Classification:

Reference:

FE17-001a

Date:

NTB18-033a

November 28, 2018

2014 – 2019 ROGUE; ACCELERATOR PEDAL VIBRATION
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.

APPLIED VEHICLES:

2014 – 2019 Rogue (T32)
This bulletin does not apply to Rogue Hybrid.

IF YOU CONFIRM
A vibration from the accelerator pedal between 1600 - 2000 RPM.

ACTION
Install the new brake booster vacuum tube and hose listed in the PARTS INFORMATION
section of this bulletin.

IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/6

SERVICE PROCEDURE
Electronic
throttle
control
actuator

1. Loosen the air duct assembly (aft)
screw clamps.

2. Separate the rubber air duct assembly
(aft) from the mass air flow sensor and
the electronic throttle control actuator.

Air duct assembly
(aft) screw clamps

Air duct
assembly (aft)

Mass air
flow sensor

Figure 1

EVAP test port
hose clip

3. Release the EVAP test port hose from
clip.

Breather
hose
clamp

4. Release the breather hose clamp from
air duct assembly (aft).
Breather hose
5. Remove the breather hose from air duct
assembly (aft).
Figure 2

Air duct assembly (aft) clip locations
6. Pull the air duct assembly (aft) straight
up on the passenger side then the
driver side to release the clips.

7. Remove the air duct assembly (aft)
from vehicle.

Figure 3

2/6

NTB18-033a

8. Remove the acoustic absorber clips from cowl.
NOTE:
 There are 2 different possible acoustic absorber designs.


Clips located in the approximate area shown in Figure 4 and Figure 5.
Design 1

Design 2

Acoustic absorber
clip location

Acoustic absorber
clip locations

Acoustic absorber

Figure 5

Figure 4

Clamp

Brake booster
vacuum hose

9. Release the clamp from the brake
booster vacuum hose at the intake
manifold.

10. Remove the brake booster vacuum
hose from the intake manifold.

Figure 6

3/6

NTB18-033a

Brake booster
vacuum hose

11. Release the clamp from the brake
booster vacuum hose at the brake
booster.

12. Remove the brake booster vacuum
hose from the brake booster.

Clamp

Figure 7

13. Release the 2 brake booster vacuum
tube mounting clips.
NOTE: The passenger side mounting
clip is located under the acoustic
absorber in the approximate location
shown in Figure 8.
Mounting clip
locations
14. Remove the brake booster vacuum
tube from the vehicle.
Figure 8

NOTE:
 The new brake booster vacuum tube
will come with a new rubber hose for
the brake booster side.


The original rubber hose on the
intake manifold side will need to
be transferred to the new metal
brake booster vacuum tube.



All original hose clamps will need to
be transferred to the new brake
booster vacuum tube.

Old brake booster vacuum tube and hose

Intake
manifold side

New brake booster vacuum tube and hose
Figure 9

4/6

NTB18-033a

15. Locate the plastic sleeve installed on
the metal section of the new brake
booster vacuum tube.
NOTE: The old brake booster vacuum
tube is not equipped with the plastic
sleeve. The plastic sleeve will be used
in the next step to properly locate the
new brake booster vacuum line.
Plastic sleeve
Figure 10

Driver side clip
16. Install the new brake booster vacuum
tube.

Plastic sleeve

17. Attach the driver side clip to the new
brake booster vacuum tube with the
plastic sleeve positioned on the driver
side of the clip.

Brake
booster
Figure 11

18. Reinstall all other components in the reverse order of removal.

5/6

NTB18-033a

PARTS INFORMATION
DESCRIPTION

PART NUMBER

QUANTITY

TUBE-VAC BRAKE BOOSTER

47401 - 7FA0A

1

HOSE-VAC BRAKE BOOSTER

47471 - 7FA0A

1

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Replace Brake Booster
(1)
PF14AA
(2)
(2)
(3)
Vacuum tube/hose
(1) Reference the Parts Information table above, and use the TUBE-VAC BRAKE
BOOSTER as the Primary Failed Part (PFP).
(2) Use the Symptom and Diagnostic codes that apply to the repair actually performed.
(3) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT.

AMENDMENT HISTORY
PUBLISHED DATE

REFERENCE

DESCRIPTION

April 18, 2018

NTB18-033

Original bulletin published.

November 28, 2018

NTB18-033a

APPLIED VEHICLES section revised.

6/6

NTB18-033a