NHTSA ID Number: 10146325
Manufacturer Communication Number: 0504-18
TSB/Document Date: 2018-10-29
Summary
0504-18 Fuel System - Fuel Injectors
05 04-18
1
05 04-18
SUBJECT
DATE
Fuel System - Fuel Injectors
May 2018
Additions, Revisions, or Updates
Publication Number / Title
DDC-SVC-MAN-0194
DDC-SVC-MAN-0198
Platform
GHG17
DD5
934912(C)
GHG17
DD8
Section Title
Change
Removal of the Fuel
Injectors
Changes due to new tools and different steps
Inspection of the Fuel
Injectors
This is a new section
Installation of the Fuel
Injectors
Changes due to new tools and different steps
Removal of the Fuel
Injectors
Changes due to new tools and different steps
Inspection of the Fuel
Injectors
This is a new section
Installation of the Fuel
Injectors
Changes due to new tools and different steps
All information subject to change without notice.
05 04-18
Copyright © 2018 DETROIT DIESEL CORPORATION
3
2 Removal of the Fuel Injector
2
Removal of the Fuel Injector
Table 1.
Service Tools Used in the Procedure
Tool Number
Tool Name
W936589003300 or DSN930E17004
Injector Puller
Tool Graphic
W936589013300
Injector Seal Installer
W936589033300 or DSN930E17002
Injector Heat Protection Sleeve Tool Kit
Remove as follows:
4
All information subject to change without notice.
Copyright © 2018 DETROIT DIESEL CORPORATION
05 04-18
05 04-18
1. Electrical Connector
2. Header With Calibration Codes
3. Injector Inlet O-ring
4. Injector Body O-ring
5. Fuel Return Port
6. Injector Tip
Figure 1. Fuel Injector
WARNING: PERSONAL INJURY
To prevent the escape of high pressure fuel that can penetrate skin, ensure the engine has been
shut down for a minimum of 10 minutes before servicing any component within the high pressure
circuit. Residual high fuel pressure may be present within the circuit.
1. Shut off the engine, apply the parking brake, chock the wheels, and perform any other applicable safety steps.
CAUTION: ELECTRICAL SHOCK
To avoid injury from electrical shock, use care when connecting battery cables. The magnetic
switch studs are at battery voltage.
2. Disconnect the batteries.
3. Open the hood.
4. If necessary, remove the bumper end(s). Refer to the Original Equipment Manufacturer (OEM) procedures.
WARNING: FIRE HAZARD
Do not power wash or steam clean the engine bay in the area of vehicle electrical components,
unless specified by vehicle manuals or service literature. Power washing/steam cleaning can
permanently damage these components, which could result in fire, personal injury, or property
damage.
5. Steam clean the rocker cover and rocker cover mounting area.
6. Remove the air compressor resonator and the rocker cover. Refer to section "Removal of the Rocker Cover".
All information subject to change without notice.
05 04-18
Copyright © 2018 DETROIT DIESEL CORPORATION
5
2 Removal of the Fuel Injector
7. Disconnect the fuel injector electrical wiring harness from the fuel injectors and position aside. Refer to section
"Removal of the Fuel Injector Wiring Harness".
8. Remove the high pressure fuel injector feed lines. Refer to section "Removal of the High Pressure Fuel Injector
Lines".
9. Remove the fuel injector hold-down bolt (1). Discard bolt.
10. Using tool W936589003300 or DSN930E17004, lift the fuel injector clamp and fuel injector from its seat in the
cylinder head.
11. Inspect for the copper heat protection sleeve on the injector tip; if present, remove and discard. If the copper sleeve is
missing, use tool W936589033300 or DSN930E17002 to extract it from the cylinder head and discard.
12. Cover the fuel injector hole in the cylinder head to keep out foreign material.
NOTICE: Avoid cleaning (wire brushing etc.) the fuel injector tip spray holes to prevent damage and plugging.
13. Using a clean rag soaked with clean diesel fuel, carefully remove any carbon material from the fuel injector exterior.
NOTICE: Fuel injector O-ring seals, fuel injector clamp bolts and the copper heat protection sleeves are
considered one-use items and cannot be reused. Any time a fuel injector is removed, the fuel injector bolt, two
fuel injector O-ring seals and copper heat protection sleeve must be replaced with new parts. Failure to replace
the O-ring seals, heat protection sleeve and bolt can result in leakage.
14. Inspect the fuel injector body for visible damage. Replace the fuel injector if damaged.
15. If the fuel injector is intended to be reused, remove and discard the two fuel injector O-rings and the copper sleeve.
6
All information subject to change without notice.
Copyright © 2018 DETROIT DIESEL CORPORATION
05 04-18
05 04-18
3
Inspection of the Fuel Injector
Inspect as follows:
1. Visually inspect the fuel injector body for cracks or damage. If damage is found, replace the injector.
2. Visually inspect for debris in the fuel inlet or signs of fuel contamination in the fuel inlet. If contamination is found,
further troubleshooting is required.
3. Visually inspect the injector tips for cracks or damage from excessive heat. If damage is found, replace the injector.
4. Visually inspect the threads of the fuel injector inlet. If the threads are damaged, replace the injector.
All information subject to change without notice.
05 04-18
Copyright © 2018 DETROIT DIESEL CORPORATION
7
4 Installation of the Fuel Injector
4
Installation of the Fuel Injector
Table 2.
Service Tools Used in the Procedure
Tool Number
Tool Name
W936589013300
Injector Seal Installer
W936589033300
Injector Heat Protection Sleeve Tool Kit
1. Electrical Connector
2. Header With Calibration Codes
3. Injector Inlet O-ring
Tool Graphic
4. Injector Body O-ring
5. Fuel Return Port
6. Injector Tip
Figure 2. Fuel Injector
Install as follows:
8
All information subject to change without notice.
Copyright © 2018 DETROIT DIESEL CORPORATION
05 04-18
05 04-18
NOTE: Ensure excess fuel is removed from the top of the piston dome before fuel injector installation.
1. If the fuel system, cooling system, or lubrication system is contaminated; refer to the appropriate troubleshooting.
NOTICE: The inside of the fuel injector cup and cylinder head bore should be cleaned and inspected for damage
or leakage of coolant before installation of the fuel injector.
2. Check to make sure the fuel injector cup and cylinder head bore are thoroughly clean.
3. If the fuel injector is being replaced, record the fuel injector calibration code, the injector part number, and note the
cylinder location where the injector will be installed.
4. If the fuel injector is being replaced, remove the fuel injector nozzle tip protector. Apply a thin coat of acid-free grease
or clean engine oil to the fuel injector seal rings and then use W936589013300 (Fuel Injector O-ring Installer) to
install them onto the fuel injector. Make sure they are properly seated.
5. Using tool W936589033300, install the copper heat protection sleeve on the fuel injector tip.
6. Install the fuel injector and clamp as an assembly into its respective fuel injector bore. Align the clamp over the bolt
hole, install the new bolt into fuel injector clamp and snug until the fuel injector fully seats, then release the fuel
injector bolt. DO NOT torque.
7. Install the high pressure fuel injector feed lines. Refer to section "Installation of the High Pressure Fuel Injector
Lines".
8. Torque the fuel injector hold-down bolt to 25 N·m (18 lb·ft) + 90 degree torque turn.
9. Install the fuel injector wiring harness. Refer to section "Installation of the Fuel Injector Wiring Harness".
10. If the fuel injector was replaced, input the fuel injector calibration code and injector part number that were recorded
earlier into DiagnosticLink ® using the service routine.
All information subject to change without notice.
05 04-18
Copyright © 2018 DETROIT DIESEL CORPORATION
9
4 Installation of the Fuel Injector
11. If the fuel injector was replaced because of a tip failure or leak, the EGR cooler must be cleaned. Refer to section
"Cleaning of the Exhaust Gas Recirculation Cooler".
12. Install the rocker cover. Refer to section "Installation of the Rocker Cover".
13. Install the air compressor resonator. Refer to section "Installation of the Air Compressor Resonator".
CAUTION: ELECTRICAL SHOCK
To avoid injury from electrical shock, use care when connecting battery cables. The magnetic
switch studs are at battery voltage.
14. Connect the batteries.
WARNING: PRESSURIZED FUEL
To avoid injury to eye or face, wear a face shield or goggles when conducting a pressure test.
15. Prime the fuel system. Verify repair. Refer to section "Priming the Fuel System".
16. If necessary, install the bumper end(s). Refer to the Original Equipment Manufacturer (OEM) procedures.
17. Close hood.
10
All information subject to change without notice.
Copyright © 2018 DETROIT DIESEL CORPORATION
05 04-18
05 04-18
5
Removal of the Fuel Injector
Table 3.
Service Tools Used in the Procedure
Tool Number
Tool Name
W936589003300 or DSN930E17004
Injector Puller
W936589013300
Injector Seal Installer
W936589033300 or DSN930E17002
Injector Heat Protection Sleeve Tool Kit
All information subject to change without notice.
05 04-18
Copyright © 2018 DETROIT DIESEL CORPORATION
Tool Graphic
11
5 Removal of the Fuel Injector
1. Electrical Connector
2. Header With Calibration Codes
3. Injector Inlet O-ring
4. Injector Body O-ring
5. Fuel Return Port
6. Injector Tip
Figure 3. Fuel Injector
Remove as follows:
WARNING: PERSONAL INJURY
To prevent the escape of high pressure fuel that can penetrate skin, ensure the engine has been
shut down for a minimum of 10 minutes before servicing any component within the high pressure
circuit. Residual high fuel pressure may be present within the circuit.
1. Shut off the engine, apply the parking brake, chock the wheels, and perform any other applicable safety steps.
CAUTION: ELECTRICAL SHOCK
To avoid injury from electrical shock, use care when connecting battery cables. The magnetic
switch studs are at battery voltage.
2. Disconnect the batteries.
3. Open the hood.
4. If necessary, remove the bumper end(s). Refer to the Original Equipment Manufacturer (OEM) procedures.
WARNING: FIRE HAZARD
Do not power wash or steam clean the engine bay in the area of vehicle electrical components,
unless specified by vehicle manuals or service literature. Power washing/steam cleaning can
permanently damage these components, which could result in fire, personal injury, or property
damage.
5. Steam clean the rocker cover and rocker cover mounting area.
12
All information subject to change without notice.
Copyright © 2018 DETROIT DIESEL CORPORATION
05 04-18
05 04-18
6. Remove the air compressor resonator and the rocker cover. Refer to section "Removal of the Rocker Cover".
7. Disconnect the fuel injector electrical wiring harness from the fuel injectors and position aside. Refer to section
"Removal of the Fuel Injector Wiring Harness".
8. Remove the high pressure fuel injector feed line and discard. Refer to section "Removal of the High Pressure Fuel
Injector Lines".
9. Remove the fuel injector hold-down bolt (1). Discard bolt.
10. Using tool W936589003300 or DSN930E17004, lift the fuel injector clamp and fuel injector from its seat in the
cylinder head.
11. Inspect for the copper heat protection sleeve on the injector tip; if present, remove and discard. If the copper sleeve is
missing, use tool W936589033300 or DSN930E17002 to extract it from the cylinder head and discard.
12. Cover the fuel injector bore in the cylinder head to keep out foreign material.
NOTICE: Avoid cleaning (wire brushing etc.) the fuel injector tip spray holes to prevent damage and plugging.
13. Using a clean rag soaked with clean diesel fuel, carefully remove any carbon material from the fuel injector exterior.
NOTICE: The fuel injector O-ring seals, fuel injector clamp bolt and the copper heat protection sleeve are
considered one-use items and cannot be reused. Any time a fuel injector is removed, the fuel injector bolt, two
fuel injector O-ring seals and copper heat protection sleeve must be replaced with new parts. Failure to replace
the O-ring seals, heat protection sleeve and bolt can result in leakage.
14. Inspect the fuel injector body for visible damage. Replace the fuel injector if damaged.
15. If the fuel injector is intended to be reused, remove and discard the two fuel injector O-rings and the copper sleeve.
All information subject to change without notice.
05 04-18
Copyright © 2018 DETROIT DIESEL CORPORATION
13
6 Inspection of the Fuel Injector
6
Inspection of the Fuel Injector
Inspect as follows:
1. Visually inspect the fuel injector body for cracks or damage. If damage is found, replace the injector.
2. Visually inspect for debris in the fuel inlet or signs of fuel contamination in the fuel inlet. If contamination is found,
further troubleshooting is required.
3. Visually inspect the injector tips for cracks or damage from excessive heat. If damage is found, replace the injector.
4. Visually inspect the threads of the fuel injector inlet. If the threads are damaged, replace the injector.
14
All information subject to change without notice.
Copyright © 2018 DETROIT DIESEL CORPORATION
05 04-18
05 04-18
7
Installation of the Fuel Injector
Table 4.
Service Tools Used in the Procedure
Tool Number
Tool Name
W936589013300
Injector Seal Installer
W936589033300
Injector Heat Protection Sleeve Tool Kit
1. Electrical Connector
2. Header With Calibration Codes
3. Injector Inlet O-ring
Tool Graphic
4. Injector Body O-ring
5. Fuel Return Port
6. Injector Tip
Figure 4. Fuel Injector
Install as follows:
All information subject to change without notice.
05 04-18
Copyright © 2018 DETROIT DIESEL CORPORATION
15
7 Installation of the Fuel Injector
NOTE: Ensure excess fuel is removed from the top of the piston dome before fuel injector installation.
1. If the fuel system, cooling system, or lubrication system is contaminated; refer to the appropriate troubleshooting.
NOTICE: The inside of the fuel injector cup and cylinder head bore should be cleaned and inspected for damage
or leakage of coolant before installation of the fuel injector.
2. Check to make sure the fuel injector cup and cylinder head bore are thoroughly clean.
3. If the fuel injector is being replaced, record the fuel injector calibration code, the injector part number, and note the
cylinder location where the injector will be installed.
4. If the fuel injector is being replaced, remove the fuel injector nozzle tip protector.
5. Apply a thin coat of acid-free grease or clean engine oil to the fuel injector seal rings and then use W936589013300
(Fuel Injector O-ring Installer) to install them onto the fuel injector. Make sure they are properly seated.
6. Using tool W936589033300, install the copper heat protection sleeve on the fuel injector tip.
7. Install the fuel injector and clamp as an assembly into its respective fuel injector bore. Align the clamp over the bolt
hole, install the new bolt into fuel injector clamp and snug until the fuel injector fully seats, then release the fuel
injector bolt. DO NOT torque.
8. Install the high pressure fuel injector feed line. Refer to section "Installation of the High Pressure Fuel Injector Lines".
9. Torque the fuel injector hold-down bolt to 25 N·m (18 lb·ft) + 90 degree torque turn.
10. Install the fuel injector wiring harness. Refer to section "Installation of the Fuel Injector Wiring Harness".
11. If the fuel injector was replaced, input the fuel injector calibration code and injector part number that were recorded
earlier into DiagnosticLink ® using the service routine.
16
All information subject to change without notice.
Copyright © 2018 DETROIT DIESEL CORPORATION 05 04-18
05 04-18
12. If the fuel injector was replaced because of a tip failure or leak, the EGR cooler must be cleaned. Refer to section
"Installation of the Exhaust Gas Recirculation Cooler".
13. Install the rocker cover. Refer to section "Installation of the Rocker Cover".
14. Install the air compressor resonator. Refer to section "Installation of the Air Compressor Resonator".
CAUTION: ELECTRICAL SHOCK
To avoid injury from electrical shock, use care when connecting battery cables. The magnetic
switch studs are at battery voltage.
15. Connect the batteries.
WARNING: PRESSURIZED FUEL
To avoid injury to eye or face, wear a face shield or goggles when conducting a pressure test.
16. Prime the fuel system. Verify the repair and check for fuel leaks. Refer to section "Priming the Fuel System".
17. If necessary, install the bumper end(s). Refer to the Original Equipment Manufacturer (OEM) procedures.
18. Close hood.
All information subject to change without notice.
05 04-18
Copyright © 2018 DETROIT DIESEL CORPORATION
17
- For best performance, follow the manufacturer's...
- Cleans, restores, protects the entire fuel system (fuel...
- Restores: lost power, acceleration, lost fuel economy, and...
- Reduces: rough idle, engine surge, hesitation, and spark...
- Improves: cold start performance, and fuel stability for up...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 0504-18
Replacement Service Bulletin Number:
MFR Communication Date: 2018-05-04
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: FUEL SYSTEM, GASOLINE
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
Autoauth, OE-
- 🔥 Historical lowest pr-ice now on sa-le--hot se-lling.
- 【🎈𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝟲 𝗲𝘀𝘀𝗲𝗻𝘁𝗶𝗮𝗹 𝗿𝗲𝘀𝗲𝘁 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗔𝗕𝗦 𝗕𝗹𝗲𝗲𝗱𝗶𝗻𝗴, 𝗢𝗶𝗹 𝗥𝗲𝘀𝗲𝘁, 𝗘𝗣𝗕, 𝗦𝗔𝗦, 𝗧𝗵𝗿𝗼𝘁𝘁𝗹𝗲 𝗥𝗲𝗹𝗲𝗮𝗿𝗻, 𝗮𝗻𝗱 𝗕𝗠𝗦—𝗽𝘂𝘁𝘁𝗶𝗻𝗴 𝗽𝗿𝗼𝗳𝗲𝘀𝘀𝗶𝗼𝗻𝗮𝗹-𝗴𝗿𝗮𝗱𝗲 𝗺𝗮𝗶𝗻𝘁𝗲𝗻𝗮𝗻𝗰𝗲 𝗯𝗮𝗰𝗸 𝗶𝗻 𝘆𝗼𝘂𝗿 𝗵𝗮𝗻𝗱𝘀.】Spongy brakes? Stuck oil light? Parking brake won't release? Off-center steering? Rough idle after battery disconnect? Draining battery? IF745 handles all with a few taps. One tool covers six dealer-level resets, saving hundreds in labor costs. ❗ NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨ 𝗜𝗙𝟳𝟰𝟱 𝗴𝗼𝗲𝘀 𝗯𝗲𝘆𝗼𝗻𝗱 𝗯𝗮𝘀𝗶𝗰 𝗰𝗼𝗱𝗲 𝗿𝗲𝗮𝗱𝗶𝗻𝗴 𝘄𝗶𝘁𝗵 𝟭𝟬 𝗶𝗻𝘁𝗲𝗴𝗿𝗮𝘁𝗲𝗱 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗗𝗧𝗖 𝗟𝗼𝗼𝗸𝘂𝗽, 𝗜/𝗠 𝗥𝗲𝗮𝗱𝗶𝗻𝗲𝘀𝘀, 𝗙𝗿𝗲𝗲𝘇𝗲 𝗙𝗿𝗮𝗺𝗲, 𝗟𝗶𝘃𝗲 𝗗𝗮𝘁𝗮, 𝗢𝟮𝗦, 𝗢𝗕𝗠, 𝗘𝗩𝗔𝗣, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Pulling a code tells you something is wrong. IF745 tells you what the code means, when the fault happened, and what data surrounds it. Pass emissions with one I/M Readiness tap. Freeze the fault moment with Freeze Frame. Monitor live sensor data in real time. Turn cryptic codes into clear answers.
- 【🛒 𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝗳𝘂𝗹𝗹-𝘀𝘆𝘀𝘁𝗲𝗺 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀 𝗮𝗰𝗿𝗼𝘀𝘀 𝗮𝗹𝗹 𝗺𝗼𝗱𝘂𝗹𝗲𝘀—𝗲𝗻𝗴𝗶𝗻𝗲, 𝗔𝗕𝗦, 𝗮𝗶𝗿𝗯𝗮𝗴, 𝘁𝗿𝗮𝗻𝘀𝗺𝗶𝘀𝘀𝗶𝗼𝗻, 𝘀𝘁𝗲𝗲𝗿𝗶𝗻𝗴, 𝘀𝘂𝘀𝗽𝗲𝗻𝘀𝗶𝗼𝗻, 𝗯𝗼𝗱𝘆 𝗲𝗹𝗲𝗰𝘁𝗿𝗼𝗻𝗶𝗰𝘀, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Warning lights on but you don't know why? Skip the $100+ diagnostic fee at the shop. Run a complete self-check from your driveway. IF745 reads and clears fault codes, retrieves ECU info, and displays live data from every accessible module—delivering a full vehicle health report in minutes, without leaving home.
- 【✅𝗜𝗙𝟳𝟰𝟱 𝗳𝗲𝗮𝘁𝘂𝗿𝗲𝘀 𝗮 𝟳-𝗶𝗻𝗰𝗵 𝗱𝗶𝘀𝗽𝗹𝗮𝘆, 𝗲𝗿𝗴𝗼𝗻𝗼𝗺𝗶𝗰 𝗱𝗲𝘀𝗶𝗴𝗻, 𝗪𝗶-𝗙𝗶 𝘂𝗽𝗱𝗮𝘁𝗲𝘀, 𝗮𝗻𝗱 𝘇𝗲𝗿𝗼 𝘀𝘂𝗯𝘀𝗰𝗿𝗶𝗽𝘁𝗶𝗼𝗻 𝗳𝗲𝗲𝘀 𝗳𝗼𝗿 𝗵𝗮𝘀𝘀𝗹𝗲-𝗳𝗿𝗲𝗲 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀.】Large screen means no squinting. Intuitive navigation and customizable data displays put key info at your fingertips. Wi-Fi delivers lifetime free updates without a computer. No recurring fees. No hidden costs. Just a reliable tool that works as hard as you do.
This product presentation was made with AAWP plugin.