Start the Proterra Diagnostics Tool .............................................................. 6
Verify and Update the BMS (Battery Pack) Software ............................................................................ 9
Verify Current Software Version ........................................................................................................ 9
Update Using the Proterra Diagnostic Tool ..................................................................................... 10
Update Using MonacoUDS Client (Alternate Method) ..................................................................... 13
Verify and Update ESM Controller Software Version: ......................................................................... 20
Verify Current Software Version ...................................................................................................... 20
Update Using the Proterra Diagnostic Tool ..................................................................................... 21
Update Using Microboot (alternate method) .................................................................................... 23
Verify and Update Charge Controller Software Version ...................................................................... 24
Verify Current Software Version ...................................................................................................... 24
Update Using the Proterra Diagnostic tool ...................................................................................... 25
Update Using Microboot (alternate method) .................................................................................... 27
Verify and Update Powertrain Software Version ................................................................................. 28
Verify Current Software Version ...................................................................................................... 28
Update Powertrain Software ............................................................................................................ 29
Verify and Update Dash Software Version .......................................................................................... 31
Verify Current Software Version ...................................................................................................... 31
Update Dash Software .................................................................................................................... 32
Verify and Update Body Software Version .......................................................................................... 36
Verify Current Software Version ...................................................................................................... 36
Update Body Controller Software .................................................................................................... 40
Store/Import Customer Configuration Dataset................................................................................. 44
Verification of Customer Configuration ............................................................................................ 46
Verify Traction Motor Software Version .............................................................................................. 47
Verify Current Software Version ...................................................................................................... 47
Check List for Software Versions Deployed ........................................................................................ 48
5|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Connect to the Vehicle to Start the Proterra Diagnostics Tool
This process will guide the user to connect to the vehicle with the Proterra Diagnostics Tool.
1. Turn ON the 12/24V rear Vehicle Master Disconnect located behind the vehicle curbside rear
charge port access panel.
2. Turn ON the bus Master Run Switch at the Driver's Workplace and ensure the Dash screen is
ON to display “KEY ON”.
a. This places the vehicle into Key On / Low Voltage state for controller versions to be
checked prior to software flash.
3. For Body Controller Programming:
a. Turn OFF the Master Run Switch at the Driver’s Workplace and ensure the dash screen
is OFF.
b. Turn ON the bus “programming switch” inside the street side wheel well box.
4. Using a T30 Torx screwdriver or appropriate tools, remove the two access covers:
a. Street side wheel well electronics cabinet (ECAB) panel for access to the OBDII Port.
b. Rear deck access panel for OBDII Diagnostic port (NOTE: on E2-35 foot buses this is
located behind the rear barn doors on the left hand side).
5. Power up (boot) the Proterra-supplied laptop containing the Proterra Diagnostic Tool.
6|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
6. Connect the Nexiq USB Link2 device to the laptop and to the appropriate OBDII Diagnostic
Port.
7. For example, here is the Nexiq USB Link connected to the Diagnostic Port located on the
street side wheel well electronics cabinet (eCab):
Diagnostic Port
Nexiq USB Link
8. On the laptop, double-click on the Proterra Diagnostics Tool software icon to
start the software.
9. When the program opens, read and click OK for the prompt.
10. On the Home tab, select the appropriate device from the drop down and click “Connect”.
7|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
11. Once the diagnostic tool has connected to the vehicle, you will have a VIN number and
connection status displayed on the home screen, and tabs available to navigate.
8|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Verify and Update the BMS (Battery Pack) Software
This procedure checks the Body Controller software version and maintains the body controller
parameter configuration data across the flash download of new software.
Verify Current Software Version
1. With the Diagnostic tool connected to the vehicle at the front or rear deck OBDII Port, navigate
to the “Battery Packs” Tab and view the Main and SC SW Versions.
a. If these do not read 117340A and 117340D, as shown below, you must download
battery pack firmware.
b. Be sure you check for each Pack using the drop down in the upper right corner.
Click
Battery Packs
Software
Versions
Pack
Selection
c. NOTE: This pack version will only refresh if you cycle power to the controller (by turning
off the Master Disconnect at the rear of the Vehicle) and also disconnect/reconnect the
Proterra Diagnostic tool.
9|Page
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Update Using the Proterra Diagnostic Tool
1. Ensure the laptop battery is full or it is connected to AC power. The procedure can take up to
ten minutes per pack to complete.
2. Ensure you have the latest software file **.mbms to a known location on the service technician’s
computer (Folder or Desktop).
IMPORTANT! NEVER access the software from the USB memory device, ALWAYS copy the
software files to your computer hard drive and access the software from this location. Secure the bus
with the Vehicle Master Disconnect in the rear ON.
3. Turn the dash Master Switch to ON. Do not press START. Use the hazard lights if necessary
to maintain bus power.
4. With the Proterra diagnostic tool connected to either the front or rear diagnostic port (must
have BCAN data available), navigate to the Configuration tab.
Click
Configuration
Beside Battery
Mgmt System,
Click Start Flash
NOTE: If desired, you can now turn the Master Switch to “OFF”. The battery system remains
active as long as the 12/24V switch is on. This may improve software download speed.
5. Select the option for Battery Management System “Start Flash”.
6. In the pop-up window, select one of the following software configurations to load the
appropriate software into the two controllers for each pack:
a. Pack Safety Controller (SC): 117340A.
b. Main Pack Controller: 117340D.
7. A popup window will appear, “Scanning for available battery management systems”.
10 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
8. Once it is finished scanning, a window with a drop-down list box appears:
9. Select a controller from the drop down list:
a. Safety Controller should display the following per pack, once properly updated:
b. Main controller should display the following per pack, once properly updated:
10. Select a pack controller and click the “Flash” button.
11. The Programming window will come up and may take a few minutes to complete.
11 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
12. When the Programming screen completes, the version numbers will update in the list to show
you have completed that pack (BMS1 Safety has been updated below):
13. After all packs have been updated, cycle power to the bus.
14. Disconnect the diagnostic tool on the home tab and again click Connect.
a. This will refresh the pack version information and allow you to verify all four packs are
properly updated on the “Battery Pack” tab.
Click
Battery Packs
Software
Versions
Pack
Selection
12 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Update Using MonacoUDS Client (Alternate Method)
1. Ensure the laptop battery is full or it is connected to AC power. The procedure can take up to
ten minutes per pack to complete.
2. Download the archive file (.zip or .rar) containing the flashing utility, BMS files, and instructions
to your laptop hard drive.
3. Extract the archive file to a folder at a location of your choosing; remember this location for
future steps.
4. Connect the PCAN dongle to the laptop.
5. Close all CAN utilities running on the laptop: PCAN Explorer, DST, CANalyzer, etc.
Note: These programs can interfere with the tool’s ability to use the PCAN dongle and will
prevent the tool from correctly flashing the BMS.
6. Launch the flashing tool: MonacoUDSClient.exe.
Note: Do not attempt to run the tool straight from the archive file; extract it first, then run it from
the extracted folder.
13 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
7. Click the “Connect” button beside the Connection drop-down menu. If this button is “grayed
out” or not available, you may need to restart your computer to correctly connect to the dongle.
8. The button should change to “Disconnect” once proper communication is established.
NOTE: You will also get a “Connection Successful” message in the status window at the
bottom.
9. Proceed to the next section: Connecting to the bus.
14 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Connecting to the Bus
10. Secure the bus with the Vehicle Master Disconnect in the rear ON.
11. Turn the dash Master Switch to ON. Do not press START. Use the hazard lights if necessary
to maintain bus power.
12. Remove the rear deck access cover behind the back seats using a T30 Torx driver, or square
key if the bus is so equipped.
13. Connect the OBD to DB adapter cable to the rear diagnostic port, then connect the PCAN
dongle to the BCAN port on the cable.
14. Click on the “Scan Dialog” button, then “Start Scan” on the window that pops up.
Note: This will scan for all connected BMS units. On a 4 pack bus you should see 8 instances
of “true” in the first column, as seen below.
15. Once all four packs’ Safety and Main controllers are verified as online, you may proceed with
the flashing procedure.
15 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Flashing the BMS
16. Select the file to flash, under “Select Image.” Click on “Select,” then navigate to the files you
extracted in Step 2 of setup. Select the file labeled “0117340AE_MonacoSC_Safety.mbms”
Note: Each pack will need to be flashed twice, once for the MAIN and once for the SAFETY
controller. The order in which these are done does not matter.
17. Under “Select Device to Flash” use the drop-down menu to select the BMS you are working
on; in the example images, this is BMS01.
16 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
18. Click on the “Enter Bootloader Mode” button. A dialog box will appear to ask for confirmation.
Select “Yes” to confirm and proceed. A second dialog box will appear to notify you the
application reset command was sent, click OK to dismiss it.
19. Click “Flash Device” to load new software into the BMS. A dialog box will appear to ask for
confirmation to proceed, select “Yes” to continue. Another dialog box will appear when flashing
is complete, click OK to continue.
17 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
20. Click “Restart Device” to send a reset command to the BMS. A confirmation box will appear,
click “Yes” to confirm the command.
Note: You will NOT receive a notification box after this, but the Status window will indicate the
restart commands were sent.
21. Repeat step 1-5, this time selecting the file labeled “0117340DE_MonacoBMS_Main.mbms” as
the image to be loaded.
22. Verify the new software load by using the “Scan Dialog” option on the client main screen. You
should see new App Version numbers for the BMS you just flashed, matching the 7-digit
number from the file names selected.
Note: If you do not see these new version numbers, or a pack does not show as present, you
will need to run the flashing procedure again and verify that the controllers reset.
23. Repeat steps 1-6 for the other packs on the bus to update the BMS boards.
18 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Verification and Close-out
24. Run the Scan Dialog once the all the packs have been updated and verify that all packs
installed are Present and the version numbers for all Safety Controllers are the same and
version numbers for all Main Controllers are the same.
25. Close out of the MonacoBMS client, then disconnect the PCAN dongle and adapter cable.
26. Turn the bus Dash Master Switch to OFF, then the Vehicle Master Disconnect to OFF.
Note: Wait 30 seconds.
27. Turn the Vehicle Master Disconnect switch back to ON.
28. Turn the Dash Master Switch ON, then press START.
29. Verify no battery faults are present when the bus reaches RUNNING status.
19 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Verify and Update ESM Controller Software Version:
This procedure checks the ESM Controller software version and upgrades as necessary.
Verify Current Software Version
1. Connect Proterra Diagnostics tool to either front or rear OBDII connector.
2. Navigate to High Voltage Tab.
3. Verify the High Voltage Batteries Controller Software version is “ESMCATALYST_2.0.0”:
4. In this screenshot, the ESM controller software version (middle of the screen) is 2.0.0.
5. If the version is not 2.0.0, proceed to the next section to update the controller software.
20 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Update Using the Proterra Diagnostic Tool
6. Ensure you have the latest software file ESM_**.srec to a known location on the service
technician’s computer (Folder or Desktop).
IMPORTANT! NEVER access the software from the USB memory device, ALWAYS copy the
software files to your computer hard drive and access the software from this location.
7. Turn ON the 12/24V rear Master Disconnect located behind the vehicle curbside rear upper
access panel.
8. Turn OFF the bus High-Voltage Master Switch at the Driver's Workplace and ensure the
Dash screen is OFF.
9. Once connected to the vehicle with the Proterra Diagnostics tool, Click on the “Configuration
Button” to open the Configuration screen and then click the Battery Master Controller “Start
Flash” Button.
Click
Configuration
Beside Battery
Master Controller,
Click Start Flash
21 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
10. The following screen will be displayed. Navigate to the location where you stored the
configuration file earlier. Select the file and click “Open” to load the file.
Select the file and
Click Open
11. The Proterra Diagnostic Tool will attempt to connect to the device.
NOTE: You may receive an error on the first attempt. If so, retry by clicking the Battery
Master Controller “Start Flash” button again.
Error message on
failed first attempt
12. When the software update begins, and the following screens will be displayed.
13. The software update may take several minutes to complete. When the update is complete
the following screen will be displayed. Click the “OK” button to complete the update process.
Click OK
14. The software update is now complete.
15. Reset the bus and proceed.
22 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Update Using Microboot (alternate method)
The purpose of this procedure is to update the ESM Controller software version.
1. Ensure you have the latest program and software file ESM_**.srec to a known location on the
service technician’s computer (Folder or Desktop).
IMPORTANT! NEVER access the software from the USB memory device, ALWAYS copy the
software files to your computer hard drive and access the software from this location.
2. Turn ON the 12/24V rear Master Disconnect located behind the vehicle curbside rear upper
access panel.
3. Turn OFF the bus High-Voltage Master Switch at the Driver's Workplace and ensure the Dash
screen is OFF.
4. Power up (boot) the Proterra-supplied laptop containing the MicroBoot executable file.
5. Connect the octopus cable to the OBD port located in the Rear Deck of the bus.
6. Connect the PCAN dongle to the PCAN connection on the octopus cable.
7. Verify no other CAN utilities are running on the laptop; close PCAN Explorer, Proterra
Diagnostic Tool, etc.
8. Connect PCAN dongle to the USB port on the laptop.
9. Launch MicroBoot on the laptop.
10. Use the “Browse” button to navigate to and select the SREC file to be loaded.
a. The software will load automatically from this point.
11. The software update may take several minutes to complete. When the update is complete the
following screen will be displayed. Click the “OK” button to complete the update process.
12. The ESM Controller software update is now complete.
23 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Verify and Update Charge Controller Software Version
This procedure checks the Charge Controller software version and upgrades as necessary.
Verify Current Software Version
Note: Single Charge Port or Dual Port bus will have different software. The middle integer in the
software version delineates which is which.
-
If single port, your bus should have version (2.1.4).
If dual port, your bus should have version (2.0.4).
1. Connect Proterra Diagnostics tool to either front or rear OBDII connector.
2. Navigate to High Voltage Tab.
3. Verify the Charge Controller Software version is 2.0.4 or 2.1.4.
4. In this screenshot, the charge controller software version (middle right hand side) is 2.1.2.
a. The numbers after the “2.1.2” are a software version hash for engineering tracking.
5. If the version is not 2.0.4 or 2.1.4, proceed to the next section to update the controller software.
24 | P a g e
Headquarters: 1815 Rollins Road, Burlingame, CA 94010
East Coast Manufacturing: 1 Whitlee Court, Greenville, SC 29607
West Coast Manufacturing: 383 Cheryl Lane, City of Industry, CA 91789
Update Using the Proterra Diagnostic tool
6. Ensure you have the latest software file CC**.srec to a known location on the service technician’s
computer (Folder or Desktop).
IMPORTANT! NEVER access the software from the USB memory device, ALWAYS copy the
- Advanced VCI Box, Industry-leading J2534 Pass-Thru...
- High-Speed OEM-Level Diagnostics & Programming: Unlock true...
- Coverage for 17 Car Brands & Ultra Reliability: Works...
- User-Friendly RLink Platform & Expert Support: TOPDON’s...
- 6.6 ft USB-C Cable & Portable Storage Case: The RLink J...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: SC-19-97
Replacement Service Bulletin Number:
MFR Communication Date: 2019-08-14
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS
, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
Last update on 2026-07-02 / Affiliate links / Images from Amazon Product Advertising API
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations
- 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
Last update on 2026-06-30 / Affiliate links / Images from Amazon Product Advertising API
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
Last update on 2026-07-02 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.