NHTSA ID Number: 10161827
Manufacturer Communication Number: WUF-91R
TSB/Document Date: 2019-07-01
Summary
Subaru
of America, Inc. (Subaru) is recalling certain vehicles in the ranges listed below to inspect and potentially replace the ignition switch. A total of 511 U.S. vehicles will be affected by this recall.
ATTENTION:
CLAIMS PERSONNEL q
IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
SERVICE MANAGER
© 2019 Subaru of America, Inc. All rights reserved.
GENERAL MANAGER q
PARTS MANAGER
q
q
PRODUCT CAMPAIGN BULLETIN
APPLICABILITY:
SUBJECT:
NUMBER: WUF-91R
2009-2013 Forester
2008-2014 Impreza
2005-2014 Legacy
2005-2014 Outback
2006-2008 Tribeca
NHTSA: 19V-297
DATE: 04/15/19
REVISED: 05/22/19
Replacement Ignition Switch Recall
INTRODUCTION:
Subaru of America, Inc. (Subaru) is recalling certain vehicles in the ranges listed below to inspect and
potentially replace the ignition switch. A total of 511 U.S. vehicles will be affected by this recall.
AFFECTED VEHICLES:
Coverage for this recall must be confirmed by using the
Vehicle Coverage Inquiry function on Subarunet.com.
This information is now available.
Model Years
Carline
Vehicle Count
2009-2013
Forester
266
2009-2011
Impreza
58
2008-2014
WRX
22
2005-2014
Legacy
47
2005-2014
Outback
108
2006-2008
Tribeca
10
DESCRIPTION OF THE DEFECT AND SAFETY RISK:
In some of the potentially affected vehicles, a previously-installed Genuine Subaru replacement
ignition switch may contain a ball spring susceptible to long-term wear and possible fatigue breakage.
If the ball spring inside the ignition switch breaks, the retention force of the ignition switch would be
reduced. If this occurs and heavier items are attached to the ignition key while the vehicle is driven
over rough surfaces, the weight may exceed the retention force of the broken ball spring and pull the
ignition switch from the “ON” position to the “ACC” position.
If the ignition switch is pulled from the “ON” position to the “ACC” position the engine would stop
running while the vehicle is in motion, increasing the risk of a crash. If a crash occurs under this
condition, the airbag system may not react as designed, increasing the risk of injury.
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.
Continued...
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 1 of 10
DESCRIPTION OF THE REMEDY:
Subaru dealers will inspect the lot number of the ignition switch and if it is within the affected range,
replace it with a remedied one.
RETAILER RESPONSIBILITY:
Any vehicles listed in any recall/campaign that are in retailer stock must be:
•
Immediately identified.
•
Tagged or otherwise marked to prevent their delivery or use prior to repair.
•
Repaired in accordance with the repair procedures outlined in the Product Campaign
Bulletin.
Retailers are to promptly perform the applicable service procedures to correct all potentially affected
vehicles in their inventory (used, demo & SSLP). Additionally, whenever a vehicle subject to this
recall is taken into retailer inventory necessary steps should be taken to ensure the recall correction
has been made before selling or releasing the vehicle.
The vehicles included in this recall were identified based on retail sales records of specific Genuine
Subaru replacement ignition switches sold between February 2017 and October 2018, containing
specific manufacturing lot numbers. A very small quantity of the sales could not be traced to a
specific VIN. As a result, the estimated number of unidentified potentially defective Genuine Subaru
replacement ignition switches is less than 10.
If a customer who owns a similar vehicle not identified under this recall either (1) has knowledge
that they had a Genuine Subaru replacement ignition switch installed in their vehicle after February
21, 2017, or (2) purchased the vehicle as used after February 21, 2017 and is unaware of the service
history of the vehicle, they may qualify to have the ignition switch lot number checked upon request.
To qualify, the vehicle must have a mechanical key ignition and be included in the following: 20052014MY Legacy/Outback, 2006-2014MY Tribeca, 2008-2011MY Impreza, 2008-2014MY Impreza
WRX/WRX, or 2009-2013MY Forester applicable to one of the two situations stated above. If a
customer makes such a request, fully document the situation and contact the Subaru Claims Helpline
at 1-866-782-2782 for further instruction.
RETAILER AFFECTED VIN LISTS:
Each Subaru retailer will receive an affected VIN list from their Zone Office. Vehicles will be
assigned to retailers as follows:
•
Original vehicle owners are assigned to the original selling retailer when their current address
is within a 100-mile radius of that retailer.
•
If the original selling retailer is inactive, the VIN has been assigned to the nearest active
retailer.
•
For any new owners or when original owners live more than 100 miles from the original
selling retailer, the VIN has been assigned to the nearest active retailer.
Continued...
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 2 of 10
IMPORTANT: Retailer affected VIN lists include information for vehicles affected by this recall.
This information will enable retailers to follow up with owners of affected vehicles. The lists contain
owners’ names and phone numbers obtained from State Motor Vehicle Registration Records. The
use of such motor vehicle registration data for any other purpose is unlawful. Accordingly, retailers
are required to limit the use of these lists for the sole purpose of completing this recall.
OWNER NOTIFICATION:
Subaru is in the process of acquiring current registration data and will notify affected vehicle owners
by first class mail in May. Owners with a valid email address on file will also be notified by email.
Retailers will be advised when the notification is scheduled.
PART INFORMATION:
2005-2006MY Legacy / Outback
and Tribeca: P.N. 83131AG000
2007-2014MY Legacy / Outback, Forester
Impreza / WRX / STI P.N. 83131KG000
REMINDER: Always order the most up-to-date replacement parts based on the specific VIN being
repaired.
SERVICE PROCEDURE / INFORMATION:
This procedure involves inspection of the lot number located on the face of the ignition switch. On
some of the affected vehicles, a mechanical key ignition switch installed as a service spare part may
contain a ball spring which could be susceptible to long-term wear and possible fatigue breakage.
If the ball spring breaks, the retention force of the ignition switch is reduced. If heavier items are
attached to the ignition key and the vehicle is driven over rough surfaces, the weight of the items
may exceed the retention force of the broken ball spring and pull the ignition switch from the “ON”
position to the “ACC” position. If this occurs the engine may unexpectedly stop running.
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
The service procedures for Ignition Switch replacement remain unchanged. Always refer to the
applicable Service Manual and review the full requirements of the repair being performed. The
Service Manual procedures contain information critical to performing an effective repair the first
time and every time. This includes but is not limited to: important SAFETY precautions, proper
inspection criteria, necessary special tools, required processes and related one-time-use parts needed
for a complete and lasting repair.
Continued...
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 3 of 10
Step 1- Record the customer’s radio station presets and Navigation Favorites (where applicable).
Step 2- Disconnect the Battery ground cable and wait at least 60 seconds before proceeding.
Step 3- CAREFULLY remove the instrument panel lower cover and steering column upper and
lower covers following the procedures in the applicable Service Manual.
REMINDER: Always take all proper precautions to protect these highly visible trim components
from damage during their removal and reinstallation.
Step 4- CAREFULLY access and remove the electrical portion of the ignition switch assembly to
confirm the Lot Number. (NOTE: To complete this inspection, follow the steps below specific to
each MY / Model.)
•
For 2005-2007MY Legacy / Outback and Tribeca Models:
1. Disconnect the ignition switch harness and key lock solenoid connectors.
CAUTION: The harness for the key lock solenoid is routed around the ignition lock assembly. After
CAREFULLY disconnecting the harness connector, do not pull on, reposition or un-twist the key
lock solenoid harness any more than necessary to facilitate removing the ignition switch from ignition
lock assembly.
2. Remove the two (2) ignition switch Philips head retaining screws.
3. Remove the ignition switch from the ignition lock assembly.
Continued...
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 4 of 10
4. Confirm the Lot Number on the face of the ignition switch using the chart below.
Using the chart above as a guide, if the Lot Number is between 6Z18 (December 18, 2016) and 7602
(June 2, 2017), the ignition switch MUST be replaced. If the Lot Number is illegible, REPLACE the
ignition switch assembly.
NOTE: Always record the ORIGINAL ignition switch Lot Number on the hard copy of the Repair
Order as it will be required for claim submission.
IMPORTANT CAUTIONS:
•
If replacing the ignition switch on one of these models, CAREFULLY removing the key
lock solenoid connector from the ignition switch by using pliers as shown below and swap it
over to the new switch. Apply electrical tape to the plier jaws to protect the connector.
•
If the connector or wiring is damaged, the ignition steering lock assembly will require
replacement including recoding of the new assembly to match the original keys by a certified
locksmith.
•
NOTE: Removing the key lock solenoid connector, as shown in the sequence below, is only
required if the ignition switch requires replacement.
5. CAUTION: After reinstalling the ignition switch back into the lock housing, torque the 2
retaining screws to 1.1 Nm (9.7 inch-pounds). DO NOT OVER-TIGHTEN. Confirm
all functions of the ignition switch (OFF, ACC, ON, and START). With the engine
OFF and parking brake fully engaged, confirm the function of the ignition interlock by
attempting key removal in a gear other than park. Proceed to Step 5 below.
•
For 2008-2009MY Legacy, Outback, & 2008-2014MY Impreza, WRX, STI and Forester
Models:
1. Remove the harness connector from the ignition switch.
2. Remove the two (2) ignition switch Philips head retaining screws.
Continued...
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 5 of 10
3. Remove the ignition switch from the ignition lock assembly.
4. Confirm the Lot Number on the face of the ignition switch using the chart below.
Using the chart above as a guide, if the Lot Number is between 6Z18 (December 18, 2016) and
7602 (June 2, 2017), the ignition switch MUST be replaced. NOTE: If the Lot Number is illegible,
REPLACE the ignition switch assembly.
5. CAUTION: After reinstalling the ignition switch back into the lock housing, torque the 2
retaining screws to 1.1 Nm (9.7 inch-pounds). DO NOT OVER-TIGHTEN. Confirm
all functions of the ignition switch (OFF, ACC, ON, and START). With the engine
OFF and parking brake fully engaged, confirm the function of the ignition interlock by
attempting key removal in a gear other than park. Proceed to Step 5 below.
•
For 2010-2014MY Legacy / Outback Models:
For these models, the ignition switch is accessed from the right side of the steering column.
1. Remove the harness connector from the ignition switch.
2. Remove the two (2) Philips head retaining screws.
3. Remove the ignition switch from the ignition lock assembly.
Continued...
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 6 of 10
4. Confirm the Lot Number on the face of the ignition switch using the chart below.
NOTE: If the Lot Number is illegible, REPLACE the ignition switch assembly.
Using the chart above as a guide, if the Lot Number is between 6Z18 (December 18, 2016) and
7602 (June 2, 2017), the ignition switch MUST be replaced. NOTE: If the Lot Number is illegible,
REPLACE the ignition switch assembly.
5. CAUTION: After reinstalling the ignition switch back into the lock housing, torque the 2
retaining screws to 1.1 Nm (9.7 inch-pounds). DO NOT OVER-TIGHTEN. Confirm
all functions of the ignition switch (OFF, ACC, ON, and START). With the engine
OFF and parking brake fully engaged, confirm the function of the ignition interlock by
attempting key removal in a gear other than park. Proceed to Step 5 below.
Step 5- CAREFULLY reinstall the column covers and instrument panel lower cover in reverse order
of removal. IMPORTANT: Always be CAREFUL to engage the alignment pins and retaining
claws properly as shown below.
Step 6- Reset the customer’s radio station presets and Navigation Favorites (where applicable) to
complete the procedure.
CLAIM REIMBURSEMENT AND ENTRY PROCEDURES:
Credit to perform this recall will be based on properly completed repair order information. Retailers
may submit claims through Subarunet.com.
Labor Description
Labor Operation #
IGNITION SW. R&R, LOT NO.
INSPECTION ONLY
186-310
IGNITION SW. R&R, LOT NO.
INSPECTION & REPLACEMENT
186-311
Fail Code
Labor Time
Claim Type
0.6
WUF-91
RC
0.6
REMINDER: The Lot Number for the ORIGINAL ignition switch must be entered in the
Miscellaneous Detail field.
Continued...
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 7 of 10
IMPORTANT REMINDERS:
•
SOA strongly discourages the printing and/or local storage of service information as
previously released information and electronic publications may be updated at any time.
•
Always check for any open recalls or campaigns anytime a vehicle is in for servicing.
•
Always refer to STIS for the latest service information before performing any repairs.
Continued...
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 8 of 10
OWNER NOTIFICATION LETTER
URGENT
IMPORTANT SAFETY RECALL
This notice applies to the VIN below
Subaru of America, Inc
PO Box 9103
Camden, NJ 08101-9877
844-373-6614
www.subaru.com
Subaru Safety Recall WUF-91
NHTSA Recall ID 19V-297
May 2019
Dear Subaru Owner:
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
SUBARU OF AMERICA, INC. has decided that a defect, which relates to motor vehicle safety, exists in certain
2009-2013 model year Forester vehicles, 2008-2011 model year Impreza vehicles, 2008-2014 model year WRX
vehicles, 2005-2014 model year Legacy vehicles, 2005-2014 model year Outback vehicles, and 2006-2008 model
year Tribeca vehicles.
You received this notice because our records indicate that you currently own one of these vehicles.
REASON FOR THIS SAFETY RECALL
On certain vehicles included in this safety recall, the ignition switch was previously replaced with one that may
contain a defective ball spring susceptible to long-term wear and possible fatigue breakage. If that ball spring
breaks, the retention force of the ignition switch would be reduced. If this occurs, the weight on the key ring and
certain road conditions could cause the ignition switch to move out of the “ON” position to the accessory “ACC”
position.
If the ignition switch is pulled from the “ON” position to the “ACC” position while the vehicle is in motion, the engine
may stop running unexpectedly, increasing the risk of a crash. If a crash occurs under this condition, the airbags
may not deploy, increasing the risk of injury.
WHAT SUBARU WILL DO
Subaru will inspect and, if necessary, replace the ignition switch in your vehicle with a remedied one at no cost to
you.
WHAT YOU SHOULD DO
You should immediately contact any authorized Subaru retailer (dealer) for an appointment to have the ignition
switch in your vehicle inspected and, if necessary, replaced for free.
Until this recall repair has been performed, please remove all items from your key ring,
leaving only the vehicle key.
To minimize your inconvenience while the repair is being performed, please ask your retailer for alternative
transportation options.
HOW LONG WILL THE REPAIR TAKE?
The actual time to inspect and, if necessary, replace the ignition switch in your vehicle is approximately 36
minutes. However, your retailer can provide you with a better estimate of the overall time for this service visit, as it
may be necessary to make your vehicle available for a longer period of time.
Continued...
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 9 of 10
OWNER INFORMATION
Government regulations require that recall notifications be sent to the last known owner of record. That information
is based primarily on state registration and title data. If you are a lessor of this vehicle, federal regulations require
you to forward this notice to your lessee within ten days.
If you have moved or sold your vehicle, please update this information online at www.subaru.com, select
‘Customer Support,’ then select ‘Address Update’ or ‘Ownership Update’ from the drop-down menu.
IF YOU HAVE PREVIOUSLY PAID FOR A REPAIR
If you have already paid for repairs associated with this condition, you may be eligible for reimbursement.
Reimbursement consideration will be based on the amount an authorized Subaru retailer in your area would
charge for the same repair.
Please send the original service repair order, which has the name of the repair facility, date of repair, mileage
at the time of repair, complete 17-digit vehicle identification number (VIN), and your name, with correct mailing
address and telephone number to the address listed below.
Subaru of America, Inc.
Customer-Retailer Services Department, Attention: WUF-91 Recall
P.O. Box 9103, Camden, NJ 08101-9877
Please send original receipts only and retain a photocopy for your records. Please be assured that we will attempt
to process your reimbursement request as quickly as possible, but it may take up to 60 days for this process to be
completed.
IF YOU NEED FURTHER ASSISTANCE:
To locate the nearest Subaru retailer, you can access our website at www.subaru.com and select ‘Find a Retailer.’
If you need additional assistance, please contact us directly:
•
By e-mail: Go to www.subaru.com and select “Contact Us”
•
By telephone: 1-844-373-6614
•
Monday through Friday between 8:00 a.m. and 7:00 p.m. ET
•
By U.S. Postal mail: Write us at Subaru of America, Inc.
Attn: Customer-Retailer Services Department
P.O. Box 9103, Camden, NJ 08101-9877
To subscribe to the NHTSA Recall Notification email System, please go to: https://www-odi.nhtsa.dot.gov/nhtsa/
subscriptions.
Please contact us immediately if the Subaru retailer fails or is unable to make the necessary repairs free of charge.
You may also contact the Administrator, National Highway Traffic Safety Administration (NHTSA), 1200 New Jersey
Ave., SE, Washington, DC 20590 or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-4249153) or go to http://www.safercar.gov if you believe the Subaru retailer has failed or is unable to remedy your
vehicle without charge within a reasonable amount of time.
Your continued satisfaction with your Subaru is important to us. Please understand that we have taken this action
in the interest of your safety and your vehicle’s proper operation. We sincerely apologize for any inconvenience
this matter may cause and urge you to schedule an appointment as soon as possible.
Sincerely,
Subaru of America, Inc.
Notice to Lessors: Under Federal law the lessor of a vehicle who receives this letter must provide a copy of it to the vehicle lessee(s) within 10
business days from receipt. The lessor must also keep a record of the lessee(s) to whom this letter is sent, the date sent, and the applicable vehicle
identification number (VIN). (For the purposes of this section, a lessor means a person or entity that in the last twelve months prior to the date of this
notification has been the owner, as referenced on the vehicle’s title, of any five or more leased vehicles. A leased vehicle is a vehicle leased to another
person for a term of at least four months.)
A subsidiary of SUBARU CORPORATION
Bulletin Number: WUF-91R; Revised: 05/22/19
Page 10 of 10
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: WUF-91R
Replacement Service Bulletin Number:
MFR Communication Date: 2019-05-22
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
Last update on 2026-07-02 / Affiliate links / Images from Amazon Product Advertising API
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
Last update on 2026-06-30 / Affiliate links / Images from Amazon Product Advertising API
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
Last update on 2026-07-02 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.