Page 1 of 3

SI B11 04 13
Engine

June 2016
Technical Service

N63TU Engine: Engine Oil Consumption

New information provided by this revision is preceded by this symbol

.

This Service Information bulletin supersedes SI B11 04 13 dated November 2014.
MODEL

F01 (7 Series Sedan)

F02 (7 Series
Sedan)

F06 (6 Series Gran
Coupe)

F12 (6 Series
Convertible)

F13 (6 Series
Coupe)

Produced from 6/2012 to
12/2012

F07 (5 Series Gran
Turismo)

SITUATION

The customer complains that the “low engine oil” message is displayed too frequently.
CAUSE

The cause is related to, but not limited to, one or more of the following components and systems
shown below:
z

Turbocharger

z

Crankcase ventilation

z

Engine gasket leaks

z

Internal engine tolerances and sealing

z

Improper filling or topping up

Use the troubleshooting procedure below to help identify the cause.
PROCEDURE

1. The crankcase ventilation system utilized in these engines cannot be measured with
consistency because the system does not incorporate a regulating valve (spring with
diaphragm). The crankcase pressure is regulated by an orifice in the crankcase ventilation
tubes, and the vacuum will vary with crankcase pressure changes. Checking the operation of
this unregulated system can only be performed by visually inspecting for loose connections
or cracks in the system components. Generally active leakages will have an oily residue
surrounding that affected area. The use of a smoke machine may also be helpful when trying
to locate leakages in this system.
If the system appears to be operating properly, proceed to the next step.

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/342... 7/7/2016

Page 2 of 3

2. Remove the intake boots from the turbochargers. Inspect the turbochargers for excessive
engine oil; refer to the attachment for identification of acceptable levels of engine oil. If the
levels are unacceptable, enter a TC Engine PuMA case for authorization of the turbocharger
(s). Photos of the engine oil will need to be attached to each TC case.
If the engine oil residue level is acceptable when compared to the attachment, proceed to step
3.
3. Submit a TC Engine Case with “N63TU Engine Oil Consumption” in the subject line and
wait for a response.
Do not replace any internal engine components or any components that require
TeileClearing authorization.
The TC case description must contain the following information:
z

Whether there is evidence of external leaks

z

Crankcase ventilation system inspection results

z

Photos of the turbo oil residue inside turbo(s)

z

Detailed history of engine oil top-up, e.g., date, mileage and amount of engine oil added on
each visit

z

Oil consumption measurement results which include date and mileage of the start and end of
the measurement.

MEASURING OIL CONSUMPTION

Vehicles with N63TU – Measuring oil level electronically using the oil level test plan in
ISTA/D
Applicable models and I-levels:
z

F01 and F02 with the N63T with I-Level F001-13-03-501 or higher

z

F06, F07, F12 and F13 with I-Level F010-13-03-501 or higher

Test plan path:
1. Select “Service Function.”
2. Select “Drive.”
3. Select “Motor Electronics.”
4. Select “Motor Oil.”
5. Select “Oil Level.”
6. Select “Continue.”

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/342... 7/7/2016

Page 3 of 3

7. Follow the steps as directed in the test plan to complete the measurement.
The test plan will identify the actual oil level, and will advise the amount of engine oil needed to
correctly fill the engine when conducting an oil consumption test. After topping up the engine oil,
perform the test plan one more time to ensure the oil level is correct. The vehicle must be driven
1,000 miles or until the next low engine oil message appears (whichever comes first). The oil level
test plan must be performed again to identify the consumption level in the distance driven.
Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN
number of the vehicle.
Manual oil consumption measurement
If the vehicle has an I-Level that does not match or is higher than the l-Levels mentioned above, the
engine oil must be drained, measured and the engine oil refilled.
The vehicle must be driven 1,000 miles or until the next low engine oil message appears
(whichever comes first). The oil must be drained again and measured to identify consumption level.
Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN
number of the vehicle.
WARRANTY INFORMATION

Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light
Trucks or the BMW Certified Pre-Owned Program as applicable:
z

For the cases described under paragraph 1 and 2: Claim this work with the applicable defect
code(s) and labor operations listed in KSD2.

z

For the case described in paragraph 3: TeileClearing will guide you through the appropriate
repair or replacement of engine components.

If TeileClearing directs you replace the complete engine, please use defect code 11 25 02 69 00 for
your claim submission unless directed otherwise.
ATTACHMENTS

View PDF attachment B110413_Turbo_Oil_Leakage.
[ Copyright ©2016 BMW of North America, Inc. ]

https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/342... 7/7/2016