TIS Service Bulletin

Page 1 of 3

SI B54 07 18
Special Roofs

November 2018
Technical Service

PANORAMIC SUNROOF DOES NOT OPEN OR CLOSE
New information provided by this revision is preceded by this symbol

.

This Service Information bulletin replaces SI B54 07 18 dated August 2018
What’s New:
• G02 Added
• Procedure changed with release of ISTA 4.14.1x
• Warranty information changed

MODEL
G01 (X3)

G02 (X4)

SITUATION
The panoramic sunroof will not open or close. There are no faults stored for the panoramic sunroof.

CAUSE
A software error in the Roof Function Center (FZD).

CORRECTION
Update the vehicle software using ISTA 4.14.1x or higher.

PROCEDURE
1. Perform diagnosis using the latest version of ISTA. Work through any associated test modules if needed.
If no faults are stored, continue to step 2.
2. Program the vehicle using ISTA 4.14.1x (I-Level 18-11-5xx) or higher.
Note that ISTA will automatically reprogram and code all programmable control modules that do not have the
latest software.
Always connect a BMW-approved battery charger/power supply (SI B04 23 10 ).
For information on programming and coding with ISTA, refer to CenterNet / TIS / Technical Documentation /
Diagnostics and Programming / Programming Documentation.

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/48... 12/3/2018

TIS Service Bulletin

Page 2 of 3

PARTS INFORMATION
Do not replace parts. Parts replacement will not provide a solution.

WARRANTY INFORMATION
Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.

Defect Code:

6131740200

Labor Operation:

Labor Allowance:

Description:

00 00 006

Refer to KSD2/AIR

Performing “vehicle test” (with vehicle diagnosis
system – checking faults) (Main work)

Refer to KSD2/AIR

Performing “vehicle test” (with vehicle diagnosis
system – checking faults) (Plus work)

Refer to KSD2/AIR

Connect an approved battery charger/power
supply (indicated in KSD2 as “Charging battery”)

Refer to KSD2/AIR

Programming/encoding control unit(s)

Or:
00 00 556
And:
61 21 528
And:
61 00 730

If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead of 00
00 006.
Refer to KSD2/AIR for the corresponding flat rate unit (FRU) allowances.
Vehicle Programming and Encoding
During the same workshop visit, if a vehicle also requires another Technical Campaign or repair that also
includes programming and encoding the control units, the programming procedure may only be invoiced one
time.
A. The programming procedure automatically reprograms and encodes all vehicle control modules which do not
have the latest software i-level. If one or more control module failures occur “during” this programming
procedure:
• Please claim this “consequential” control module-related repair work under the defect code listed in this
bulletin with the applicable KSD2/AIR labor operations.
Please explain this additional work (The why and what) on the repair order and in the claim comments section.
B. For control module failures that occurred “prior” to performing this programming procedure:
• When “covered” under an applicable limited warranty, claim this control module-related repair work using the
applicable defect code and labor operations (including diagnosis) in KSD2/AIR.
Posted: Monday, November 5, 2018

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/48... 12/3/2018

TIS Service Bulletin

Page 3 of 3

[ Copyright ©2018 BMW of North America, Inc. ]

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/48... 12/3/2018