Oshkosh: Load Span Tag Axles
SUBJECT: Axle Seat Inspection & Torque Value
Verification Procedure
LIT No: TB−H816
DATE: July 2018
REVISION: A
TABLE OF CONTENTS

Section 1

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Section 2

Affected LSTA Assemblies. . . . . . . . . . . . . . . 2

Section 3

Inspection/Rectification Process . . . . . . . . 3

LSTA — Axle Seat Inspection & Torque Value Verification Procedure
SECTION 1

Introduction
Hendrickson has learned that a limited number of Hendrickson Load Span Tag Axle ("LSTA") assemblies
equipped on certain Oshkosh S−Series front discharge mixers may have seat-to-axle fasteners that were
incorrectly torqued at the factory. The axle seats will continue to perform acceptably if this situation has
occurred, but to ensure the long-term durability of the axle and axle seat connections, Hendrickson is
providing these instructions for inspection and torquing of the axle seat fasteners. The affected LSTA
assemblies are equipped on Oshkosh S−Series mixers manufactured:
■■ Between September 1, 2017 and May 30, 2018, and
■■ Between March 25, 2008 and January 30, 2017 and subject to and/or retrofitted per Hendrickson

Technical Bulletin No. TB−H807, Rev. B.

NOTE

This rectification procedure should take approximately 10 minutes per vehicle.

SECTION 2

Affected LSTA Assemblies
IMPORTANT:

IF YOUR AXLE HAS A "75" MARK STAMPED ON THE TOP OF THE AXLE BEAM (SEE DRAWING−1 BELOW),YOUR
LSTA HAS BEEN PROPERLY TORQUED AT THE FACTORY AND IS NOT AFFECTED BY THE ISSUES COVERED BY
THIS HENDRICKSON TECHNICAL BULLETIN.

Drawing−1: Hendrickson Factory "75" Marks

75

To determine if your axle is affected by this Technical Bulletin, refer to Table−1 on Page 3. You will need one
of the following:
■■ Your Oshkosh Date of Manufacture (of the vehicle for which the LSTA was originally manufactured).

The Oshkosh date of manufacture can be found on the driver's door jamb (See Photo−2 on page 4).

■■ The Hendrickson Serial Number, which can be found on a tag on the axle beam as shown below in

Drawing−2:

Drawing−2: Hendrickson Serial Number

Table−1 (Page 3) contains information regarding Oshkosh dates of manufacture, axles subject to and/or
previously retrofitted per the prior Hendrickson Technical Bulletin TB−H807 Axle Weldment Replacement
Introduction

2

TB−H816

LSTA — Axle Seat Inspection & Torque Value Verification Procedure
Procedure for Oshkosh LSTA, Hendrickson part numbers, Oshkosh part numbers, and Hendrickson Serial
Numbers.
Table−1: LSTAs Affected by This Technical Bulletin:

IMPORTANT:

Oshkosh Vehicle Manufacture Date Range:

Hendrickson Part No.

Oshkosh Part No.

Hendrickson Serial Number
Range:

Vehicles manufactured
between 09/01/2017
and 05/30/2018

BAH13Z−XXK

4359153

HO1708280144 to
HO1804190073

Vehicles manufactured
between 03/25/08 and
01/30/2017 and subject
to and/or retrofitted per
Hendrickson Technical
Bulletin No. TB-H807,
Rev. B

BAH13Z−XXK

4359153

All serial numbers earlier than
HO1708280144 and subject to
Hendrickson Technical Bulletin
No.TB-H807, Rev. B

PLEASE INFORM HENDRICKSON IF YOUR FLEET SOLD ANY S WITH AFFECTED LSTA TO ANOTHER PARTY.
IN SUCH A CASE, PLEASE IDENTIFY THE NAMES AND CONTACT INFORMATION FOR ANY AND ALL SUCH
PARTIES.

SECTION 3

Inspection/Rectification Process
In order to determine the proper rectification procedure for your particular LSTA, you must follow these
procedures:
1. Chock the drive wheels of the vehicle.
2. Place the axle on the ground and turn off the truck (This should result in zero pressure being applied
to the LSTA assembly).
3. By hand, firmly hold the upper part of the fender mount as referenced in Photo−1 on the page 4.
Attempt to "rock" the LSTA back and forth. While rocking the axle, visibly inspect the axle seats for signs
of movement relative to the axle beam.
4. If there is no evidence of movement, re-torque the factory-installed axle seat nuts to 500−520 FT−LBS
using only a properly calibrated manual torque wrench; do not use an impact driver or other tool to
perform final torque of the nuts.
DO NOT OVER−TORQUE THE NUTS! MAKE SURE THAT EACH BOLT DOES NOT EXTEND MORE THAN .52"
(13.2 MM) BEYOND THE EDGE OF THE RESPECTIVE NUT (SEE DRAWING−3 BELOW). IF YOU HAVE OVERTORQUED THE FASTENER, YOU WILL HAVE TO CONTACT HENDRICKSON FOR ADDITIONAL FASTENERS.

Drawing−3: Torque Specifications for Axle Seat Fasteners

5. Provide the Oshkosh Vehicle Identification Number (VIN) and the axle's serial number and note "movement not apparent" to Hendrickson Technical Service. The VIN can be found on the driver−side door
jamb (See Photo−2 on page 4).
TB−H816

3

Inspection/Rectification Process

LSTA — Axle Seat Inspection & Torque Value Verification Procedure
6. If there is evidence of movement, re−torque according to Step 4 above. Next, please contact
Hendrickson Technical Services for information regarding the next steps of the rectification process:
phone: 800.660.2829 or e-mail: liftaxletech@hendrickson-intl.com.
Photo−1: LSTA Critical Locations

Photo−2: Location of Oshkosh Date of Manufacture

Inspection/Rectification Process

4

TB−H816

Load Span Tag Axles — Inspection & Torque Guide

www.hendrickson-intl.com

Specialty Products - Auxiliary Axle Systems
Hendrickson Canada
277 North High Street
250 Chrysler Drive, Unit #3
Hebron, OH 43025-8008 USA
Brampton, ON L6S 6B6 Canada
1.800.660.2829 (Toll-free U.S. and Canada)
905.789.1030
1.740.929.5600 (Outside U.S. and Canada)
Fax 905.789.1033
Fax 1.740.929.5601

TB−H816

Information contained in this literature was accurate at the time of publication. Product changes may have been made after the copyright date that are not reflected.
© 2018 Hendrickson USA, L.L.C. All Rights Reserved

Printed in United States of America