Classification:

Reference:

EL18-033a

Date:

NTB18-076a

June 28, 2019

2018-2019 KICKS; REAR SONAR DOES NOT WORK WITH
HEADLAMPS AND/OR PARKING LAMPS ON
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.

APPLIED VEHICLES: 2018-2019 Kicks (P15)
APPLIED SYSTEM: Dealer or Vehicle Processing Center (VPC) installed rear sonar ONLY

IF YOU CONFIRM
The rear sonar system does not work with the headlamps and/or parking lamps ON.
NOTE: The rear sonar system works normally with the headlamps and parking lamps OFF.

ACTION
Reposition two (2) of the electrical wire terminals in the driver side rear combination lamp
connector and inside harness connector of the rear sonar harness assembly.

IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/12

SERVICE PROCEDURE
CAUTION: Handle interior trim carefully to avoid damage. Work with clean hands and
clean tools to avoid dirt and stains. Position a clean suitable covering in the vehicle where
work is being performed. Perform repairs in a clean working area on a soft surface, such as
a fender cover, cardboard, etc.
IMPORTANT: Follow all cautions, warnings, and notes in the Electronic Service Manual
(ESM) when working on or near a Supplemental Restraint System (SRS), such as an air
bag.

1.

Turn the ignition ON.

2.

Write down the audio settings.
Presets 1
AM
FM 1
FM 2
SAT 1
SAT 2
SAT 3
Bass
Treble

2

3

Balance

4

Fade

3.

Turn the ignition OFF.

4.

Disconnect the negative battery cable.

5.

Wait at least three (3) minutes before continuing.

2/12

5

6

Speed Sen. Vol.

NTB18-076a

6.

Disconnect the parcel shelf finisher
straps from the back door, and then
remove the parcel shelf finisher.

Finisher

Figure 1
7.

Remove the two (2) driver side
luggage side lower finisher clips with a
suitable plastic trim tool.

Figure 2
8.

Unfasten the two (2) driver side
luggage side upper finisher clips.

Figure 3

3/12

NTB18-076a

9.

Remove the two (2) 10 mm bolts
securing the driver side rear
combination lamp (combination lamp).

10.

Grab the combination lamp, and then
carefully pull it off the vehicle body.


The combination lamp is fastened to
the vehicle body by the 2 bolts and 2
push pins.

Figure 4
NOTE: The push pins are part of the
combination lamp.

Figure 5
11.

Disconnect the combination lamp
harness connector, and then remove
the combination lamp.

Figure 6
4/12

NTB18-076a

NOTE: To keep the orientation of the combination lamp harness connector consistent, hold
it with the lock at the top.
12.

Remove the retainer by inserting a suitable pick in the notched hole and carefully
prying out.

Retainer

Lock

Tool
Figure 7
13.

Remove the terminals of the blue and black wires from the combination lamp
harness connector (see Figure 10 and 11 for selecting the correct blue wire).


Using a suitable pick, pry inward on the locking tabs, and then pull out the wires from
the harness side of the connector. A flashlight may help see the tabs better.

 The right side locking tab in Figure 8 is shown in the unlocked position.
NOTE: The color of the blue wire in Figure 9 is enhanced for easier viewing. Normally,
it is the same shade of blue as the other blue wires.

Retainer
removed
Locking
tab

Locking
tab

Insert
pick here

Figure 8

Figure 9
5/12

NTB18-076a

14.

Insert the black wire where the blue wire was positioned.


15.

A slight audible click is heard when the terminal locks in place. Tug on the wire to
make sure the terminal is locked in.
Insert the blue wire where the black wire was positioned.



A slight audible click is heard when the terminal locks in place. Tug on the wire to
make sure the terminal is locked in.

NOTE: The color of the blue wire in Figure 10 and Figure 11 is enhanced for easier
viewing. Normally, it is the same shade of blue as the other blue wires.

Lock

NG

Blue wire
Black wire

Black wire

Blue wire

Figure 10

16.

OK

Figure 11

Install the retainer with a suitable pair
of needle nose pliers or equivalent
tool.

Figure 12

6/12

NTB18-076a

17.

Locate the foam wrapped harness
connector shown in Figure 13.


This connector will be rewrapped and
fastened in the same position during
assembly. Remember its position.
Area in front of
combination lamp

Luggage
side lower
finisher

18.

Figure 13

Using a suitable cutting tool, cut the
“wire tie”, and then peel off the foam
from the connector.
NOTE: Figure 14 shows the connector
with foam and “wire tie” removed.

Connector

Figure 14

7/12

NTB18-076a

19.

Disconnect the connector.

NOTE:


Perform repairs to the circled
connector, not the one with the red
“X” (see Figure 15).

Figure 15



To keep the orientation of the
connector consistent, hold it with
the lock opening at the bottom.

Lock
opening
Figure 16

8/12

NTB18-076a

20.

Remove the retainer by inserting a suitable pick in the notched hole and carefully
prying out.
Notched
hole

Retainer

Figure 17

21.

Figure 18

Remove both terminals of the blue and black wires from the connector (see Figure
21 and 22 for selecting the correct blue wire).
 Using a suitable pick, pry inward on the locking tabs, and then pull out the wires from
the harness side of the connector. A flashlight may help you see the tabs better.
 The right side locking tab in Figure 19 is shown in the unlocked position.

Retainer
removed
Insert
pick here

Locking
tab

Locking
tab

Figure 19

Figure 20

9/12

NTB18-076a

22.

Insert the black wire where the blue wire was positioned.


23.

A slight audible click is heard when the terminal locks in place. Tug on the wire to
make sure the terminal is locked in.
Insert the blue wire where the black wire was positioned.



A slight audible click is heard when the terminal locks in place. Tug on the wire to
make sure the terminal is locked in.

NG

Blue wire

Black wire

OK

Blue wire

Black wire

Lock
opening
Figure 21

24.

Figure 22

Insert the retainer using a suitable pair
of needle nose pliers.
CAUTION: Make sure none of the
pins are bent.

Figure 23

10/12

NTB18-076a

25.

Reconnect the connector inside the vehicle, and the combination lamp harness
connector.


Make sure an audible click is heard when connecting both connectors.



Install the combination lamp with the 2 push pins only at this time.
CAUTION: Do not let the combination lamp hang by its connector.

26.

Reconnect the negative battery cable.

27.

IMPORTANT: Operate the rear sonar system, verify it works properly with the
headlamps ON and OFF.

28.

Reassemble the vehicle in reverse order of steps 6-11.


Make sure to rewrap the connector inside the vehicle with foam and fasten it
in the same location.



Refer to PARTS INFORMATION for foam and a “wire tie”.



Combination lamp bolts torque: 4.4 N•m (0.54 kg-m, 39 in lbs)

29.

Reset/reinitialize systems as needed.


Refer to the Electronic Service Manual (ESM) for a list of systems needing
reset/reinitialization.
 ELECTRICAL POWER & CONTROL > POWER SUPPLY, GROUND & CIRCUIT
ELEMENTS > BASIC INSPECTION > INSPECTION AND ADJUSTMENT –
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL



The list of systems often includes items such as the power window control system,
automatic air conditioning, engine fuel management (Idle Air Volume Learn), etc.

11/12

NTB18-076a

PARTS INFORMATION
DESCRIPTION

PART NUMBER

QUANTITY

EPDM SEMI CLOSED CELL 5 mm

J-50397-1

As needed (a) (b) (c)

“Wire Tie”

--

(b)

(a)
(b)
(c)

EPDM Semi Closed Cell 5 mm adhesive foam is available in the dealer Squeak &
Rattle Kit J-50397. Additional supplies may be ordered from Tech•Mate (1-800-6622001).
Shop supply.
EPDM Semi Closed Cell 5 mm adhesive foam is recommended, but an equivalent
product may be used.

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Repair RR Sonar Harness
T99Q1-5RL0A
RX6VAA
ZE
32
0.6

AMENDMENT HISTORY
PUBLISHED DATE REFERENCE

DESCRIPTION

November 6, 2018

NTB18-076

Original bulletin published.

June 28, 2019

NTB18-076a

APPLIED VEHICLES section and Title revised.

12/12

NTB18-076a