GROUP

NUMBER

AUTOMATIC
TRANSMISSION
DATE

MODEL

Technical Service Bulletin
APRIL 2019

SUBJECT:

19-AT-008H
GENESIS (BH/DH)
GENESIS COUPE (BK)
EQUUS (VI)

AUTOMATIC TRANSMISSION SOLENOID DTC P0741, P0743, P0748,
P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841

This TSB supersedes TSB 16-AT-011 to update Applicable Vehicles and parts information.
Description: When servicing a vehicle with a “Check Engine light” and any of the DTCs listed
below, follow the Service Procedure and replace the related solenoid and E-module.

Applicable Vehicles:

2012~16 Genesis Sedan (BH/DH)
2013~16 Genesis Coupe (BK)
2012~16 Equus (VI)

DTC LIST & PARTS INFORMATION:
DTC

DESCRIPTION

PNC

PART NO.

45000

45000-*****

P0741

Torque converter clutch circuit performance or stuck off

P0743

Torque Converter Clutch Circuit Electrical

46202A

46313-3B01*

P0748

Pressure Control Solenoid Valve(VFS) A Electrical

46313A

46313-3B00*

P0753

Shift Control Solenoid Valve 'A' Electrical (UD/B)

46313

46313-4E50*

P0758

Shift Control Solenoid Valve 'B' Electrical (2-6/B)

46313

46313-4E50*

P075A

ON/OFF Solenoid (SS-A)

46313D

46313-3B03*

P0763

Shift Control Solenoid Valve 'C' Electrical (35R/C)

46313C

46313-4E70*

P0768

Shift Control Solenoid Valve 'D' Electrical (4&OD)

46313B

46313-4E60*

P0773

Shift Control Solenoid Valve 'E' Electrical (SS-A – 27B)

46313

46313-4E50*

P0841

Transmission Fluid Pressure Sensor/Switch A Circuit

N/A

TSB 14-AT-001

P2709

Shift Control Solenoid Valve 'F' Electrical (SS-B)

46313E

46313-4E51*

E-Module – BH 3.8L, BK 2.0L/3.8L

46305C

46305-4F1**

E-Module – BH 4.6L/5.0L, VI 5.0L

46305C

46305-4E1**

All

Circulate To: Service Manager, Warranty Manager, Service Advisors, Technicians, Fleet Repair

SUBJECT: ATM DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841

WARRANTY INFORMATION – Solenoid replacement:
MODEL
Genesis Sedan
(BH/DH)
Genesis Coupe (BK)
Equus (VI)

OP CODE OPERATION

45775R8T

Solenoid
valve assy.

OP TIME

CAUSAL PART

Refer to
WEBLTS
for current
LTS

Refer to part
numbers
on Page 1

NATURE CAUSE
CODE
CODE

13A

ZZ3

SERVICE PROCEDURE:
1.

Attach a GDS and select DTC Analysis and A/T menu. Record the DTC and description.
Delete the DTC.

2.

From the GDS home screen, select Data Analysis and A/T menu and the solenoid parameters
shown below. If the solenoids show:
 Continuous and changing output while driving, the wiring currently has no open/short
circuits. Go to Step 4.
 No continuous and changing output, go to Step 3.

3.

Visually check the wiring harness between the TCM and transmission for a damaged wire or
connector. Check for an open/short circuit.
 If so, repair or replace the ECM control harness and drive the vehicle to confirm the repair.
 If no damage is found, go to Step 4.

4.

Record the audio preset stations and disconnect the negative battery terminal.

TSB #: 19-AT-008H

Page 2 of 9

SUBJECT:

5.

ATM DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841

Lift the vehicle on a hoist.
Press the tab in the center of the latch and push
the latch upward.
Push the connector up to disconnect the
connector.

6.

Use an 8mm or 5/16” hex socket and remove the
drain plug and drain the ATF. Reinstall the drain
plug.
Torque: 17~18 lb.ft (2.3~2.5 kgf.m, 22~24 N.m)
Remove the bolts that secure the oil pan and
remove the pan.

7.

Remove the 10 bolts that secure the valve body
to the case and remove the valve body.

TSB #: 19-AT-008H

Page 3 of 9

SUBJECT: ATM DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841

8.

Remove 8 bolts and remove the E-module.

9.

P0841 - Fluid pressure switch only:
 If P0841 was recorded, update the TCM
according to TSB 14-AT-001.


If P0841 was not recorded, go to Step 10.

NOTICE
The pressure switch is no longer
available. Follow TSB 14-AT-001
and update the TCM.

10. Refer to the solenoid DTC recorded in Step 1
and replace the related solenoid.
Refer to the PNC in the parts catalog.
DTC
P0753
P0768
P0763
P0773
P0758
P2709
P075A
P0743
P0748

SOLENOID
UD
4&OD
35R
27
6
8LR
SS-A
DC
LP

TSB #: 19-AT-008H

PNC
46313
46313B
46313C
46313
46313
46313E
46313D
46202A
46313A

Page 4 of 9

SUBJECT:

ATM DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841

11. For UD, 4&OD, 35R, 27, 6 and 8LR solenoids:
Remove two bolts and remove the solenoid
support.

12. Use a magnet to remove the pin and remove the
related solenoid.
Install a new solenoid.
Reinstall the pin and the solenoid support.

13. For SS-A, DC and LP solenoids:
Use a 5mm hex socket to remove 4 bolts that
secure the support to the valve body and remove
the support.
Remove the related solenoid.
Install a new solenoid.
Reinstall the support.

TSB #: 19-AT-008H

Page 5 of 9

SUBJECT: ATM DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841

14. Install a new E-module and torque to
specification.
Torque: 7~9 lb.ft (1.0~1.2 kgf.m, 10~12 N.m)

15. Confirm that 5 O-rings are seated in the case.

16. Carefully align the manual valve to the shift lever
and reinstall the valve body.

TSB #: 19-AT-008H

Page 6 of 9

SUBJECT:

ATM DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841

17. Install 10 bolts and torque to specification.
Install the 3 long black bolts in the correct
location.
Torque: 7~9 lb.ft (1.0~1.2 kgf.m, 10~12 N.m)

18. Reconnect the harness connector and pull the latch down until it clicks (See Step 5).
19. Install the oil pan and torque the bolts to specification.
Torque: 7~8 lb.ft (1.0~1.2 kgf.m, 10~12 N.m)
20. Reconnect the negative battery terminal. Reset the audio preset stations.
21. Use an 8mm or 5/16” hex socket and remove the
fill plug and washer.
Shift into Park and lift the vehicle on a hoist.
Use a fluid pump or suction gun to add
approximately 4 quarts of SP-IV-RR ATF through
the fill plug.

NOTICE
Use only SP-IV-RR ATF, P/N
00232-19052.

TSB #: 19-AT-008H

Page 7 of 9

SUBJECT: ATM DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841

22. Remove the overflow plug.
Start the engine.
Add approximately 4~5 additional quarts of
SP-IV-RR ATF through the fill plug until the ATF
flows out.
Reinstall the fill plug and washer.
Torque: 27~33 lb.ft (3.7~4.6 kgf.m, 33~44 N.m)
Reinstall the overflow plug.
Torque: 16~18 lb-ft (2.3~2.5 kgf.m, 21~24 N.m)

23. Attach a GDS and select vehicle, Data Analysis and A/T menu and Oil Temperature Sensor.
24. Drive the vehicle until the ATF is at the low end of the range of 122~140°F (50~60°C).
25. Move the shift lever to “P” and leave the engine
idling. Raise the vehicle on a hoist.
Remove the overflow plug. The ATF level is
correct when the ATF flows out in a steady, thin
stream.

.

TSB #: 19-AT-008H

ATF TEMPERATURE = 122~140°F (50~60°C)
SHIFT LEVER IN “P” AND ENGINE RUNNING

Page 8 of 9

SUBJECT:

ATM DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841

26. Clear the codes and test drive the vehicle for two driving cycles (two key-on to key-off driving
cycles, including 1-2-3-4-5-6-7-8 upshifts and 8-7-6-5-4-3-2-1 downshifts). If the DTC returns,
perform the following repairs:
DTC

P0743
P0748
P0753
P0758 
P075A
P0763

P0768
.
P0773
P2709
P0841

REPAIR PROCEDURE

Replace the control wiring harness between the TCM and transmission. If
the solenoid DTC does not occur again, return the vehicle to the customer.
If the solenoid DTC returns again, replace the TCM.

27. Clear DTC in the BlueLink system per instructions of TSB 12-BE-005-2.
28. Drive the vehicle to confirm the proper operation of the transmission.

TSB #: 19-AT-008H

Page 9 of 9