NHTSA ID Number: 10161881
Manufacturer Communication Number: 18NA355
TSB/Document Date: 2019-07-01
Summary
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
published. The exchange process is required to obtain
proper level of new blue label Mobil 1
Synthetic LV ATF
HP fluid. Intermixing of other types of transmission fluid
or aftermarket additive packages will result in a low
concentration level of new fluid and will not provide
satisfactory results.
1. Fill the DT-45096 with 20 quarts of HP fluid.
Bulletin No.: 18-NA-355
May, 2019
Page 11
4194576
Note: The MAF sensor must stay connected so that no
DTCs will set.
2. Separate the engine upper air filter box (1) from the
lower air filter housing to gain access to the upper
transmission oil cooler line.
5181322
5181307
Note: Upper air filter box removed for clarity.
3. Remove the cooler line from the transmission oil
cooler.
4. Install end of the DT-52263-5 Radiator Cooler
Drain Adapter (1) to the DT-52263-1 Block
Assembly.
5. Install the DT-52263-5 Radiator Cooler Drain
Adapter into the upper transmission oil cooler line
port of the transmission oil cooler.
6. Install the DT-45096-31 adapter (3) over the
removed transmission oil cooler line (2) to prevent
any fluid spillage.
Page 12
May, 2019
Bulletin No.: 18-NA-355
7. Place the hose in the GE-47716-2 Graduated
Measuring Bucket, utilizing a Spring Clamp to
retain the hose.
8. Raise the vehicle.
5182541
9. Install the DT-45096-31 adapter (1) to the
DT-51190 fluid fill adapter (2).
3723839
Important: DO NOT overtighten the DT-51190 as it
can be damaged by excessive torque. Do not
exceed 9 Y (80 lb in).
11. Install the DT-51190/DT-45096-31 assembly and
hand tighten.
12. Connect the TransFlow fluid feed (supply) line (3)
to the DT-45096-31 adapter (2).
13. Lower the vehicle.
Caution: DO NOT REMOVE MORE THAN 3 QTS OF
FLUID AS IT COULD CAUSE FLUID PUMP
CAVITATION AND POSSIBLY DAMAGE THE
TRANSMISSION.
14. Utilizing the graduated bucket, start the engine and
run 30-45 seconds until 3 quarts of fluid is
expelled.
15. Shut the engine off immediately.
16. Connect the DT-45096 to the vehicle battery
12 volts and connect shop air to the air connection.
3723844
10. Remove the level set plug (1) from the
transmission oil pan.
5181027
Bulletin No.: 18-NA-355
May, 2019
Page 13
Important: ADDING TOO MUCH FLUID TO THE
TRANSMISSION MAY CAUSE FLUID TO BE
EXPELLED FROM THE VENT SYSTEM. DO NOT
OVERFILL THE TRANSMISSION.
17. Switch the DT-45096 TransFlow to Flow and add
4 quarts of HP to the transmission.
5181020
18. Set the TransFlow switch to idle (Reducing fluid
level in the TransFlow from 20–16).
19. Switch the TransFlow DT-45096 to Flow and start
the engine:
19.1. Add a maximum of 4 quarts of HP Fluid to
the transmission, turn the TransFlow switch
to idle once 4 quarts have been added, while
allowing 4 additional quarts of oil to fill the
DT-graduated cylinder (Reducing fluid level
in the TransFlow from 16–12).
Note: DO NOT add additional transmission fluid until
the 4 quarts of oil have been removed from the
transmission (Reducing fluid level in the TransFlow
from 12–8).
19.2. Repeat step 19.1.
19.3. Add a maximum of 5 quarts of HP Fluid to
the transmission while allowing 5 additional
quarts of oil to fill the DT-graduated bucket
(Reducing fluid level in the TransFlow from
8–3).
5181401
20.
21.
22.
23.
24.
25.
26.
19.4. Shut the engine off once 16 quarts of oil
have been collected.
19.5. Properly dispose of the collected
transmission fluid.
Remove the DT-52263-5 Radiator Cooler Drain
Adapter and DT-52263-1 Block Adapter from the
transmission oil cooler.
Remove the DT-45096-31 from the transmission oil
cooler line and install the transmission oil cooler
line using a new retaining clip.
Install the engine upper air filter box back into
position.
Partially raise the vehicle.
Start the engine.
Using care, shift the transmission through all
forward ranges and Reverse.
Shift the transmission into Park.
Page 14
May, 2019
27. Perform the Transmission Fluid Level and
Condition Check outlined below in this procedure:
27.1. Get the transmission fluid temperature to the
proper temperature.
27.2. Raise the vehicle and remove the DT-51190/
DT-45096-31 assembly.
27.3. Install the level set plug.
Tighten
Tighten the plug to 9 Y (80 lb in).
The TCC shudder condition should be directional
improved immediately after the fluid exchange
procedure. It may take up to 320 km (200 mi) for the
TCC shudder condition to be eliminated. It is not a
requirement for the dealer to drive the vehicle 320 km
(200 mi). The customer should be advised that the full
effect will take up to 320 km (200 mi) and a minimum of
two cold to operating temperature drive cycles.
Bulletin No.: 18-NA-355
Fluid Exchange Procedure – Camaro V8 Not
Equipped with a Rear Differential Cooler
Important: This procedure must be followed as
published. The exchange process is required to obtain
proper level of new blue label Mobil 1 Synthetic LV ATF
HP fluid. Intermixing of other types of transmission fluid
or aftermarket additive packages will result in a low
concentration level of new fluid and will not provide
satisfactory results.
1. Fill the DT-45096 with 20 quarts of HP fluid.
Bulletin No.: 18-NA-355
May, 2019
Page 15
4194576
Note: The MAF sensor must stay connected so that no
DTCs will set.
2. Separate the engine upper air filter box (1) from the
lower air filter housing to gain access to the upper
transmission oil cooler line.
4. Install the DT-52263-2 Cooler Line Plug into the
radiator cooler.
5. Install the DT-52263-4 Hose onto DT-52263-1
Block Assembly install the DT-52263-4 onto the
removed transmission oil cooler line.
6. Place the hose of the DT-52263-1 in the
GE-47716-2 Graduated Measuring Bucket,
utilizing a Spring Clamp to retain the hose.
7. Raise the vehicle.
5182541
5181307
Note: Upper air filter box removed for clarity.
3. Remove the upper cooler line from the
transmission oil cooler.
8. Install the DT-45096-31 adapter (1) to the
DT-51190 fluid fill adapter (2).
Page 16
May, 2019
Bulletin No.: 18-NA-355
14. Shut the engine off immediately.
15. Connect the DT-45096 to the vehicle battery
12 volts and connect shop air to the air connection.
3723844
9. Remove the level set plug (1) from the
transmission oil pan.
5181027
Important: ADDING TOO MUCH FLUID TO THE
TRANSMISSION MAY CAUSE FLUID TO BE
EXPELLED FROM THE VENT SYSTEM. DO NOT
OVERFILL THE TRANSMISSION.
16. Switch the DT-45096 TransFlow to Flow and add
4 quarts of HP to the transmission.
3723839
Important: DO NOT overtighten the DT-51190 as it
can be damaged by excessive torque. Do not
exceed 9 Y (80 lb in).
10. Install the DT-51190/DT-45096-31 assembly and
hand tighten.
11. Connect the TransFlow fluid feed (supply) line (3)
to the DT-45096-31 adapter (2).
12. Lower the vehicle.
Caution: DO NOT REMOVE MORE THAN 3 QTS OF
FLUID AS IT COULD CAUSE FLUID PUMP
CAVITATION AND POSSIBLY DAMAGE THE
TRANSMISSION.
13. Utilizing the graduated bucket, start the engine and
run 30-45 seconds until 3 quarts of fluid is
expelled.
5181020
17. Set the TransFlow switch to idle (Reducing fluid
level in the TransFlow from 20–16).
Bulletin No.: 18-NA-355
May, 2019
18. Switch the TransFlow DT-45096 to Flow and start
the engine:
18.1. Add a maximum of 4 quarts of HP Fluid to
the transmission, turn the TransFlow switch
to idle once 4 quarts have been added, while
allowing 4 additional quarts of oil to fill the
DT-graduated cylinder (Reducing fluid level
in the TransFlow from 16–12).
Note: DO NOT add additional transmission fluid until
the 4 quarts of oil have been removed from the
transmission (Reducing fluid level in the TransFlow
from 12–8).
18.2. Repeat step 18.1.
18.3. Add a maximum of 5 quarts of HP Fluid to
the transmission while allowing 5 additional
quarts of oil to fill the DT-graduated bucket
(Reducing fluid level in the TransFlow from
8–3).
Page 17
21. Install the engine upper air filter box back into
position.
22. Partially raise the vehicle.
23. Start the engine.
24. Using care, shift the transmission through all
forward ranges and Reverse.
25. Shift the transmission into Park.
26. Perform the Transmission Fluid Level and
Condition Check outlined below in this procedure:
26.1. Get the transmission fluid temperature to the
proper temperature.
26.2. Raise the vehicle and remove the DT-51190/
DT-45096-31 assembly.
26.3. Install the level set plug.
Tighten
Tighten the plug to 9 Y (80 lb in).
The TCC shudder condition should be directional
improved immediately after the fluid exchange
procedure. It may take up to 320 km (200 mi) for the
TCC shudder condition to be eliminated. It is not a
requirement for the dealer to drive the vehicle 320 km
(200 mi). The customer should be advised that the full
effect will take up to 320 km (200 mi) and a minimum of
two cold to operating temperature drive cycles.
Fluid Exchange Procedure - Camaro, CTS and
ATS Equipped with a Rear Differential Cooler
Important: This procedure must be followed as
published. The exchange process is required to obtain
proper level of new blue label Mobil 1 Synthetic LV ATF
HP fluid. Intermixing of other types of transmission fluid
or aftermarket additive packages will result in a low
concentration level of new fluid and will not provide
satisfactory results.
1. Fill the DT-45096 with 20 quarts of HP fluid.
2. Raise the vehicle on a hoist.
5181401
18.4. Shut the engine off once 16 quarts of oil
have been collected.
18.5. Properly dispose of the collected
transmission fluid.
19. Remove the DT-52263-4 and DT-52263-1 Block
Adapter from the transmission oil cooler line.
20. Remove the DT-52263-2 Cooler Line Plug from the
transmission oil cooler at the radiator and install
the transmission oil cooler line using a new
retaining clip.
Page 18
May, 2019
Bulletin No.: 18-NA-355
3723844
9. Remove the level set plug (1) from the
transmission oil pan.
5182245
3. Remove the lower/front transmission oil cooler line
(2) at the rear differential.
4. Install the DT-52263-2 Cooler Line Plug (1) into the
rear differential to prevent fluid loss.
5. Install one end of the DT-52263-4 hose (4) to the
open port of the DT-52263-1 Block Assembly (3).
6. Install the other end of the DT-52263-4 hose to the
transmission oil cooler line.
7. Place the hose in the GE-47716-2 Graduated
Measuring Bucket, utilizing a Spring Clamp to
retain the hose.
3723839
5182541
8. Install the DT-45096-31 adapter (1) to the
DT-51190 fluid fill adapter (2).
Important: DO NOT over tighten the DT-51190 as it
can be damaged by excessive torque. Do not
exceed 9 Y (80 lb in).
10. Install the DT-51190/DT-45096-31 assembly and
hand tighten.
11. Connect the TransFlow fluid feed (supply) line (3)
to the DT-45096-31 adapter (2).
12. Lower the vehicle.
Caution: DO NOT REMOVE MORE THAN 3 QTS OF
FLUID AS IT COULD CAUSE FLUID PUMP
CAVITATION AND POSSIBLY DAMAGE THE
TRANSMISSION.
13. Utilizing the graduated bucket, start the engine and
run 30-45 seconds until 3 quarts of fluid is
expelled.
Bulletin No.: 18-NA-355
May, 2019
Page 19
14. Shut the engine off immediately.
15. Connect the DT-45096 to the vehicle battery
12 volts and connect shop air to the air connection.
5181027
16. Switch the TransFlow DT-45096 to Flow and add
4 quarts of HP to the transmission.
17. Set the TransFlow switch to idle (Reducing fluid
level in the TransFlow from 20–16).
18. Switch the TransFlow DT-45096 to Flow and start
the engine:
18.1. Add a maximum of 4 quarts of HP Fluid to
the transmission, turn the TransFlow switch
to idle once 4 quarts have been added, while
allowing 4 additional quarts of oil to fill the
DT-graduated bucket (Reducing fluid level in
the TransFlow from 16–12).
Note: DO NOT add additional transmission fluid until
the 4 quarts of oil have been removed from the
transmission (Reducing fluid level in the TransFlow
from 12–8).
18.2. Repeat step 18.1.
18.3. Add a maximum of 5 quarts of HP Fluid to
the transmission while allowing 5 additional
quarts of oil to fill the DT-graduated bucket
(Reducing fluid level in the TransFlow from
8–3).
5181401
19.
20.
21.
22.
23.
24.
18.4. Shut the engine off once 16 quarts of fluid
have been collected.
18.5. Properly dispose of the collected
transmission fluid.
Raise the vehicle.
Remove the DT-52263-2 Cooler Line Plug from
rear differential and install the transmission oil
cooler line using a new retainer clip.
Remove the DT-52263-4 from the transmission oil
cooler line.
Install the transmission oil cooler line using a new
retainer clip.
Partially lower the vehicle.
Using care, shift the transmission through all
forward ranges and Reverse.
24.1. Get the transmission fluid temperature to the
proper temperature.
24.2. Raise the vehicle and remove the DT-51190/
DT-45096-31 assembly.
24.3. Install the level set plug.
Tighten
Tighten the plug to 9 Y (80 lb in).
Page 20
May, 2019
Bulletin No.: 18-NA-355
The TCC shudder condition should be directional
improved immediately after the fluid exchange
procedure. It may take up to 320 km (200 mi) for the
TCC shudder condition to be eliminated. It is not a
requirement for the dealer to drive the vehicle 320 km
(200 mi). The customer should be advised that the full
effect will take up to 320 km (200 mi) and a minimum of
two cold to operating temperature drive cycles.
Fluid Exchange Procedure - Corvette and CT6
Important: The Drain and Fill Procedure Will Need
to be Performed Three Times.
Important: This procedure must be followed as
published. The exchange process is required to obtain
proper level of new blue label Mobil 1 Synthetic LV ATF
HP fluid. Intermixing of other types of transmission fluid
or aftermarket additive packages will result in a low
concentration level of new fluid and will not provide
satisfactory results.
1. Fill the DT-45096 with 24 quarts of HP fluid.
2. Raise the vehicle.
3. Using care, remove the transmission oil pan and
drain the transmission fluid.
4. Install the transmission oil pan.
3723844
6. Remove the level set plug (1) from the
transmission oil pan.
5182541
5. Install the DT-45096-31 adapter (1) to the
DT-51190 fluid fill adapter (2).
3723839
Important: DO NOT over tighten the DT-51190 as it
can be damaged by excessive torque. Do not
exceed 9 Y (80 lb in).
7. Install the DT-51190/DT-45096-31 assembly and
hand tighten.
8. Connect the TransFlow fluid feed (supply) line (3)
to the DT-45096-31 adapter (2).
9. Connect the DT-45096 TransFlow to the vehicle
battery 12 volts and connect shop air to the air
connection.
10. Switch the DT-45096 TransFlow to Flow and fill the
transmission with 8 quarts of transmission fluid.
10.1. Switch the DT-45096 TransFlow to idle.
11. Partially lower the vehicle and run the transmission
through all 8 forward gears, Reverse and Neutral.
Bulletin No.: 18-NA-355
May, 2019
12. Repeat steps 2-4 and 9-10 for 2nd drain and fill.
13. Repeat step 2-3, clean the transmission oil pan
and magnet, repeat step 4 and step 10-11.
14. Perform the Transmission Fluid Level and
Condition Check outlined below in this procedure:
14.1. Get the transmission fluid temperature to the
proper temperature.
14.2. Raise the vehicle and remove the DT-51190/
DT-45096-31 assembly.
14.3. Install the level set plug.
Tighten
Tighten the plug to 9 Y (80 lb in).
The TCC shudder condition should be directional
improved immediately after the fluid exchange
procedure. It may take up to 320 km (200 mi) for the
TCC shudder condition to be eliminated. It is not a
requirement for the dealer to drive the vehicle 320 km
(200 mi). The customer should be advised that the full
effect will take up to 320 km (200 mi) and a minimum of
two cold to operating temperature drive cycles.
Transmission Fluid Level and Condition
Check
This procedure checks both the transmission fluid level,
as well as the condition of the fluid itself. Because the
transmission on this vehicle is not equipped with a fill
tube and dipstick, a tube in the bottom pan is used to
set the fluid level.
Warning: The transmission fluid level must be
checked when the transmission fluid temperature
(TFT) is between 35–45°C (95–113°F). If the TFT is
not within this range, either idle or brake torque the
vehicle to raise the fluid temperature, or shut off the
vehicle to allow the fluid to cool as required. Setting
the fluid level with a TFT outside this range will
result in either an under or over-filled transmission.
TFT>45°C=under-filled, TFT
- 6X better wear protection on critical engine parts than...
- 1.3X better sludge protection than industry standards*
- 3X Stronger against viscosity breakdown than leading full...
- Protection for 10,000 miles between oil changes
- Meets or exceeds the following specifications: API SP/SN...
- Formulated for engines with 75,000 miles or more, Valvoline...
- Delivers 20% better wear protection and 15% better sludge...
- Extra detergents safeguard against friction, corrosion and...
- Advanced friction-fighting additives help maximize...
- Provides performance benefits for high mileage, new and...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 18NA355
Replacement Service Bulletin Number:
MFR Communication Date: 2019-05-21
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: POWER TRAIN
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS
, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
Last update on 2026-07-02 / Affiliate links / Images from Amazon Product Advertising API
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations
- 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
Last update on 2026-06-30 / Affiliate links / Images from Amazon Product Advertising API
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
Last update on 2026-07-02 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.