NHTSA ID Number: 10146412
Manufacturer Communication Number: LTB01064NAS2
TSB/Document Date: 2018-11-05
Summary
A judder from the vehicle at low speeds when steering may be evident.
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
LT B 0 1 0 6 4 N A S 2
TECHNICAL BULLETIN
28 AUG 2008
© Jaguar
Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians
with the knowledge, tools, and equipment required to do the job properly and safely. It informs these
Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a
Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Land
Rover service facility to determine whether this bulletin applies to a specific vehicle.
I N F O R M AT I O N
This reissue replaces all previous versions. Please destroy all previous versions.
SECTION:
205-02
S U B J E C T/ C O N C E R N :
Judder From Active On-Demand Coupling
AFFECTED VEHICLE RANGE:
MODEL:
Discovery Sport (LC)
MODEL YEAR:
2016 Onwards
VIN:
613684 Onwards
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
APPLICABILITY:
Vehicles With: Active On-Demand Coupling
1/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
MODEL:
Range Rover Evoque (LV)
MODEL YEAR:
2016-2017
VIN:
143755-241619
APPLICABILITY:
Vehicles With: Active On-Demand Coupling
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
A judder from the vehicle at low speeds when steering may be evident.
CAUSE:
This may be caused by water ingress through the Active On-Demand Coupling breather, allowing
water to contaminate the oil in the Active On-Demand Coupling.
ACTION:
Should a Customer express this concern, follow the Workshop Procedure below.
PA RTS :
PART NUMBER
DESCRIPTION
QUANTITY
LR019450
Valve
1
LR051347
1
FB108076
Bolt M8 x 35 mm
9
LR001193
Driveshaft bolt M8 X 45 mm
6
LR054941
Active On-Demand Coupling - Statoil - SL01-301
3
TOOLS:
Refer to Workshop Manual for any required special tools.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
2/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
WARRANT Y:
NOTES:
Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to JLR claims submission
system to obtain the latest repair time.
The JLR Claims Submission System requires the use of causal part numbers. Labor only claims
must show the causal part number with a quantity of zero.
DESCRIPTION
Active On-Demand Coupling - Clean
SRO
44.24.89.44
TIME (HOURS)
1.5
CONDITION CODE
49
CAUSAL PART
LR073538
NOTE:
Normal Warranty procedures apply.
WORKSHOP PROCEDURE:
1
Raise the vehicle on a ramp (see TOPIx Workshop Manual section 100-02: Jacking and Lifting Lifting).
2
Remove the exhaust system (see TOPIx Workshop Manual section 309-00: Exhaust System Removal and Installation).
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
3/22
8/28/2018
3
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Remove the Rear Drive Unit (RDU) heat shield.
Torque: 10 Nm,
4
CAUTIONS:
Mark the position of the driveshaft flange in relation to the drive pinion flange.
To avoid damage to the joint or gaiter, do not allow the driveshaft to hang.
Make sure that the driveshaft is supported with suitable retaining straps.
NOTE:
Discard the bolts.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
4/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Position the driveshaft to the side.
Torque: 40 Nm.
5
NOTE:
Do not discard the bolts.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
5/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Remove the RDU cross member.
Torque: 175 Nm [2]
Torque: 25 Nm [4]
6
WARNING:
Wear eye protection when using compressed air.
NOTES:
Use compressed air to make sure that the breather is clean and free from foreign
material.
Make sure that the area around the component is clean and free of foreign material.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
6/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Remove the Active On-Demand Coupling breather pipe.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
7/22
8/28/2018
7
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Disconnect the RDU electrical connector.
8
CAUTION:
Be prepared to collect escaping fluids.
NOTE:
Make sure that the area around the component is clean and free of foreign material.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
8/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Remove the Active On-Demand Coupling sump.
Torque: 29 ± 4 Nm.
9
CAUTION:
Be prepared to collect escaping fluids.
NOTE:
Make sure that the area around the component is clean and free of foreign material.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
9/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Remove the Active On-Demand Coupling from the RDU.
Torque: 29 Nm.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
10/22
8/28/2018
10
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Disconnect the electrical connector from the Active On-Demand Coupling.
11
NOTE:
Make sure that the area around the component is clean and free of foreign material.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
11/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Remove the motor from the Active On-Demand Coupling.
Torque: 10 Nm.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
12/22
8/28/2018
12
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Use compressed air to make sure that the breather is clean and free from foreign material.
13
NOTES:
Make sure that the area around the component is clean and free of foreign material.
Use compressed air to blow into each hole to disperse the water between the clutch
plates.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
13/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Clean the Active On-Demand Coupling using lint-free cloths and compressed air.
14
NOTES:
Make sure that the area around the component is clean and free of foreign material.
Lower the RDU until it can not be lowered any further.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
14/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Lower the RDU to make sure all the RDU fluid is drained from the RDU.
15
NOTES:
Make sure that the area around the component is clean and free of foreign material.
Make sure to clean the oil ways in the RDU.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
15/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Clean the RDU in the areas shown using lint-free cloth and compressed air.
16
NOTE:
Make sure that all oil ways, breathers and components are clean and free from foreign
material before installation.
To install, reverse the removal steps.
17
NOTE:
Make sure that the area around the component is clean and free of foreign material.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
16/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Remove the Active On-Demand Coupling sump fill plug.
18
NOTE:
Make sure that the area around the component is clean and free of foreign material.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
17/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Fill the Active On-Demand Coupling sump.
Capacity: 780 ml.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
18/22
8/28/2018
19
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Install the Active On-Demand Coupling sump fill plug.
Torque: 12 Nm.
20
Remove the rear left fender splash shield (see TOPIx Workshop Manual section 501-08:
Exterior Trim and Ornamentation - Rear Fender Splash Shield).
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
19/22
8/28/2018
21
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Disconnect the breathers from the retaining clips and position to one side.
22
NOTE:
Discard the removed part of the breather.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
20/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Mark the breather pipe (A) 10mm in the position shown.
1 Cut the breather (A) using a sharp knife in the area shown.
23
NOTE:
Make sure the new breather canister hose is installed to its maximum position.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
21/22
8/28/2018
LTB01064NAS2 - Judder From Active On-Demand Coupling | TOPIx
Install the new breather canister as shown.
24
Position the breather pipes and connect to the retaining clips.
25
Install the rear left fender inner splash shield (see TOPIx Workshop Manual section 501-08:
Exterior Trim and Ornamentation - Rear Fender Splash Shield).
https://topix.jaguar.jlrext.com/topix/content/document/view?id=923343
22/22
- 📌【We are Here for You】Dear valued customer, please be...
- 🚀【5X Faster Next-Level Hardware, Same as MK900/ MX...
- 🔥【3000+ Active Tests = MK900/MK900BT but...
- 📢【2026 U.S. Version, All-in-One as MK808S/ MK808Z...
- 🔥【28+ Hot Services for 150+ Brands】Same as MaxiCOM...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: LTB01064NAS2
Replacement Service Bulletin Number:
MFR Communication Date: 2018-08-28
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: STEERING
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
- 🔥 Historical lowest pr-ice now on sa-le--hot se-lling.
- 【🎈𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝟲 𝗲𝘀𝘀𝗲𝗻𝘁𝗶𝗮𝗹 𝗿𝗲𝘀𝗲𝘁 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗔𝗕𝗦 𝗕𝗹𝗲𝗲𝗱𝗶𝗻𝗴, 𝗢𝗶𝗹 𝗥𝗲𝘀𝗲𝘁, 𝗘𝗣𝗕, 𝗦𝗔𝗦, 𝗧𝗵𝗿𝗼𝘁𝘁𝗹𝗲 𝗥𝗲𝗹𝗲𝗮𝗿𝗻, 𝗮𝗻𝗱 𝗕𝗠𝗦—𝗽𝘂𝘁𝘁𝗶𝗻𝗴 𝗽𝗿𝗼𝗳𝗲𝘀𝘀𝗶𝗼𝗻𝗮𝗹-𝗴𝗿𝗮𝗱𝗲 𝗺𝗮𝗶𝗻𝘁𝗲𝗻𝗮𝗻𝗰𝗲 𝗯𝗮𝗰𝗸 𝗶𝗻 𝘆𝗼𝘂𝗿 𝗵𝗮𝗻𝗱𝘀.】Spongy brakes? Stuck oil light? Parking brake won't release? Off-center steering? Rough idle after battery disconnect? Draining battery? IF745 handles all with a few taps. One tool covers six dealer-level resets, saving hundreds in labor costs. ❗ NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨ 𝗜𝗙𝟳𝟰𝟱 𝗴𝗼𝗲𝘀 𝗯𝗲𝘆𝗼𝗻𝗱 𝗯𝗮𝘀𝗶𝗰 𝗰𝗼𝗱𝗲 𝗿𝗲𝗮𝗱𝗶𝗻𝗴 𝘄𝗶𝘁𝗵 𝟭𝟬 𝗶𝗻𝘁𝗲𝗴𝗿𝗮𝘁𝗲𝗱 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗗𝗧𝗖 𝗟𝗼𝗼𝗸𝘂𝗽, 𝗜/𝗠 𝗥𝗲𝗮𝗱𝗶𝗻𝗲𝘀𝘀, 𝗙𝗿𝗲𝗲𝘇𝗲 𝗙𝗿𝗮𝗺𝗲, 𝗟𝗶𝘃𝗲 𝗗𝗮𝘁𝗮, 𝗢𝟮𝗦, 𝗢𝗕𝗠, 𝗘𝗩𝗔𝗣, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Pulling a code tells you something is wrong. IF745 tells you what the code means, when the fault happened, and what data surrounds it. Pass emissions with one I/M Readiness tap. Freeze the fault moment with Freeze Frame. Monitor live sensor data in real time. Turn cryptic codes into clear answers.
- 【🛒 𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝗳𝘂𝗹𝗹-𝘀𝘆𝘀𝘁𝗲𝗺 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀 𝗮𝗰𝗿𝗼𝘀𝘀 𝗮𝗹𝗹 𝗺𝗼𝗱𝘂𝗹𝗲𝘀—𝗲𝗻𝗴𝗶𝗻𝗲, 𝗔𝗕𝗦, 𝗮𝗶𝗿𝗯𝗮𝗴, 𝘁𝗿𝗮𝗻𝘀𝗺𝗶𝘀𝘀𝗶𝗼𝗻, 𝘀𝘁𝗲𝗲𝗿𝗶𝗻𝗴, 𝘀𝘂𝘀𝗽𝗲𝗻𝘀𝗶𝗼𝗻, 𝗯𝗼𝗱𝘆 𝗲𝗹𝗲𝗰𝘁𝗿𝗼𝗻𝗶𝗰𝘀, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Warning lights on but you don't know why? Skip the $100+ diagnostic fee at the shop. Run a complete self-check from your driveway. IF745 reads and clears fault codes, retrieves ECU info, and displays live data from every accessible module—delivering a full vehicle health report in minutes, without leaving home.
- 【✅𝗜𝗙𝟳𝟰𝟱 𝗳𝗲𝗮𝘁𝘂𝗿𝗲𝘀 𝗮 𝟳-𝗶𝗻𝗰𝗵 𝗱𝗶𝘀𝗽𝗹𝗮𝘆, 𝗲𝗿𝗴𝗼𝗻𝗼𝗺𝗶𝗰 𝗱𝗲𝘀𝗶𝗴𝗻, 𝗪𝗶-𝗙𝗶 𝘂𝗽𝗱𝗮𝘁𝗲𝘀, 𝗮𝗻𝗱 𝘇𝗲𝗿𝗼 𝘀𝘂𝗯𝘀𝗰𝗿𝗶𝗽𝘁𝗶𝗼𝗻 𝗳𝗲𝗲𝘀 𝗳𝗼𝗿 𝗵𝗮𝘀𝘀𝗹𝗲-𝗳𝗿𝗲𝗲 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀.】Large screen means no squinting. Intuitive navigation and customizable data displays put key info at your fingertips. Wi-Fi delivers lifetime free updates without a computer. No recurring fees. No hidden costs. Just a reliable tool that works as hard as you do.
This product presentation was made with AAWP plugin.