T-SB-0145-18

November 30, 2018

2019 Prius Prime Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2019

Prius Prime

ADDITIONAL INFORMATION

Introduction

Pre-Delivery Service (PDS) is a critical step in satisfying our dealership’s new car customers.
Customer feedback indicates the following areas deserve special attention when performing PDS:





Careful inspection for paint chips/scratches and body dents/dings.
Proper operation of electrical accessories (including interior light, clock, and radio reset).
Interior cleanliness.
Proper function of mechanical systems.

Customer retention and proper maintenance of vehicles are and have always been a major focus
for Toyota. To help remind customers that regular service is essential to the proper maintenance
of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing
this, customers will be reminded to return to your dealership for service. Your current service
reminder sticker may be used. (See PDS Check Sheet “Final Inspection and Cleaning.”)
A new PDS Check Sheet has been developed for the 2019 model year Prius Prime. Some check
points have been added, expanded, or clarified. Bulletins are available for items in bold type.

Precaution

The Prius Prime has unique operating modes, so always follow the precautions below when
performing the PDS operation:


The Prius Prime contains high-voltage (200 ~ 650 volts) AC and DC systems. All high-voltage
wiring and connections are orange in color. Do not carelessly touch these orange-colored
wiring harnesses and connectors.



The gasoline engine may start up and shut down suddenly whenever the Ready light is
illuminated. Be sure to press the “P” position switch, apply the parking brake, press the
Power switch in order to turn off the hybrid system (the Ready light is off), and remove
the ignition key before working in the engine compartment.

Precaution (continued)

© 2018 Toyota Motor Sales, USA

Page 1 of 6

T-SB-0145-18

November 30, 2018

Page 2 of 6

2019 Prius Prime Pre-Delivery Service (PDS)


The hybrid transaxle, engine radiator, and inverter radiator may reach high temperatures
during inspection. Carefully observe all caution labels and instructions on
these components.



Be sure to place the gear selector into “P” (press the P switch) at all times unless otherwise
instructed. When the gear selector is in the “N” position, the hybrid vehicle battery will not
charge even if the gasoline engine is operating.



When leaving the vehicle, press the P position switch, apply the parking brake, and press the
Power switch in order to turn off the hybrid system (the Ready light is off). Remove the
ignition key.



Air vents are provided on the package tray behind the rear seatback to cool the hybrid vehicle
battery. Do not block these air vents.



Do not splash water on the electric components in the engine compartment.

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

001013

Pre-Delivery Service (PDS)

1.4

–

–

–

Warranty Policy

If the need for additional repairs or adjustment is noted during PDS, the required service should
be performed under warranty. Reimbursement will be managed under the warranty policy.
The Warranty Policy and Procedures Manual requires that you maintain the completed
Prius Prime PDS Check Sheet in the customer’s file. If you cannot produce a completed form
for each retailed vehicle upon TMS and/or Region/Distributor audit, the PDS payment amount will
be subject to debit.
An additional Repair Order completed in conjunction with normal PDS must have time
punch/flags for service. If multiple repairs are performed, separate time flags must be punched for
each repair.

© 2018 Toyota Motor Sales, USA

T-SB-0145-18

November 30, 2018

Page 3 of 6

2019 Prius Prime Pre-Delivery Service (PDS)
Required Tools & Equipment
REQUIRED EQUIPMENT

SUPPLIER

Techstream 2.0*
Techstream Lite

PART NUMBER

QTY

TS2UNIT
ADE

Techstream Lite (Green Cable)

TSLITEPDLR01
TSLP2DLR01

* Essential SST.

NOTE
 Only ONE of the Techstream units listed above is required.
 Software version 13.20.018 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787.

Battery Inspection

1. Install D/C cut fuse* – see Check Sheet

Functional Operation

Apply parking brake, cycle ignition “IG-ON,” place gear selector in “R,” turn on lights and rear
defogger, unlock all doors, and release fuel door.
1. Check dome, courtesy, map, and sun visor lights*
2. Check warning/indicator lights, gauges, and horn
3. Check windshield wipers and washers
4. Check headlights, instrument lights, turn signals, emergency flashers, and brake lights
5. Check inside/outside rear view mirror operation/adjustment
6. Check USB and 12V power outlets
Check the power outlet using an electrical accessory designed for this use.
7. Check audio/navigation*/backup camera* systems and set clock
For navigation, set the destination search area to local position.
8. Check multi-information display and trip information on center display*
9. Check sliding roof*

© 2018 Toyota Motor Sales, USA

1

T-SB-0145-18

November 30, 2018

Page 4 of 6

2019 Prius Prime Pre-Delivery Service (PDS)
Walkaround Inspection

Starting at the left front door, check window and door lock operation from master power switch, if
equipped. Continue around vehicle in a counterclockwise direction checking each door and window
operation, child door locks, seat belts, interior condition, all lights, and luggage compartment
contents. Finish by checking headlight aim.
1. Check Smart Key System – T-SB-0185-17
2.
3.
4.
5.
6.
7.
8.
9.
10.

Check window operation
Check that engine starts with all keys
Check that child safety door locks are in normal (unlocked) position*
Check seats and seat belt operation
Check rear defogger/rear view mirror defogger*
Check side marker, tail, backup, and license plate lights
Check luggage compartment light* and trim appearance
Check emergency tire puncture repair kit, jack, and tool installation
Check headlight aim
Refer to the Repair Manual for procedures.

11.

Under Hood

1. Check engine oil level
2. Check brake fluid level
Visually inspect using see-through reservoirs.
3.
4.
5.
6.
7.

Check engine coolant level
Check inverter coolant level
Check windshield washer fluid level
Inspect for fuel, oil, coolant, and other fluid leaks
Check battery State-Of-Charge (SOC) using digital battery system analyzer
Refer to Service Bulletin No. T-SB-0195-17, Battery Maintenance During PDS.
NOTE
Battery SOC should be a minimum of 75%. Please enter the SOC reading on the space provided on
the Check Sheet and attach the printout to the Check Sheet.

Battery Maintenance

1. Perform HV battery check and maintenance – T-SB-0197-17

© 2018 Toyota Motor Sales, USA

T-SB-0145-18

November 30, 2018

Page 5 of 6

2019 Prius Prime Pre-Delivery Service (PDS)
Under Vehicle (On Hoist)

1. Remove disc brake anti-rust covers/anti-corrosion wheel film* – PD017-04
Visually inspect rotors for rust.
NOTE
For best rotor rust prevention, retain wheel film on vehicle until just before delivery to the customer.

2. Inspect tires for defects/damage
3. Initialize Tire Pressure Warning System (TPWS) – see Check Sheet
4.
5.
6.
7.
8.

Install wheel caps*
Inspect for fuel, oil, coolant, and other fluid leaks
Inspect under the vehicle for damage, rust etc.
Visually check bolts and nuts on chassis and powertrain for looseness
Install rubber body plugs (stored in glove box or center console)*

9. Check hybrid transaxle fluid level

Road Test

A complete road test helps promote customer satisfaction. Drive vehicle over a variety of road
surfaces and driving conditions. Check for unusual noise and driving performance.
1. Check cold engine operation
Check starting and fast idle operation performance.
2. Check engine operation during warm-up
Check that engine operates smoothly during warm-up.
Check for unusual noise, engine vibration, rough idle, etc.
3. Check engine operation at normal operating temperature
Check engine performance over a broad range of driving conditions, including idle quality,
acceleration, cruise, and deceleration.
4. Calibrate Intelligent Clearance Sonar System* – see Check Sheet
5. Check hybrid transaxle operation
6. Check brake and parking brake operation
Check brake function, including unusual noise, parking brake performance, and all related
brake system indicator lights.
7. Check steering operation and off-center/vehicle pull/flutter
Check steering function.
Check steering off-center/vehicle pull/flutter.

© 2018 Toyota Motor Sales, USA

T-SB-0145-18

November 30, 2018

Page 6 of 6

2019 Prius Prime Pre-Delivery Service (PDS)
Road Test (continued)

8. Inspect for abnormal noise and vibration
9. Inspect for squeaks and rattles
10. Check front and rear* heater and A/C operation
11. Check cruise control operation*
Check cruise control, including ON-OFF switch, Set/Coast, Resume/Accel, and
Cancel functions.
12. Check front seat heater/ventilation operation*
Final Inspection and Cleaning

1. Remove interior protective covers, unnecessary labels, tags, etc. (Remove protective covers
just before delivery to the customer)
Remove plastic covers from door panels, seats, head restraints, and sun visors, as required.
Remove labels, tags, and stickers (except those containing owner information).
NOTE
Customer information labels, such as the fuel caution, airbag warnings, and bumper labels, must be
left on the vehicle until delivery to a retail customer.

2. Visually inspect all interior parts for installation, damage, fit, dirt, etc.
3. Verify floor mat application and install using retaining clips* – T-SB-0188-17
4. Verify green light is illuminated on SOS (Safety Connect) button*
NOTE
The vehicle may arrive with a hanger requesting inspection of the Safety Connect system. If the
system is working properly and the green light is illuminated, disregard the hanger.

5. Remove Rapgard™ and clear protective bumper film*
Ensure that all glue residue is removed.
6. Wash and clean vehicle
7. Inspect paint finish for scratches, chips, rust, dents, damage, etc.
8. Inspect exterior body parts for proper installation, damage, rust, etc.
9. Place service reminder sticker on inside of windshield, top left corner
Complete the mileage or date recommendation and apply the service reminder sticker
to the inside of the windshield, top left corner. You may use your current service
reminder sticker.
10. Install front license plate and mounting bracket* – see Check Sheet
11. Place Owner’s Manual portfolio* in glove box
12. Perform Techstream Health Check
Perform Health Check to ensure that Diagnostic Trouble Codes (DTCs) are not present.
Health Check results can be printed for the customer at delivery, or for the dealer file, using
the Diagnostic Report function.
* Inspect or install w hen equipped or required.

© 2018 Toyota Motor Sales, USA