00 SD Creator: how to set up and use the SD Creator for obtaining vehicle software updates via the
MirrorServer
00 19 22 2047812/6 June 25, 2019. Supersedes Technical Service Bulletin Group 00 number 19-15 dated
January 14, 2019 for reasons listed below.
Model(s)

Year

VIN Range

Vehicle-Specific Equipment

All

2010 - 2021

All

Not Applicable

Condition
REVISION HISTORY
Revision

Date

Purpose

6

-

Revised header (Added MY2021 and model)
Revised Technical Background (Updated information)
Revised Service (Updated link and added MIB2+)

5

01/14/2019

Revised Service (Updated link)

4

08/09/2018

Revised header data (Added models and model years)
Revised Condition (Added Note)
Revised Technical Background (Added system)
Revised Service (Added more information to Required Equipment and Selecting
the correct SD card)

The purpose of this bulletin is to explain the SD Creator program: how to set the program up and use it.
Note:
Only the K0942 software update for MMI3G+ is available for download. Older software updates for MMI3G+ are
not available for download and must be purchased from the Parts department.

Page 1 of 7
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Background
All software updates for MMI and FPK from MY15
onward will be available using the SD card creator as
long as the MMI is of the MIB platform. Some MMI3G+
software updates are also available for download (Figure
1). The Service section explains the process of setting up
and using the SD Creator program. If the program cannot
be installed due to IT restrictions, then the SD Cards
containing the software updates are available for
purchase via the Parts department.

Figure 1. SD Creator.

Production Solution
Not applicable.

Service
Required equipment:
 ODIS Service with VAS tester (SD Creator program can only run on a VAS tester with the ODIS Service at
the Dealership).
 If using a 6150A, an USB-to-SD card reader will need to be used due to the slow read rate of the internal SD
card slot of the 6150A. See the section below titled “6150A SD Card Slot Slow Read Rate Issue”.
 Valid MirrorServer Certificate installed on a VAS tester with the ODIS Service (certificate must not be
expired).
 Blank SD card, with enough capacity, to download the software update files (each update requires a separate
SD card).
 Part number of the software update. This is the service part number for the SD card in ETKA. The part
number can be found in the TSB or within ETKA.

Page 2 of 7
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Time to set up the program for the first time on the ODIS
machine:


Approximately 5 minutes.

Please see the following video: https://audiexternal.kzoplatform.com:443/swf/player/341 (Figure 2).

Figure 2. QR Code for supporting video.
Time to download software onto SD card:
 The time varies based on the size of the software update files & the type of internet connection. Typical
download time is around 30 minutes to 1 hour with a 3MB/s stable download connection. Keep in mind your
times can vary greatly based on the time of day due to heavy usage periods for the Internet Service Provider.
How to select the correct SD Card:
The first step is to obtain a blank SD card with enough space required for the software update. Typical SD card
sizes are listed below, but always reference the original TSB which suggests the software update. When the
download process is started, the SD Creator program will format and wipe all data from the SD card.
Please make sure to back up any important data which is already installed on the SD card before starting the
download process. It is important to note the download process cannot be started without an SD Card installed
in the VAS tester with ODIS Service.
 MIB1 High: 2-4GB
 MIB2 High Scale: 2-4GB
 MIB2 High Navigation: 4-8GB

Page 3 of 7
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

 MIB2+ High Navigation: 4-8GB
 RMC: 2-4GB
 MMI3G+: 0.5GB (500MB)
 FPK: 1-2GB
6150A SD Card Slot Slow Read Rate Issue:
The internal SD card slot on a 6150A cannot be used due to the slow read rate. The SD Creator will not allow
any SD card to be used when placed in the internal SD card slot of a 6150A due to the slow read rate of the slot.
Alternatively, the user can use a USB-to-SD card adapter that can be inserted into one of the USB 2.0 ports of
the computer. When choosing an adapter, ensure the adapter is at least USB 2.0 compliant (USB 3.0 will work
as well).
Installing the SD Creator (IT Administrator help may be required):
 Using a VAS tester with ODIS Service, open a web browser and navigate to
https://mirrorserver2.vwhub.com/dav/BTAC/Trade-Retail/Tools/SD-Creator/.
 If prompted for a security certificate then select the MirrorServer certificate for the machine.
 Within this folder, you will find the “SD Creator” install program labeled “setup_ V1.1.7.7.exe”. Click on this
file and save it to the desktop or another folder on the machine. If you are unable to download this file then
please contact your IT administrator.
 Once the file has successfully downloaded, install the program onto the VAS tester with ODIS Service by
double-clicking the file labeled “setup_ V1.1.7.7.exe”. If IT policies restrict the installation of programs on the
VAS tester with ODIS Service then please ask the IT administrator to perform the install.
 The AUDI AG created installation instructions and user manual are located in the same directory and is
labeled “2017_03_21_Benutzerhandbuch_SD_Creator_V_1.0_EN_.pdf”.

Page 4 of 7
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Once the program is installed it will place an icon labeled
“SD Creator” on the desktop:
 Open the application by double-clicking the icon.
 When prompted, select the drive letter for the SD card
(Figure 3 – item 1).
 Enter the support email address,
“[email protected]” (Figure 3 – item 2).
 Select the MirrorServer certificate by selecting “Select
certificate…” (Figure 3 – item 3).
 Enter the MirrorServer address (Figure 3 – item 4) by
using “https://mirrorserver2.vwhub.com” (without
quotes). Once set, the user can later verify this setting in
the server section listed under the “settings” tab.
 Select “Audi” in the “Brand” drop-down menu after item 4.
 Uncheck the box for “Show this dialog on every launch”
and select “Next”.

Figure 3. Initial Setup Screen.
Note:
When the “Support” button is pressed (Figure 4), an email will
automatically be generated along with any error logs (also
automatically attached). In the email, type a brief description
of the error experienced and then send the email. The email
will be sent to the support team at AoA.

Figure 4. Support button.

Page 5 of 7
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Using the SD Creator to download the software update files
 You will need the SD card part number listed in the Required Parts and Tools section of the original software
update TSB or by searching ETKA.
 Enter this part number into the “Part number” field with NO SPACES. The program will automatically find the
software files on the MirrorServer if entered correctly.
 For instance, if the SD card part number is 4M0 906 961 AE, then enter “4M0906961AE” into the part number
field. The program will automatically divide the part number and insert periods.
 Reference pages 15-18 of the user manual if you have any troubles with using the program.
 “2017_03_21_Benutzerhandbuch_SD_Creator_V_1.0_EN_.pdf”.
Tip: Typical setup time to download the data and have a working SD card is about 30 minutes to 1hr
depending on network speed. *Because of this, prepare the SD card long before starting the repair.*
Steps used by SD Creator once the download is started:
1. When you select the “Play/Start” button, the program will first format the SD card
2. Next, the program will start the download of software files from the MirrorServer and save them on the local
hard drive. Each file is broken up into approximately 100MB chunks and the program will check the files oneby-one to ensure they are not corrupted. If the internet connection is interrupted during the download, then
any of the files can become corrupted. If this happens the entire process will need to be started over,
beginning with the part number entry.
3. Once all the files are downloaded, they will be unpacked to the hard drive and extracted to the SD card.
4. The files are encrypted, thus you cannot manually unpack the files. The SD Creator program must perform
the unpacking.
5. The SD Creator will attempt to eject the SD card. Sometimes this fails. If this happens, then manually eject
the card from the ODIS machine.
6. From this point, the SD card is okay to use in the MMI.

Warranty
This TSB is informational only and not applicable to any Audi Warranty.

Additional Information
Page 6 of 7
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

All parts and service references provided in this TSB (2047812) are subject to change and/or removal. Always
check with your Parts Department and/or ETKA for the latest information and parts bulletins. Please check the
Repair Manual for fasteners, bolts, nuts, and screws that require replacement during the repair.
©2019 Audi of America, Inc. All rights reserved. The information contained in this document is based on the
latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes
at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites without the prior expressed written permission of the
publisher.

Page 7 of 7
© 2019 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.