JACK’ Digital HDTV Over-the-Air Antenna
wibuilt-in SureLock~ Digital TV Signal Meter

OA8200-White
0A8201-Black

SPECIFICATIONS

Dimensions: 11.257 x TOW x 12. 5°L Powered Amplifier +12 volt / 100 mA working
Weight 2.3 Ibs. Power supply Wail Mt Switch (incluced)

+ Mfr, # P1000 - power supply. white
Frequency Bands: VHF (47-230 Mhz) - 20 db gain

UHF 470-880 Mhz) - 25 db gain Enelosure/Mount: ASA-Automotive grade
Signal meter
Frequency Response: 40-862 Mhz (Ch 2-69)
OPERATION

The Wall Mount Power Injector is ¢ convenient way to

switch between your cable feed and over-the-air signals
from your JACK sntenns. 9

‘To use the Power Injector. simply turn the unit on with the
ONIOFF button. When on (button depressed), the power

light will turn green indicsting +12 volts to the antenns, snd
the over-the-air signsl from your JACK antenna will be fed 4
to the two TV outputs.

When off, the cable TV signs! will be fed to the two TV
outputs if wired for cable TV input

fy OT

YON: +12 volts sent to antenna
and JACK antenna signal is
passed to both TV outputs.

OFF: Cable signal is passed to both
TV outputs if cable input connected.

POSITIONING THE ANTENNA

Jum on sntenna power at wall mount plate

2. Tum on SureLock™ Signa! Meter power button
on side of rotations! knob enclosure

3. Rotate sttenustor dis! fully clockwise.

Step 4 Note: LED lights will illuminate from left (next to power} to right.
All LED lights may not illuminste depending on signsl strength.

4. Depress button on rotations! knob and rotate antenna.
until maximum number of LED lights illuminate on signs! meter.

5. Rotate sttenuator dis! counter clockwise until lest illuminated LED light flickers,
5. Rotate antenna to illuminate last flickering LED fight
7. Repeat steps 5 and 6 to pinpoint signal reception

8, Follow instructions for TV or converter box to scan for available channels
Page 1

2,
a>

OVERVIEW (FIG. 1)

1, Unpack and verify ail parts ere present.
2. Determine which adjustable connector you need to use

Roof thicknesses from 1 1/4° to 3 1/2" use assembly es shipped.

Roof thicknesses from 3 1/2" to 6° use the longer connector.
IMPORTANT! If using the fonger connector, install it now,

BEEORE INSTALLING BASE MOUNT ON ROOF
Pull out the existng adjustable connector from upper connector
located in the base mount.

Line up the tab with the angled surface ss shown st right and
insert the connector until it engages with the upper connector

Leave connector sticking out of base mount more than the
thickness of the roof.

Upper connector

This piece is inside:
the base mount

Angled surtace

For roots 3 1/2” to 6” ONLY!

Siecs ee tos trios feat
“connectors included.

For roof thicknesses 1 1/4” to 3.1/2"

use the assembly as shipped.

For roof thicknesses 3 1/2" to 6”

1-24" Hole

Page 2

EXTERIOR BASE MOUNT INSTALLATION (FIG. 2)

Hae pnt erie atl aires poral determining the most appropriate fastener to eeoure the base to the:
Later See eae ‘The inatatior Is for seating all holes
Ceara even alana responsible

1. Select on eras on the roof for the buse mount keeping in mind the following IMPORTANT POINTS:
4) The point of the base mount with the adjustable connector should face the front of the vehicle (Fig, 1)

b) The center of the roof hole must be at least 20" away from any object taller than 8" to provide clearance for the
antenna head to rotate freely, The center of the roof hole must also be at least &" from the edge of the root.

©) There must be room on the interior ceiling of the vehicle to attach the rotation knob and enclosure to the
adjustable connector. The interior enclosure can be mounted In any direction

2 Dill @ 2° hole perpendicular to the root surface all the Way thru the vehicle roof where the adjustable connector will go
(A 3 3/4" hole will work for flat roofs, If'roof haw # pitch (up to 3 degrees) you may need # larger hole up to 2 1/4" )

2. Inside the vahichn, pleos the enclosure base over the hole and against the calling in the position # will Be mounted Mark the
comx hole on the ceiling Enierge the interior rot hole only at thie location fo accommeadate the coms cable where it will
‘exit the roof and antar the enclosure base (Fiy 3)

4. On tha roof of the vehicle, carefully pull out the adjustable connector 30 Mt will axtend beyond the thicknaas of the roof wher
the base mount is installed |t must axtenc thru the roof to mllow installation of interior components Exact length will be
adjuated when Interior components are installed

5. Cannect the coax from the antenna input of the power supply switch to ine open connection on the spitter in the base
mount

IMPORTANT! In Step f, ring eal sealant must not get on the adjustable connector,

6. Apply seslunt to fing seal and base mount, and fill the comx channel with sealant (Butyl tape may be used Wy combination
with wealant) Carefully pivon br hase sock ik pontion waa soniobs connector me dinouk poloe tara tha edt fale
and into the interior of the vehicle. Make ount onnec d
towarda the front of the vehicle.

7. Cantar the adjustable connector in root hole and fasten the base mount to the roof, Use the mounting holes in the base
mount 08 9 guide to inaisil the fastener (determined by the installer) into the root Make sure the base mount i pamied ail
the Way around and the comm channel is fully sasied as well

7 Mount lacing Want of wervene

Apply sealant te Gotten of Maree
‘ort foatmen caine evel rhea el
(Piast tape ervey ale He it

Page 3

INTERIOR ENCLOSURE INSTALLATION (FIG. 3)

1. Press knob button and remove knob from enclosure base.

2 Make sure the coax exits the roof thru the enlarged portion of the roof hole and route the cosx thru the coax hole in the
enclosure base. Place the enclosure base around the adjustable connector end sgainst ceiling (The enclosure base will
‘seat around the raised circle on the adjustable connector.) Fasten the enclosure to the ceiling with four inchided screws.

3. Press the knob button and push knob onto the end of the adjustable connector.

. The knob will fit into the raised ring on the enclosure. )

Fasten knob to connector with screw.

4 Route the coax sround the raised ring as shown and connect the coax to the RF connector on the SureLock™ signs! meter.

5. Optional: If desired, apply the decal to the enclosure cover.

© Carefully align the cover and snap into piace. (Make sure not to damage or bend LED lights or pinch the coax cable.)

Page 4

WALL MOUNT POWER SWITCH INSTALLATION (FIG. 4)

41. Wire the wall mount power switch ss shown,

WIRING DIAGRAM - BOTTOM VIEW

(#12 VDC and Ground require #10-12 female spade connectors)