NHTSA ID Number: 10145110
Manufacturer Communication Number: FL762
TSB/Document Date: 2018-10-01
Summary
FL762 FCCC Motorhome Power Steering Hose Routing
Daimler Trucks
North America LLC
Recall Campaign
April 2018
FL762AB
NHTSA #18V-163
Transport Canada #2018-123
Subject: FCCC Motorhome Power Steering Hose Routing
Models Affected: Specific Freightliner Custom Chassis X-Line
chassis equipped with Cummins ISL engines and manufactured
January 21, 2010, through December 22, 2015.
General Information
Daimler Trucks North America LLC, on behalf of its wholly owned subsidiary, Freightliner Custom Chassis
Corporation, has decided that a defect that relates to motor vehicle safety exists on the vehicles mentioned
above.
There are approximately 10,234 vehicles involved in this campaign.
On certain motorhome chassis, the high pressure power steering hose may be routed with inadequate
clearance between the hose and a power stud on the starter motor. This may cause the hose to chafe against
the power stud on the starter, potentially leading to arcing and, in addition, may cause loss of fluid, short circuit,
and melting. Electrical arcing in the presence of leaking power steering fluid can increase the risk of a fire.
The high pressure power steering hoses will be rerouted to provide adequate clearance from the starter stud.
Additional Repairs
Dealers must complete all outstanding Recall and Field Service campaigns prior to the sale or delivery of a
vehicle. A Dealer will be liable for any progressive damage that results from its failure to complete campaigns
before sale or delivery of a vehicle.
Owners may be liable for any progressive damage that results from failure to complete campaigns within a
reasonable time after receiving notification.
Work Instructions
Please refer to the attached work instructions. Prior to performing the campaign, check the vehicle for a
completion sticker (Form WAR260).
Replacement Parts
Replacement parts are now available and can be obtained by ordering the part number(s) listed below from
your facing Parts Distribution Center.
If our records show your dealership has ordered any vehicles involved in campaign number FL762, a list of the
customers and vehicle identification numbers will be available in OWL. Please refer to this list when ordering
parts for this recall.
NOTE: Replacement of power steering hoses is per serial, please refer to PartsPro module 535/Steering
Plumbing for part numbers
Table 1 - Replacement Parts for FL762
Campaign Number
FL762AB
Part Description
Part Number
Qty.
RAIL CLIP
P-_CLIP
A 681 997 08 90
1 ea
1 ea
23-11357-016
23-10742-100
23-10900-025
23-13861-104
Per PartsPro/Module 535
BOLT
WASHER
NUT
POWER STEERING HOSE
Table 1
Page 1
1 ea
1 ea
1 ea
1 ea (as needed)
Daimler Trucks
North America LLC
Recall Campaign
April 2018
FL762AB
NHTSA #18V-163
Transport Canada #2018-123
Removed Parts
U.S. and Canadian Dealers, please follow Warranty Failed Parts Tracking shipping instructions for the
disposition of all removed parts. Export distributors, please destroy removed parts unless otherwise advised.
Labor Allowance
Table 2 - Labor Allowance
Procedure
Time Allowed
(hours)
SRT Code
Damage Code
Inspect power steering hose
0.5
996-0996A
06 - Inspect
Inspect and install P-clip
0.7
996-0996B
12 - Repair
Recall/Campaign
Inspect and replace power steering hose,
install P-clip (1% of vehicles are expected to
need the hose replaced.)
5.3
996-0996C
12 - Repair
Recall/Campaign
Campaign Number
FL762AB
Table 2
IMPORTANT: When the Recall has been completed, locate the base completion label in the appropriate location on the vehicle, and attach the red completion sticker provided in the recall kit (Form WAR260). If the vehicle does not have a base completion label, clean a spot on the appropriate location of the vehicle and first
attach the base completion label (Form WAR259). If a recall kit is not required or there is no completion sticker
in the kit, write the recall number on a blank sticker and attach it to the base completion label.
Claims for Credit
You will be reimbursed for your parts, labor, and handling (landed cost for Export Distributors) by submitting
your claim through the Warranty system within 30 days of completing this campaign. Please reference the
following information in OWL:
• Claim type is Recall Campaign.
• In the Campaign field, enter the campaign number and appropriate group (FL762A or FL762B).
• In the Primary Failed Part Number field, enter 25-FL762-000.
• In the Parts section, enter the appropriate part number(s) as shown in the Replacement Parts Table and
PartsPro, if replacement of the power steering hose is required. When replacing the power steering hose,
a maximum of 90.00 may be claimed for Dexron III power steering fluid and tie straps.
• In the Labor section, first enter the appropriate SRT from the Labor Allowance Table. Administrative time
will be included automatically as SRT 939-0010A for 0.4.
• The VMRS Component Code is 015-005-003 and the Cause Code is A1 - Campaign.
• U.S. and Canada -- Reimbursement for Prior Repairs. When a customer asks about reimbursement,
please do the following:
• Accept the documentation of the previous repair.
• Make a brief check of the customer’s paperwork to see if the repair may be eligible for reimbursement. (See the "Copy of Owner Letter" section of this bulletin for reimbursement guidelines for this
recall.)
• Submit an OWL Recall Pre-Approval Request for a decision.
• Attach the documentation to the pre-approval request.
• If approved, submit a based on claim for the pre-approval.
• Reimburse the customer the appropriate amount.
Page 2
Daimler Trucks
North America LLC
Recall Campaign
April 2018
FL762AB
NHTSA #18V-163
Transport Canada #2018-123
IMPORTANT: OWL must be viewed prior to performing the recall to ensure the vehicle is involved and the
campaign has not been previously completed. Also, check for a completion sticker prior to beginning work.
For questions, U.S. and Canadian dealers, contact the Warranty Campaigns Department from 7:00 a.m. to
4:00 p.m. Pacific Time, Monday through Friday, via Web inquiry at AccessFreightliner.com / Support / My Tickets
and Submit an Inquiry, or the Customer Assistance Center at (800) 385-4357, after normal business hours, if
you have any questions or need additional information. Export distributors, submit a Web inquiry or contact your
International Service Manager.
U.S.and Canadian Dealers: To return excess kit inventory related to this campaign, U.S. dealers must submit a
Parts Authorization Return (PAR) to the Memphis PDC. Canadian dealers must submit a PAR to their facing
PDC. All kits must be in resalable condition. PAR requests must include the original purchase invoice number.
Export Distributors: Excess inventory is not returnable.
The letter notifying U.S. and Canadian vehicle owners is included for your reference.
Please note that the National Traffic and Motor Vehicle Safety Act, as amended (Title 49, United States Code,
Chapter 301), requires the owner’s vehicle(s) be corrected within a reasonable time after parts are available to
you. The Act states that failure to repair a vehicle within 60 days after tender for repair shall be prima facie
evidence of an unreasonable time. However, circumstances of a particular situation may reduce the 60 day
period. Failure to repair a vehicle within a reasonable time can result in either the obligation to (a) replace the
vehicle with an identical or reasonably equivalent vehicle, without charge, or (b) refund the purchase price in
full, less a reasonable allowance for depreciation. The Act further prohibits dealers from selling a vehicle unless
all outstanding recalls are performed. Any lessor is required to send a copy of the recall notification to the
lessee within 10 days. Any subsequent stage manufacturer is required to forward this notice to its distributors
and retail outlets within five working days.
Page 3
Daimler Trucks
North America LLC
Recall Campaign
April 2018
FL762AB
NHTSA #18V-163
Transport Canada #2018-123
Copy of Notice to Owners
Subject: FCCC Motorhome Power Steering Hose Routing
For the Notice to U.S. Customers: This notice is sent to you in accordance with the National Traffic and Motor
Vehicle Safety Act. For the Notice to Canadian Customers: This notice is sent to you in accordance with the
Canadian Motor Vehicle Safety Act.
Daimler Trucks North America LLC, on behalf of its wholly owned subsidiary, Freightliner Custom Chassis
Corporation, has decided that a defect that relates to motor vehicle safety exists on specific Freightliner Custom
Chassis X-Line chassis equipped with Cummins ISL engines and manufactured January 21, 2010, through
December 22, 2015.
On certain motorhome chassis, the high pressure power steering hose may be routed with inadequate
clearance between the hose and a power stud on the starter motor. This may cause the hose to chafe against
the power stud on the starter, potentially leading to arcing and, in addition, may cause loss of fluid, short circuit,
and melting. Electrical arcing in the presence of leaking power steering fluid can increase the risk of a fire.
The high pressure power steering hoses will be rerouted to provide adequate clearance from the starter stud.
Please contact an authorized Daimler Trucks North America dealer to arrange to have the Recall performed and
to ensure that parts are available at the dealership. To locate an authorized dealer, search online at
www.Daimler-TrucksNorthAmerica.com. On the menu tab, select “Contact,” scroll down to “Find a Dealer,” and
select the appropriate brand. The Recall will take approximately one hour and will be performed at no charge to
you.
You may be liable for any progressive damage that results from your failure to complete the Recall within a
reasonable time after receiving notification.
If you do not own the vehicle that corresponds to the identification number(s) which appears on the Recall
Notification, please return the notification to the Warranty Campaigns Department with any information you can
furnish that will assist us in locating the present owner. If you have leased this vehicle, Federal law requires that
you forward this notice to the lessee within 10 days. If you are a subsequent stage manufacturer, Federal law
requires that you forward this notice to your distributors and retail outlets within five working days. If you have
paid to have this recall condition corrected prior to this notice, you may be eligible to receive reimbursement.
Please see the reverse side of this notice for details.
For the Notice to U.S. Customers: If you have questions about this Recall, please contact the Warranty
Campaigns Department at (800) 547-0712, 7:00 a.m. to 4:00 p.m. Pacific Time, Monday through Friday, e-mail
address [email protected], or the Customer Assistance Center at (800) 385-4357 after
normal business hours. If you are not able to have the defect remedied without charge and within a reasonable
time, you may wish to submit a complaint to the Administrator, National Highway Traffic Safety Administration,
1200 New Jersey Avenue, SE., Washington, DC 20590; or call the Vehicle Safety Hotline at (888) 327-4236
(TTY: 800-424-9153); or to http://www.safercar.gov. For the Notice to Canadian Customers: If you have
questions about this Recall, please contact the Warranty Campaigns Department at (800) 547-0712, 7:00 a.m.
to 4:00 p.m. Pacific Time, Monday through Friday, e-mail address [email protected], or
the Customer Assistance Center at (800) 385-4357 after normal business hours.
We regret any inconvenience this action may cause but feel certain you understand our interest in motor vehicle
safety.
WARRANTY CAMPAIGNS DEPARTMENT
Enclosure
Page 4
Daimler Trucks
North America LLC
Recall Campaign
April 2018
FL762AB
NHTSA #18V-163
Transport Canada #2018-123
Reimbursement to Customers for Repairs
Performed Prior to Recall
If you have already paid to have this recall condition corrected you may be eligible to receive reimbursement.
Requests for reimbursement may include parts and labor. Reimbursement may be limited to the amount the
repair would have cost if completed by an authorized Daimler Trucks North America LLC dealer. The following
documentation must be presented to your dealer for consideration for reimbursement.
Please provide original or clear copies of all receipts, invoices, and repair orders that show
• The name and address of the person who paid for the repair
• The Vehicle Identification Number (VIN) of the vehicle that was repaired
• What problem occurred, what repair was done, when the repair was done
• Who repaired the vehicle
• The total cost of the repair expense that is being claimed
• Proof of payment for the repair (such as the front and back of a cancelled check or a credit card receipt)
Reimbursement will be made by check from your Daimler Trucks North America LLC dealer.
Please speak with your Daimler Trucks North America LLC authorized dealer concerning this matter.
Page 5
Daimler Trucks
North America LLC
Recall Campaign
April 2018
FL762AB
NHTSA #18V-163
Transport Canada #2018-123
Work Instructions
Subject: FCCC Motorhome Power Steering Hose Routing
Models Affected: Specific Freightliner Custom Chassis X-Line
chassis equipped with Cummins ISL engines and manufactured
January 21, 2010, through December 22, 2015.
Power Steering Hose Inspection
1. Check the base label (Form WAR259) for a completion sticker for FL762 (Form WAR260) indicating this
work has been done. The base label is usually located on the front wall under the dash. If a sticker is present, no work is needed. If there is no sticker, proceed with the next step.
DANGER
When working on the vehicle, shut down the engine and set the parking brake. Before working under
the vehicle, always place jack stands under the frame rails to ensure the vehicle can not drop. Failure to
follow these steps could result in serious personal injury or death.
2. Park the vehicle on a level surface, shut down the engine, and set the parking brake.
3. Using jacks, raise the vehicle.
4. Place jack stands under the frame rails to ensure the vehicle can not drop.
5. Disconnect the battery cables, or if so equipped, turn the battery disconnect switch to the OFF position.
6. Locate the power steering hose (between the pump and the front of the vehicle) then follow the routing to
the starter stud area.
6.1
If the power steering hose is held with a P-clip near the starter stud, no work is needed. See Fig. 1.
Clean a spot on the base label (Form WAR259). Write the recall number, FL762, on a completion
sticker (Form WAR260), and attach it to the base label.
6.2
If the power steering hose is not held with a P-clip near the starter stud and shows no signs of chaffing, cuts, or holes, go to the Power Steering Hose Orientation procedure below.
6.3
If the power steering hose is not held with a P-clip near the starter stud and shows signs of chaffing,
cuts, or holes, go to the Power Steering Hose Replacement procedure on page 7. Less than 1% of
vehicles are expected to need the hose replaced.
Power Steering Hose Orientation
1. Install a rail clip on the top flange of the frame rail, just above the starter.
2. Using a P-clip, bolt, nut, and washer, secure the power steering hose on the rail clip. See Fig. 1. Tighten
the nut 72 lbf·in (813 N·cm).
3. For additional security, install tie bands around the hose to the harness near the frame rail within 18 inches
(46 cm) of the P-clip.
4. Clean a spot on the base label (Form WAR259). Write the recall number, FL762, on a completion sticker
(Form WAR260), and attach it to the base label.
Page 6
Daimler Trucks
North America LLC
Recall Campaign
April 2018
FL762AB
NHTSA #18V-163
Transport Canada #2018-123
1
2
11/11/2016
3
f462305
1. Rail Clip
2. P-clip
3. Power Steering Hose
Fig. 1, Power Steering Hose with P-Clip (body removed
for clarity)
Power Steering Hose Replacement
NOTE: Replacement of power steering hoses is per serial, please refer to PartsPro module 535/Steering
Plumbing for part numbers. Less than 1% of vehicles are expected to need the hose replaced.
1. Place a drain pan under the hydraulic pump.
2. At the hydraulic pump, loosen the high-pressure power steering line from the hydraulic pump and let the
fluid drain into the pan.
3. Place a drain pan under the power steering gear.
4. Depending on the vehicle model, loosen the high-pressure power steering line at the bottom of the steering
gear or at the bulkhead fitting, and let the fluid drain into the pan.
5. Remove the high-pressure power steering hose from the power steering pump.
6. At the front of the vehicle, use a male-to-male JIC fitting and attach a new high-pressure hose to the old
hose to pull the new hose through later.
7. Starting at the front of the vehicle, follow the high-pressure hose to the rear, removing all tie straps that secure the hose to the frame rail. Depending on the chassis model, it may be necessary to remove the Aqua
Hot reservoir and position it to the side in order to gain access to the rear compartment.
Page 7
Daimler Trucks
North America LLC
Recall Campaign
April 2018
FL762AB
NHTSA #18V-163
Transport Canada #2018-123
NOTICE
Do not use any power equipment to remove the hose. Doing so will damage the new hose. If there is
difficulty removing the hose, it may help to route the old hose toward the front of the vehicle over the
air bag.
NOTE: Two technicians are needed to pull the new hose through. Due to the angle of pull on the
hose, it is easier to remove the high-pressure hose from the back of the vehicle. Always pull the hose
in a straight line down the frame rail.
8. At the back of the vehicle, pull the old high-pressure hose through the frame rail until the new hose is in
position and can be attached to the power steering pump.
9. Attach the new high-pressure hose on the power steering pump, and at the steering gear or front bulkhead,
depending on the vehicle model. Tighten the fittings 42 lbf·ft (57 N·m). Ensure that all fittings and clamps
are tight.
10. Install a rail clip and P-clip to hold the power steering hose away from the starter stud. See Power Steering
Hose Orientation on page 6 for instructions, then continue with step 11 below.
11. Connect the battery cables, or if so equipped, turn the battery disconnect switch to the ON position.
IMPORTANT: In order to avoid overflowing the power steering reservoir, fill only to the FULL HOT
mark on the dipstick.
12. Fill the power steering reservoir with Dexron III fluid to the FULL HOT mark on the dipstick. Start the engine, then shut down the engine. Keep repeating the process until air is purged and the fluid level stops
dropping. Avoid running the power steering reservoir empty and foaming the fluid.
13. Once the fluid level stops dropping in the surge tank and the FULL COLD mark is maintained on the dipstick, start the engine and let it run. While the engine is running, slowly turn the steering wheel from full
right to full left, purging any air that is trapped in the steering system.
14. Check all fittings, ensuring there are no leaks.
15. Remove the jack stands.
16. Clean a spot on the base label (Form WAR259). Write the recall number, FL762, on a completion sticker
(Form WAR260), and attach it to the base label.
Page 8
- Advanced 6-Step Filtration Technology: Discover the...
- Certified Lead-Free: This camping water filter is...
- Access to Pure, Great-Tasting Water: Enjoy clean water...
- Patented Technology & Made in the USA: This in-line water...
- Versatile Applications: Easily attach this multi-purpose...
- 5 Setting Handheld RV Shower Head -High pressure handheld RV...
- Power Jet Mode -Simply take off the head and you can use the...
- Water Saving Pause Button -The water flow will be shut off...
- RV Shower Head Holder -2 Installations are available, screw...
- Easy Installation -The camper
shower head with hose, shower...
Last update on 2026-06-21 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: FL762
Replacement Service Bulletin Number:
MFR Communication Date: 2018-04-01
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: STEERING
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- Obd2 Bluetooth Scanner Lifetime Update: Ediag Elite offers revolutionary Advantage Lifetime Updates with unlimited access to the superior 15 reset service, bidirectional testing and full system diagnostics.The Ediag Elite is an excellent Bluetooth obd2 scanner diagnostic tool ideal for diy's and private car owners
- Bidirectional Control for Quickly Locating Problems: The Bidirectional Scan tool allows you to send commands directly from your smartphone to your vehicle for active testing. This feature helps to quickly narrow down problems such as air conditioning clutches, windows, doors, sunroofs, etc., reducing diagnostic time for mechanics and helping Diy users locate faults more easily. In addition, Ediag Elite provides fault analysis and repair guidance to help you solve problems efficiently.
- 15 Maintenance Resets: The current version introduces 15 popular special features: Oil Reset, Headlight Matching, Bleeding Reset, TPMS Reset, BMS Reset, Gear Box Relearn, Throttle Learning, Injector Coding, SAS Reset and more special functions in system diagnose menu. These functions make it easy for owners to carry out the necessary maintenance and servicing, ensuring that your vehicle stays in top condition, prolonging its service life and preventing common problems and breakdowns. Note: The Special function vary by model& year, Reach us check compatibility.
- Wide Compatibility CANFD & FCA Autoauth: Compatible with GM, Ford, Toyota, Chrysler, Honda, Mazda, Nissan, Mitsubishi, Hyundai, KIA with standard OBD2 port from 1996 to newer. More car brands and features will be released gradually. Newest Ediag Elite scanner supports CANFD Protocol and FCA cars. Note: Coverage may vary on different vehicle by model& year ,Please contact us to confirm compatibility before purchase.
- Perfect for Monitoring The Health of Your Vehicle: Ediag Elite is designed to make vehicle maintenance simple and efficient. With intelligent AutoVIN quick recognition, it is easy to connect to your car without the need for manual input. Real-time data is visualized in a variety of formats, including graphs, numeric, meter displays and clear 4-in-1 data charts, allowing you to effortlessly monitor real-time data. Data logging/reporting is available for playback and further analysis.
- No Annual Fees & 2026 Upgraded CAN FD: Why pay $199/year or more for updates? The 2026 newest Kingbolen K7 obd2 scanner features have been upgraded to Lifetime Updates without subscription fees, saving you significant costs in the long run. K7 scan tool also adds the CAN FD protocol for the latest GM models (2019+), enabling faster data transfer, reducing the risk of undetected errors
- 2026 Newest Top-tier Car Scanner: Kingbolen K7 diagnostic scan tool is equipped with most capabilities for daily repair/maintenance: Wireless diagnosis via Bluetooth, Bidirectional Test, ECU Online/Offline Code, 31+ Resets, PMI for Ford, Lincoln, Mazda, Global version for 100+ brand vehicles and 17 languages, no area limit, FCA AutoAuth
- OE-Level Full Systems Scan Tool: K7 professional diagnostic scanner with Auto Vin can do one-click to scan ECUs on most of vehicles, like pcm, ecm, eps, bcm, tpms, sas, a/c system... to read/clear code, view live data, freeze frame, read ecu info. 4-in-1 data stream graphics can make data viewing more intuitive. Detailed diagnostic reports will help you easily master the car situation as it can be shared by bluetooth or email! Adding workshop information can help your customers to know more
- Bidirectional Test/Active Test & ECU Code: Stop guessing and start fixing. Bidirectional scan tool Kingbolen K7 can perform real active test that can send commands to the vehicle's ECU to drive the actuators to work, like window, rear mirrors, sunroof, door, solenoids, wipers, headlamp, etc, helping you quickly find out bad parts and pinpoint faulty issues. K7 bidirectional scanner will be a good choice to save money and time on car repairs when performing complex maintenance and repair
- 31 Reset Functions: Avoid expensive dealership visits for simple services. Experience tells us that just a small repair service may cost a lot of money. Kingbolen K7 is a professional diagnostic scanner with 31 common maintenance services like Oil /SAS/EPB/TPMS Reset, Battery Matching, ABS Bleeding, Injector Code, etc. It effectively handles most of the car reset and relearning jobs, perfect for experienced DIYers and mechanics. Note: Functions in the menu vary across vehicles. Kindly check the compatibility before purchase
- WHY S608 STANDS OUT:2026 Kingbolen S608 is the only scanner <200 bucks that offers powerful active tests on Engine, ABS, SRS, and Transmission systems. Offers 9 resets,Covers 110+ global brands with a 6.2'' larger touchscreen
- KINGBOLEN'S NEW BIDIRECTIONAL SCAN TOOL: As the 2026 upgraded version of S600, our Newest S608 obd2 scanner has the powerful Bi-directional Control on Engine, ABS, SRS, and Transmission systems. It can send commands to the ECUs of actuators for functional tests and work status checks, such as ABS, fuel injectors, adjusting throttle, coolant pumps, EVAP test, fuel trim reset, etc. No more Guesswork. Quickly identify problem components without teardown, get fuss-free results in seconds.
- 【9 HOT RESET SERVICES CAR SCANNER】Tired of costly mechanic trips for common resets? The Kingbolen S608 obd2 scanner lets you do it yourself, even for beginners—quickly and effortlessly! It offers 9 hot reset functions: Oil/EPB Reset, ABS Bleeding, SAS Calibration, DPF Regeneration, Injector Coding, BMS Matching, Throttle Adaptation, Gear Learning. Stop paying mechanics for 5-minute jobs. Save hundreds per year! 🚗*Function vary from vehicle models. reach us to check compatibility firstly!
- 【4 SYSTEM DIAGNOSTIC TOOL + FULL OBDII FUNCTIONS】Kingbolen S608 is an OBDII scanner and 4 systems diagnostic tool made for home mechanics, DIYers, and professionals. You can access Engine, ABS, SRS, Transmission fault codes, track live data in graphs, and onboard DTC library lookup to find the right troubleshooting procedure, and diagnose with full 10 OBD2 test modes to fix most of emission issues. Give your aging cars routine maintenance to avoid costly repairs, a breakdown, or even a crash.
- 【NEW CAN FD, FCA/RENAULT SGW, 140+ BRANDS】Kingbolen S608 scanner for car supports 140+ vehicle brands, 100,000+ models, 28 languages and can be used worldwide. S608 stays up-to-date with modern vehicles, allows secure access to 2017+ FCA cars and 2015+ Renault cars (📢*Need to purchase an AutoAuth/Renault account by yourself), and supports the latest CAN-FD protocol for 2019+ GM/Chrysler, enabling 2X faster data transfer and more precise diagnostics. 🚗*Check compatibility before purchase.
Last update on 2026-06-21 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.