High Pressure (HP) fuel feed pipe - 2012-13MY

1

LR101734

High Pressure (HP) fuel feed pipe - 2014-15MY

1

ZZZ001

* Fluids

1

TOOLS:



Jaguar Land
Rover-approved
Midtronics battery
power supply

Jaguar Land
Rover-approved
diagnostic tool
with latest SDD
Software
Management Pack


Inline Diagnostic
Unit 2 (IDU2)

WARRANT Y:

https://topix.jaguar.jlrext.com/topix/content/document/view?id=918907

5/11

8/2/2018

LTB01101NAS3 - Poor Engine Performance | TOPIx

NOTES:
* - a maximum allowance of $83.75 USD or local equivalent has been provided to cover the
cost of 6.2 liters of engine oil. Claim using Sundry Code ‘ZZZ001’.
* - a maximum allowance of $48.13 USD or local equivalent has been provided to cover the
cost of 4.25 liters of engine coolant. Claim using Sundry Code ‘ZZZ001’.
* LR2 (L359) only- a maximum allowance of $38.38 USD or local equivalent has been
provided to cover the cost of 2.0 liters of steering fluid. Claim using Sundry Code ‘ZZZ001’.
Use the Jaguar Land Rover claims submission system for Field Service Action program
eligibility requiring a Powertrain Control Module (PCM) software update. If eligible, perform
and claim the update as per that program.

NOTES:
Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to JLR claims submission
system to obtain the latest repair time.
The JLR Claims Submission System requires the use of causal part numbers. Labor only claims
must show the causal part number with a quantity of zero.

DESCRIPTION

SRO

TIME
(HOURS)

CONDITION
CODE

CAUSAL
PART

Update ECU - Powertrain Control Module (PCM)

12.90.13

0.2

01

LR049655

Cylinder pressures - Check - With diagnostic
equipment

12.25.01.02

0.6

01

LR049655

Engine - Replace - LR2 (L359)

12.41.02

11.8

01

LR049655

Engine - Replace - Range Rover Evoque (L538;
2012-13MY)

12.41.02

10.0

01

LR049655

Engine - Replace - Range Rover Evoque (L538;
2014-15MY)

12.41.02

10.3

01

LR049655

NOTE:
Normal Warranty procedures apply.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918907

6/11

8/2/2018

LTB01101NAS3 - Poor Engine Performance | TOPIx

DIAGNOSTIC PROCEDURE 'A':

CAUTIONS:
A Jaguar Land Rover-approved Midtronics battery power supply must be connected to the
vehicle battery during diagnosis / module programming.
All ignition ON/OFF requests must be performed. Failure to do so may cause damage to
control modules in the vehicle.
1

Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle start
up battery.

2

3

Switch the ignition ON (engine not running).

NOTE:
The Jaguar Land Rover-approved diagnostic tool must be loaded with SDD 154.00
Software Management Pack v298 (or later).
Connect the Jaguar Land Rover-approved diagnostic tool to the vehicle and begin a new
session.

4

Follow the on-screen prompts, allowing the diagnostic tool to read the VIN, identify the
vehicle, and initiating the data collect sequence.

5

NOTE:
The DTC listed in the table below are an indication of an engine misfire. If any of these
are stored, they must be investigated and rectified before continuing with this bulletin
(see TOPIx Workshop Manual section 303-01A / -01B: Engine - GTDi 2.0L Petrol Diagnosis and Testing - Engine - GTDi 2.0L Petrol).
Read the DTC.

https://topix.jaguar.jlrext.com/topix/content/document/view?id=918907

7/11

8/2/2018

LTB01101NAS3 - Poor Engine Performance | TOPIx

If DTC P0300, P0301, P0302, P0303, P0304, and/or P1315 is NOT stored, go to
Diagnostic Procedure 'B' below.
If DTC P0300, P0301, P0302, P0303, P0304, and/or P1315 is stored, go to Step 6
below.
DIAGNOSTIC TROUBLE CODE
(DTC)

DIAGNOSTIC TROUBLE CODE
(DTC)

DIAGNOSTIC TROUBLE CODE
(DTC)

P0030-00

P0458-00

P2097-02

P0031-00

P0459-00

P2231-00

P0032-00

P0496-00

P2237-00

P00D1-00

P0497-00

P2237-02

P0131-00

P064D-08

P2237-64

P0132-00

P064D-16

P2243-00

P0133-00

P064D-17

P2251-00

P0134-00

P064D-86

P228C-77

P0192-00

P2096-00

P228D-77

P0193-00

P2096-02

P2626-00

P0444-00

P2097-00

6

Follow all on-screen instructions.

7

If the hyperlink is not available:
1 Select Diagnosis from the Session Type screen.
2 Select the Selected Symptoms tab.
3 Select one of the following symptoms:
Powertrain - Engine system - Engine performance
4 Select continue.
5 Select the Recommendations tab.
6 Select Run to perform the 'Special Applications - Inline diagnostic unit 2 relative
compression test - GTDi 2.0L Petrol' option.

https://topix.jaguar.jlrext.com/topix/content/document/view?id=918907

8/11

8/2/2018

LTB01101NAS3 - Poor Engine Performance | TOPIx

If the vehicle does pass the compression test, investigate other potential causes
of the customer concern (see TOPIx Workshop Manual section 303-01:
Diagnosis and Testing - Engine - GTDi 2.0L Petrol).
When the investigation and rectification has been completed, go to
Diagnostic Procedure 'B' below.
If the vehicle does not pass the compression test, go to the Workshop
Procedure below.

WORKSHOP PROCEDURE:

NOTES:
This Workshop Procedure is only applicable to vehicles which DID NOT pass the compression
test after following the relevant steps above.
Prior approval is required before continuing with the Workshop Procedure; submit a Fixed
Right Enhanced Diagnostic (FRED) request for the replacement of the engine.
1

Remove the engine (see TOPIx Workshop Manual section 303-01A / -01B: Engine - GTDi 2.0L
Petrol - Removal - Engine).

2

Remove the engine ancillaries from the engine (see TOPIx Workshop Manual section 303-01A
/ -01B: Engine - GTDi 2.0L Petrol - Disassembly - Engine).

3

Install the engine ancillaries onto the replacement engine (see TOPIx Workshop Manual
section 303-01A / -01B: Engine - GTDi 2.0L Petrol - Assembly - Engine).

4

Install the replacement engine (see TOPIx Workshop Manual section 303-01A / -01B: Engine GTDi 2.0L Petrol - Installation - Engine).

5

NOTE:
Follow steps 6-13 of the filling section.

https://topix.jaguar.jlrext.com/topix/content/document/view?id=918907

9/11

8/2/2018

LTB01101NAS3 - Poor Engine Performance | TOPIx

Fill the engine with new engine oil (see TOPIx Workshop Manual section 303-01A / -01B:
Engine - GTDi 2.0L Petrol - Engine - Engine Oil Draining and Filling).
6

Go to Diagnostic Procedure 'B'.

DIAGNOSTIC PROCEDURE 'B':

CAUTIONS:
A Jaguar Land Rover-approved Midtronics battery power supply must be connected to the
vehicle battery during diagnosis / module programming.
All ignition ON/OFF requests must be performed. Failure to perform these steps may cause
damage to control modules in the vehicle.

NOTE:
Use the Jaguar Land Rover claims submission system for Field Service Action program eligibility
requiring a Powertrain Control Module (PCM) software update. If eligible, perform and claim the
update as per that program.
1

Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle start
up battery.

2

3

Switch the ignition ON (engine not running).

NOTE:
The Jaguar Land Rover-approved diagnostic tool must be loaded with SDD 154.00
Software Management Pack v298 (or later).
Connect the Jaguar Land Rover-approved diagnostic tool to the vehicle and begin a new
session.

https://topix.jaguar.jlrext.com/topix/content/document/view?id=918907

10/11

8/2/2018
4

LTB01101NAS3 - Poor Engine Performance | TOPIx

Follow the on-screen prompts, allowing the diagnostic tool to read the VIN, identify the
vehicle, and initiating the data collect sequence.

5

NOTE:
If the Powertrain Control Module (PCM) software is at the latest level, this Step cannot
be performed.
If the hyperlink is not available:
1 Select Diagnosis from the Session Type screen.
2 Select the Selected Symptoms tab.
3 Select one of the following symptoms:
Electrical - Instruments - Warning lamps - Engine malfunction lamp - Lamp
illuminated or
Electrical - Instruments - Information and message center - Message display
area - Powertrain
4 Select continue.
5 Select the Recommendations tab.
6 Select Run to perform the 'Configure existing module - Powertrain control module'
option.

6

Follow all on-screen instructions until the application finishes successfully.
1 When prompted, select the Clear DTCs option following completion of the software
download.
2 When all tasks are finish, go to the next Step.

7

Exit the current session.
1 Select the Session tab.
2 Select the Close Session option.

8

Disconnect the diagnostic tool and battery power supply from the vehicle.

https://topix.jaguar.jlrext.com/topix/content/document/view?id=918907

11/11