Classification:

Reference:

EL19-014

Date:

NTB19-055

July 9, 2019

VOLUNTARY SERVICE CAMPAIGN 2011-2019 LEAF;
LITHIUM-ION BATTERY BONDING PLATES
CAMPAIGN ID #:
APPLIED VEHICLES:

P9312
2011-2017 LEAF (ZE0)
2018-2019 LEAF (ZE1) with 40 kWh battery only

Check Service COMM or Dealer Business Systems (DBS)
National Service History to confirm campaign eligibility.

INTRODUCTION
Nissan is conducting this voluntary service campaign on certain specific model year 20112019 LEAF vehicles to replace the Lithium-Ion battery bonding plates. This service will be
performed at no charge to the customer for parts or labor.
IDENTIFICATION NUMBER
Nissan has assigned identification number P9312 to this campaign. This number must
appear on all communication and documentation of any nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service
department. This includes vehicles purchased from private parties, vehicles presented by
transient (tourists) owners, and vehicles in a dealer’s inventory.

Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/6

SERVICE PROCEDURE
IMPORTANT: Follow all warnings, cautions, and notes in the Electronic Service
Manual (ESM) when working on or near the High Voltage System.


Refer to the ESM for all warnings, cautions, and notes: GENERAL INFORMATION >
GENERAL INFORMATION > PRECAUTION > CAUTIONS AS TO HIGH
VOLTAGE/HIGH VOLTAGE PRECAUTIONS.

NOTE: This procedure is to be performed ONLY by a technician with current LEAF
certification.
1.

Disconnect the high voltage system.


Refer to the ESM for disconnecting the high voltage system: GENERAL
INFORMATION > GENERAL INFORMATION > PRECAUTION > CAUTIONS AS TO
HIGH VOLTAGE > HOW TO DISCONNECT HIGH VOLTAGE > PROCEDURE FOR
DISCONNECTING HIGH VOLTAGE.

2.

Place the vehicle on a lift.

3.

Remove the Li-Ion battery under cover (front).


Refer to the ESM for Li-Ion battery under cover (front) removal: BODY EXTERIOR,
DOORS, ROOF & VEHICLE SECURITY > EXTERIOR > REMOVAL AND
INSTALLATION > LI-ION BATTERY UNDER COVER (FRONT).



See Figure 1 for 2011-2017 models and Figure 2 for 2018-2019 models.

2011-2017

2018-2019
Figure 1

Figure 2

2/6

NTB19-055

4.

Perform potential equalization
inspection.
a. Remove the harness clamp (A) (see
Figure 3).
b. Disconnect the Li-Ion battery high
voltage harness connector (B) (see
Figure 4).

Figure 3

Figure 4

c. Using the insulation resistance tester, check the voltage between both terminals of
the HV harness.
 If the reading is 5 volts or less, continue to step 5.
 If the reading is over 5 volts, wait 10 minutes and retest. Do not continue to step
5 until the reading is 5 volts or less.

3/6

NTB19-055

5.

Locate the two (2) Li-Ion battery
bonding plates connecting the HV
battery case to the vehicle body (see
Figure 5).

6.

Apply rust penetrant to the four (4)
bolts of the bonding plates.


Allow rust penetrant to set for at least
10 minutes.

Figure 5

7.

Remove the four (4) bolts from both
the LH/RH bonding plates (see Figure
6).


8.

Remove the four (4) bolts from both
the LH/RH bonding plates (See
Figure 6).
Remove the bonding plates from the
vehicle.

Figure 6

9.

Install the new bonding plates. See PARTS INFORMATION on page 6.


Install the new bonding plates using new bolts.



Torque the bonding plate bolts to 11 N∙m (1.1kg-m, 8 ft lb).

4/6

NTB19-055

10.

Perform an electric equipotential test
by measuring the resistance between
the two (2) battery pack ground bolts
(A) and the body ground.
 If the resistance is less than 0.1 ohm,
continue to step 11.
 If the resistance is 0.1 ohm or
greater, check and correct the
following:
 Conditions of bonding plate
connection.

11.



Corrosion on bonding plate
mounting surface.



Presence of paint, oil, dirt, or
other substance on the bonding
plate mounting surface.

Figure 7

Reinstall the Li-Ion battery under cover (front).


Refer to the ESM for Li-Ion battery under cover (front) installation: BODY
EXTERIOR, DOORS, ROOF & VEHICLE SECURITY > EXTERIOR > REMOVAL
AND INSTALLATION > LI-ION BATTERY UNDER COVER (FRONT).

12.

Lower the vehicle.

13.

Connect the high voltage system.


Refer to the ESM for connecting the high voltage system: GENERAL
INFORMATION > GENERAL INFORMATION > PRECAUTION > CAUTIONS AS TO
HIGH VOLTAGE > HOW TO DISCONNECT HIGH VOLTAGE > PROCEDURE FOR
CONNECTING HIGH VOLTAGE.

5/6

NTB19-055

PARTS INFORMATION
DESCRIPTION

PART NUMBER

QUANTITY

PLATE-FRAME (Bonding Plate)

744J7-5SB0A

2

SCREWS

01456-00031

4

CLAIMS INFORMATION
Submit a “CM” line claim using the following claims coding:
CAMPAIGN (“CM”) ID
P9312

DESCRIPTION
Replace Bonding Plates

OP CODE
P93120

FRT
1.1

AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
July 9, 2019

NTB19-055

DESCRIPTION
Original bulletin published

6/6

NTB19-055