L-SB-0040-18

October 31, 2018

2019 UX200/UX250h Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2019

UX200, UX250H

ADDITIONAL INFORMATION

Introduction

This bulletin contains the vehicle specific pre-delivery services for 2019 model year UX200 and
UX250h vehicles. Additionally, refer to the applicable Pre-Delivery Service (PDS) Check Sheet for
services to be performed.

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

N/A

Not Applicable to Warranty

–

–

–

–

Procedures



Front License Plate and Mounting Bracket Installation ........................................................... 2



D/C Cut Fuse Installation ......................................................................................................... 4



Front and Rear Emergency Towing Eyelet Removal ............................................................... 6



Front and Rear Emergency Towing Eyelet Hole Cover Installation......................................... 8

© 2018 Lexus, a division of Toyota Motor Sales, USA

Page 1 of 8

L-SB-0040-18

October 31, 2018

Page 2 of 8

2019 UX200/UX250h Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation

The front license plate mounting bracket and two self-tapping screws for the 2019 model year
UX200 and UX250h are stored in the luggage compartment of the vehicle at the assembly plant.
For states that require a front license plate, install the bracket and bolts on the bumper cover
during PDS according to the following procedure.
1. Align holes “A” of the mounting bracket with the lower set of dimples on the front
bumper cover.
NOTE
 There are two sets of dimples on the front bumper cover. Use the lower set of dimples.
 Holes “A” are used to install the mounting bracket onto the radiator grille.
 Holes “B” are used to install the front license plate onto the mounting bracket.

2. Install the mounting bracket onto the front bumper cover at holes “A” using the two
self-tapping screws.
Figure 1.

B
c

B
c

B
c

A

A

B
c

A
c

A
c

2
c

3
c

1
c

2
c

3
c

1

Mounting Bracket

2

Low er Dim ple

3

Self-tapping Screw

© 2018 Lexus, a division of Toyota Motor Sales, USA

1
c

L-SB-0040-18

October 31, 2018

Page 3 of 8

2019 UX200/UX250h Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation (continued)

3. Install the front license plate onto the mounting bracket at holes “B” using
two noncorroding bolts with the following dimensions:
Nominal Length: 15.0 mm (0.59 in.)
Diameter: 6.0 mm (0.24 in.)
Figure 2.

2
c

2
c

1
c

1

Front License Plate

2

Bolt

1
c

Figure 3.

2

1

1

Nom inal Length

2

Diam eter

© 2018 Lexus, a division of Toyota Motor Sales, USA

L-SB-0040-18

October 31, 2018

Page 4 of 8

2019 UX200/UX250h Pre-Delivery Service (PDS)
D/C Cut Fuse Installation

To minimize battery discharge during transportation and storage, the D/C cut fuses (30A) have
been removed at the assembly plant and temporarily stored in the blank spaces of the relay
block in the engine compartment.
During PDS, remove the D/C cut fuses (30A) from the blank spaces of the relay block in the
engine compartment and install them in the locations shown.
Gasoline Vehicles

With the ignition switch OFF, install the D/C cut fuses (30A) into their original locations in the
engine compartment relay block.
Figure 4. UX200

2
c
3
c

1
c

1

Relay Block

3

2

Rem ove These D/C Cut Fuses (30A)

Install D/C Cut Fuses (30A) Here (Original Location)

NOTE
 While the vehicle is stored at the dealership, disconnect the negative (–) battery terminal to prevent
battery discharge. Refer to Service Bulletin No. L-SB-0108-17, Battery Maintenance During PDS.
 If the D/C cut fuses (30A) are installed with the ignition switch in the “IG-ON” position,
Diagnostic Trouble Codes (DTCs) will be detected. Clear the DTCs.

© 2018 Lexus, a division of Toyota Motor Sales, USA

L-SB-0040-18

October 31, 2018

Page 5 of 8

2019 UX200/UX250h Pre-Delivery Service (PDS)
D/C Cut Fuse Installation (continued)
Hybrid Vehicles

With the ignition switch OFF, install the D/C cut fuses (30A) into their original locations in the
engine compartment relay block.
Figure 5. UX250h

2
c
3
c

1
c

1

Relay Block

3

2

Rem ove These D/C Cut Fuses (30A)

Install D/C Cut Fuses (30A) Here (Original
Location)

NOTE
 While the vehicle is stored at the dealership, disconnect the negative (–) battery terminal to
prevent battery discharge. Refer to Service Bulletin No. L-SB-0108-17, Battery Maintenance
During PDS.
 If the D/C cut fuses (30A) are installed with the ignition switch in the “IG-ON” position, DTCs will
be detected. Clear the DTCs.

© 2018 Lexus, a division of Toyota Motor Sales, USA

L-SB-0040-18

October 31, 2018

Page 6 of 8

2019 UX200/UX250h Pre-Delivery Service (PDS)
Front and Rear Emergency Towing Eyelet Removal

1. Remove the front and rear emergency
towing eyelets from the front and rear
bumpers by turning them counterclockwise.

Figure 6.

HINT
If it is difficult to loosen the front emergency
towing eyelet, use a steel bar.

1
c

2
c

1

Front Em ergency Towing Eyelet

2

Rear Em ergency Towing Eyelet

© 2018 Lexus, a division of Toyota Motor Sales, USA

L-SB-0040-18

October 31, 2018

Page 7 of 8

2019 UX200/UX250h Pre-Delivery Service (PDS)
Front and Rear Towing Eyelet Removal (continued)

2. Place one of the removed emergency towing eyelets into the luggage tray in the
luggage compartment.
HINT
Dispose of the other removed emergency towing eyelets.

Figure 7.

1
c

1

1
c

Em ergency Towing Eyelet

© 2018 Lexus, a division of Toyota Motor Sales, USA

1
c

L-SB-0040-18

October 31, 2018

Page 8 of 8

2019 UX200/UX250h Pre-Delivery Service (PDS)
Front and Rear Emergency Towing Eyelet Hole Cover Installation

1. Install the front and rear emergency towing
eyelet hole covers, which are stored in the
glove compartment, onto the front and
rear bumpers.

Figure 8.

B
c

A. Insert the arrow-shaped part of the
emergency towing eyelet hole cover “A”
into the eyelet hole “B” as shown.
A
c

B. Install the emergency towing eyelet
hole cover to the hole of the bumper.

1
c

HINT
Make sure the front emergency eyelet
towing cover is installed in the front, and
the rear emergency eyelet towing cover
is installed in the rear.

A
c

B
c
2
c

A

Arrow-shaped Part

B

Eyelet Hole

1

Front Em ergency Towing Eyelet Hole Cover

2

Rear Em ergency Towing Eyelet Hole Cover

© 2018 Lexus, a division of Toyota Motor Sales, USA