NHTSA ID Number: 10145097
Manufacturer Communication Number: 17730299RevB
TSB/Document Date: 2018-10-01
Summary
Operation Name: Hendrickson
Truck Commercial Vehical Systems Document Name: Technical Procedure - ULTIMAAX Rear Suspension for Fire and Rescue Vehicles - Service Instructions Summary: This document provides service instructions for Hendrickson ULTIMAAX rear suspension systems equipped on applicable fire and rescue vehicles.
ULTIMAAX® Rear Suspension
for Fire and Rescue Vehicles
SUBJECT: Service Instructions
LIT NO: 17730-299
DATE: July 2018
REVISION: B
TABLE OF CONTENTS
Section 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
Section 7
Alignment & Adjustments
Section 2
Product Description . . . . . . . . . . . . . . . . . 2
Drive Axle Pinion Angle . . . . . . . . . . . . . . . . 27
Section 3
Important Safety Notice. . . . . . . . . . . . . . 4
Drive Axle Alignment. . . . . . . . . . . . . . . . . . 27
Section 4
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 8
Axle Lateral Alignment. . . . . . . . . . . . . . . . . 29
Section 5
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 6
Preventive Maintenance
Bar Pin Alignment. . . . . . . . . . . . . . . . . . . . 29
Section 8
Component Replacement
Hendrickson Recommended
Inspection Intervals . . . . . . . . . . . . . . . . 13
Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Component Inspection . . . . . . . . . . . . . . . . 13
Center Bushings . . . . . . . . . . . . . . . . . . . . . 14
Shear Spring / Frame Hanger Assembly /
Saddle Assembly . . . . . . . . . . . . . . . . . . 33
Equalizing Beam End Connection. . . . . . . . 15
Progressive Load Spring (PLS). . . . . . . . . . . 38
Bar Pin End Bushings . . . . . . . . . . . . . . . . . 18
Equalizing Beam. . . . . . . . . . . . . . . . . . . . . 38
Bar Pin Shims. . . . . . . . . . . . . . . . . . . . . . . 18
Equalizing Beam Center Bushing. . . . . . . . . 41
Beam End Axle Brackets . . . . . . . . . . . . . . . 19
Equalizing Beam End Bushings. . . . . . . . . . 44
Frame Hanger Assembly . . . . . . . . . . . . . . . 20
Cross Tube. . . . . . . . . . . . . . . . . . . . . . . . . . 50
Shear springs . . . . . . . . . . . . . . . . . . . . . . . 20
Torque Rods . . . . . . . . . . . . . . . . . . . . . . . . 51
Progressive Load Springs (PLS). . . . . . . . . . 21
Torque Rod Bushings. . . . . . . . . . . . . . . . . . 52
Shock Absorber. . . . . . . . . . . . . . . . . . . . . . 32
Saddle Connection. . . . . . . . . . . . . . . . . . . 22
Section 9
Cross Tube. . . . . . . . . . . . . . . . . . . . . . . . . . 23
Section 10 Torque Specifications. . . . . . . . . . . . . . . 58
Torque Rods . . . . . . . . . . . . . . . . . . . . . . . . 24
Shock Absorbers. . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting Guide. . . . . . . . . . . . . . 57
ULTIMAAX® for Fire and Rescue Vehicles
SECTION 1
Introduction
This publication is intended to acquaint and assist maintenance personnel in the preventive
maintenance, service, and repair of the ULTIMAAX® Rear Rubber Suspension System for applicable
Fire and Rescue Vehicles.
NOTE
Use only
Hendrickson Genuine parts for servicing this suspension system.
It is important to read and understand the entire Technical Procedure publication prior to
performing any maintenance, service, or repair of this product. The information in this publication contains parts lists, safety information, product specifications, features, proper maintenance,
service, and repair instructions for ULTIMAAX suspensions.
Hendrickson reserves the right to make changes and improvements to its products and
publications at any time. Contact Hendrickson Tech Services for information on the latest version
of this manual at 1-866-755-5968 (toll-free U.S. and Canada), 1-630-910-2800 (outside U.S. and
Canada) or e-mail: techservices@hendrickson‑intl.com.
The latest revision of this publication is available online at www.hendrickson-intl.com.
SECTION 2
Product Description
ULTIMAAX is an advanced severe-duty rear rubber suspension designed specifically for fire and
rescue applications to balance outstanding durability, empty ride quality, loaded stability and
mobility. Through its unique design, the system offers premium ride quality in both empty and
loaded conditions, with increasing stability as the load increases.
■■ Equalizing beam — Formed and robotically welded to provide a narrow profile for weight
savings. Distributes load equally between axles to improve maneuverability, stability and
handling. Increases ground clearance with flat bottom design. Lowers the center of gravity to
increase stability.
■■ Saddle — Triangular geometry provides structure and durability. Weight efficient design
helps to increase payload, while offering a considerable weight savings versus competitive
suspensions.
■■ Frame hangers — Optimized design to balance durability and weight savings. Fabricated to
offer flexibility with multiple truck configurations.
■■ Rubber shear springs — Primary springs in unloaded condition, providing superb ride quality.
React to longitudinal loads during braking and accelerating for minimal displacement.
■■ Progressive load springs — Designed to balance empty ride quality and loaded stability.
Stiffness of progressive load spring increases as load increases, providing a unique balance
of empty ride quality and loaded stability.
■■ Longitudinal torque rods — Engineered to optimize resistance to axle wind-up during accel-
eration and braking.
■■ Transverse torque rods — Heavy‑duty transverse torque rods ensure maximum lateral axle
control and straight line suspension stability.
2
17730-299
ULTIMAAX® for Fire and Rescue Vehicles
FIGURE 2-1
54K • 58K Capacity
63K Capacity
9½" • 10" • 10¼" • 11½" Ride Height
10" • 10½" Ride Height
ULTIMAAX® SPECIFICATIONS
Suspension Rating
54K
58K
63K
54,000 lbs (24,494 kg)
58,000 lbs (26,308 kg)
63,000 lbs (28,576 kg)
Diagonal Articulation1
17½" (445 mm)
Ride Heights
9½"•10"•10¼"•11½" (241 mm, 254 mm, 260 mm, 292 mm)
10", 10½" (254 mm, 267 mm)
Axle Spacing2
54" (1,372 mm)
54", 56" (1,372 mm, 1,422, mm)
Hendrickson approves the use of ULTIMAAX in fire / rescue applications. All such applications must comply with applicable Hendrickson
specifications and must also be approved by the respective vehicle manufacturer with the vehicle in its original, as-built configuration.
Contact Hendrickson and the respective vehicle manufacturer for approval of additional applications.
1. Suspension articulation may exceed vehicle’s capability and may be limited by vehicle manufacturer; vehicle manufacturer installed axle
stops may restrict suspension’s articulation.
2. Contact Hendrickson for availability of additional beam lengths.
For additional details regarding specifications, applications, capacities, operating service and maintenance instructions, refer to applicable
Hendrickson technical literature (available at www.hendrickson-intl.com) or contact Hendrickson at 1-866-768-5968.
Actual product performance may vary depending upon vehicle configuration, operation, service and other factors.
U.S. and foreign patents granted and / or pending.
17730-299
3
ULTIMAAX® for Fire and Rescue Vehicles
SECTION 3
Important Safety Notice
Proper maintenance, service and repair are important to the reliable operation of the suspension.
The procedures recommended by Hendrickson and described in this technical publication are
methods of performing such maintenance, service and repair.
This technical publication should be read carefully to help prevent personal injury and to assure
that proper methods are used. Improper maintenance, service or repair may damage the vehicle,
cause personal injury, render the vehicle unsafe in operation, or void the manufacturer's warranty.
Failure to follow the safety precautions in this manual can result in personal injury and/or property
damage. Carefully read and understand all safety related information within this publication, on
all decals and in all such materials provided by the vehicle manufacturer before conducting any
maintenance, service or repair.
■■
EXPLANATION OF SIGNAL WORDS
Hazard “Signal Words” (Danger • Warning • Caution) appear in various locations throughout this
publication. Information accented by one of these signal words must be observed to help minimize the risk of personal injury to service personnel, or possibility of improper service methods
which may damage the vehicle or render it unsafe.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Additional Notes or Service Hints are utilized to emphasize areas of procedural importance and provide suggestions for ease of repair. The following definitions indicate the use of
these signal words as they appear throughout the publication.
INDICATES AN IMMINENTLY HAZARDOUS SITUATION, WHICH IF NOT AVOIDED, WILL RESULT IN SERIOUS
INJURY OR DEATH.
INDICATES A POTENTIAL HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, CAN RESULT IN SERIOUS
INJURY OR DEATH.
INDICATES A POTENTIAL HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, MAY RESULT IN MINOR OR
MODERATE INJURY.
NOTE
An operating procedure, practice condition, etc. which, is essential to emphasize.
SERVICE HINT
A helpful suggestion that will make the servicing being performed a little easier and/or faster.
Also note that particular service operations may require the use of special tools designed for specific
purposes.These special tools can be found in the “Special Tools” Section of this publication.
The torque symbol alerts you to tighten the fasteners to a specific torque value. See Torque
Specifications Section of this publication.
4
17730-299
ULTIMAAX® for Fire and Rescue Vehicles
■■
SAFETY PRECAUTIONS
FASTENERS
DISCARD USED FASTENERS. ALWAYS USE NEW FASTENERS TO COMPLETE A REPAIR. FAILURE TO DO
SO COULD RESULT IN FAILURE OF THE PART, OR MATING COMPONENTS, ADVERSE VEHICLE HANDLING,
PERSONAL INJURY, OR PROPERTY DAMAGE.
LOOSE OR OVER TORQUED FASTENERS CAN CAUSE COMPONENT DAMAGE, ADVERSE VEHICLE
HANDLING, PROPERTY DAMAGE, OR SEVERE PERSONAL INJURY. MAINTAIN CORRECT TORQUE VALUE
AT ALL TIMES. CHECK TORQUE VALUES ON A REGULAR BASIS AS SPECIFIED, USING A REGULARLY
CALIBRATED TORQUE WRENCH. TORQUE VALUES SPECIFIED IN THIS TECHNICAL PUBLICATION ARE FOR
HENDRICKSON SUPPLIED FASTENERS ONLY. IF NON-HENDRICKSON FASTENERS ARE USED, FOLLOW
TORQUE SPECIFICATION LISTED IN THE VEHICLE MANUFACTURER’S SERVICE MANUAL.
TORCH/WELDING
DO NOT USE A CUTTING TORCH TO REMOVE ANY FASTENERS OR BUSHINGS. THE USE OF HEAT
ON SUSPENSION COMPONENTS WILL ADVERSELY AFFECT THE STRENGTH OF THESE PARTS. A
COMPONENT DAMAGED IN THIS MANNER CAN RESULT IN THE ADVERSE VEHICLE HANDLING AND
POSSIBLE PERSONAL INJURY OR PROPERTY DAMAGE.
EXERCISE EXTREME CARE WHEN HANDLING OR PERFORMING MAINTENANCE IN THE AREA OF THE
EQUALIZING BEAM. DO NOT CONNECT ARC WELDING GROUND LINE TO THE EQUALIZING BEAM. DO
NOT STRIKE AN ARC WITH THE ELECTRODE ON THE EQUALIZING BEAM AND AXLE. DO NOT USE HEAT
NEAR THE EQUALIZING BEAM ASSEMBLY. DO NOT NICK OR GOUGE THE EQUALIZING BEAM. SUCH
IMPROPER ACTIONS CAN DAMAGE THE EQUALIZING BEAM ASSEMBLY AND CAUSE ADVERSE VEHICLE
HANDLING AND POSSIBLE PERSONAL INJURY OR PROPERTY DAMAGE.
LOAD CAPACITY
ADHERE TO THE PUBLISHED CAPACITY RATINGS FOR THE SUSPENSION. ADD-ON AXLE ATTACHMENTS
AND OTHER LOAD TRANSFERRING DEVICES CAN INCREASE THE SUSPENSION LOAD ABOVE ITS RATED
AND APPROVED CAPACITIES, WHICH CAN RESULT IN COMPONENT DAMAGE AND ADVERSE VEHICLE
HANDLING, POSSIBLY CAUSING PERSONAL INJURY OR PROPERTY DAMAGE.
MODIFYING COMPONENTS
DO NOT MODIFY OR REWORK PARTS WITHOUT AUTHORIZATION FROM HENDRICKSON. DO NOT
USE SUBSTITUTE OR REPLACEMENT COMPONENTS NOT AUTHORIZED BY HENDRICKSON. USE OF
MODIFIED, REWORKED, SUBSTITUTE OR REPLACEMENT PARTS NOT AUTHORIZED BY HENDRICKSON
MAY NOT MEET HENDRICKSON’S SPECIFICATIONS, AND CAN RESULT IN FAILURE OF THE PART,
ADVERSE VEHICLE HANDLING, AND POSSIBLE PERSONAL INJURY OR PROPERTY DAMAGE AND WILL
VOID WARRANTY. USE ONLY HENDRICKSON AUTHORIZED REPLACEMENT PARTS.
PERSONAL PROTECTIVE EQUIPMENT
ALWAYS WEAR PROPER EYE PROTECTION AND OTHER REQUIRED PERSONAL PROTECTIVE EQUIPMENT
TO HELP PREVENT PERSONAL INJURY WHEN PERFORMING VEHICLE MAINTENANCE, REPAIR OR
SERVICE.
PROCEDURES AND TOOLS
A TECHNICIAN USING A SERVICE PROCEDURE OR TOOL WHICH HAS NOT BEEN RECOMMENDED BY
HENDRICKSON MUST FIRST SATISFY HIMSELF THAT NEITHER HIS SAFETY NOR THE VEHICLE'S SAFETY
WILL BE JEOPARDIZED BY THE METHOD OR TOOL SELECTED. INDIVIDUALS DEVIATING IN ANY MANNER
FROM THE INSTRUCTIONS PROVIDED WILL ASSUME ALL RISKS OF CONSEQUENTIAL PERSONAL INJURY
OR DAMAGE TO EQUIPMENT INVOLVED.
17730-299
5
ULTIMAAX® for Fire and Rescue Vehicles
SUPPORT THE VEHICLE PRIOR TO SERVICING
PLACE THE VEHICLE ON A LEVEL FLOOR AND CHOCK THE WHEELS TO PREVENT THE VEHICLE FROM
MOVING OR ROLLING. DO NOT WORK AROUND OR UNDER A RAISED VEHICLE SUPPORTED BY ONLY
A FLOOR JACK OR OTHER LIFTING DEVICE. ALWAYS SUPPORT A RAISED VEHICLE WITH RIGID SAFETY
STANDS. FAILURE TO DO SO CAN CAUSE SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT.
IMPROPER JACKING METHOD
IMPROPER JACKING METHODS CAN CAUSE STRUCTURAL DAMAGE WHICH CAN CAUSE ADVERSE
VEHICLE HANDLING, PROPERTY DAMAGE OR SEVERE PERSONAL INJURY AND WILL VOID
HENDRICKSON’S WARRANTY.
■■ DO NOT USE THE SUSPENSION CROSS TUBE AS A JACKING POINT, SEE FIGURE 3-1, REFER TO
VEHICLE MANUFACTURER FOR PROPER JACKING INSTRUCTIONS.
■■ ACCEPTABLE LIFTING POINTS FOR A VEHICLE AT THE RATED LOAD INCLUDE BUT ARE NOT
LIMITED TO: THE AXLE, EQUALIZING BEAM, AND THE VEHICLE FRAME RAIL. REFER TO THE VEHICLE
MANUFACTURER FOR PROPER JACKING INSTRUCTIONS.
FIGURE 3-1
ULTIMAAX 63K Shown
Cross Tube
DO NOT grease or
use as a jacking point
Center Bushing
DO NOT grease
Equalizing
Beam
SADDLE CONNECTION
A SADDLE ASSEMBLY IS ATTACHED TO THE CENTER BUSHING OF EACH EQUALIZING BEAM WITH TWO
(2) SADDLE CAPS. EACH SADDLE CAP USES TWO (2) BOLTS TO CLAMP THE CENTER BUSHING INNER
METAL TO THE SADDLE. EACH SADDLE CAP MUST BE INSTALLED SO THAT THERE IS AN EVEN GAP
BETWEEN THE SADDLE CAP AND THE BASE OF THE SADDLE LEGS AS SHOWN IN FIGURE 3-2. IF EACH
SADDLE CAP IS NOT INSTALLED EVENLY, THE SADDLE LEGS COULD BECOME DEFORMED, RESULTING
IN BENT BOLTS OR DAMAGED SADDLES.
FIGURE 3-2
6
17730-299
ULTIMAAX® for Fire and Rescue Vehicles
TORQUE ROD ASSEMBLY
THE ULTIMAAX SUSPENSION INCORPORATES LONGITUDINAL AND TRANSVERSE TORQUE RODS FOR
VEHICLE STABILITY. IF THESE COMPONENTS ARE DISCONNECTED OR ARE NON-FUNCTIONAL THE
VEHICLE SHOULD NOT BE OPERATED. FAILURE TO DO SO CAN RESULT IN ADVERSE VEHICLE HANDLING
AND POSSIBLE TIRE CONTACT WITH THE FRAME OR THE SUSPENSION.
PARTS CLEANING
SOLVENT CLEANERS CAN BE FLAMMABLE, POISONOUS, AND CAUSE BURNS. TO HELP AVOID SERIOUS
PERSONAL INJURY, CAREFULLY FOLLOW THE MANUFACTURER’S PRODUCT INSTRUCTIONS AND
GUIDELINES AND THE FOLLOWING PROCEDURES:
1.
WEAR PROPER EYE PROTECTION.
2.
WEAR CLOTHING THAT PROTECTS YOUR SKIN.
3.
WORK IN A WELL-VENTILATED AREA.
4.
DO NOT USE GASOLINE OR SOLVENTS THAT CONTAIN GASOLINE. GASOLINE CAN EXPLODE.
5.
HOT SOLUTION TANKS OR ALKALINE SOLUTIONS MUST BE USED CORRECTLY. FOLLOW THE
MANUFACTURER’S RECOMMENDED INSTRUCTIONS AND GUIDELINES CAREFULLY TO HELP
PREVENT PERSONAL ACCIDENT OR INJURY.
DO NOT USE HOT SOLUTION TANKS OR WATER AND ALKALINE SOLUTIONS TO CLEAN GROUND OR
POLISHED PARTS. DOING SO WILL CAUSE DAMAGE TO THE PARTS AND VOID WARRANTY.
17730-299
7
ULTIMAAX® for Fire and Rescue Vehicles
SECTION 4
Special Tools
SADDLE TOOLS
DISASSEMBLY TOOL
ASSEMBLY TOOL
Hendrickson Part No. 66086-113L
Hendrickson Part No. 66086-108L
CENTER BUSHING TOOLS
RECEIVING TOOL
INSTALLATION TOOL
REMOVAL TOOL
Hendrickson Part No. 66086-112
Hendrickson Part No. 66086-107
Hendrickson Part No. 66086-110
BAR PIN STYLE END BUSHING TOOLS – 54K • 58K
RECEIVING TOOL
INSTALLATION TOOL
REMOVAL TOOL
Hendrickson Part No. 66086-111
Hendrickson Part No. 66086-106
Hendrickson Part No. 66086-109
ADAPTER STYLE END BUSHING TOOLS – 63K
End Bushing
Removal / Replacement Adapter
OTC Part Number 208350
Clamp
OTC Part Number 208349
Hendrickson Part No. 66086-101
OTC Part No. 1763
Visit otctools.com
Center Bushing
Removal / Replacement Adapter
OTC Part Number 28541
Not Needed for this publication
8
17730-299
ULTIMAAX® for Fire and Rescue Vehicles
TORQUE ROD BUSHING TOOLS
These shop made tools are made from cold rolled steel or equivalent. The drawings are for
reference only, Hendrickson does not supply these tools.
RECEIVING TOOL
INSTALLATION / REMOVAL TOOL
ULTRA ROD PLUS FUNNEL TOOL
Hendrickson Part No. 66086-000L
17730-299
9
ULTIMAAX® for Fire and Rescue Vehicles
SECTION 5
Parts List
■■ 54K
– Rosenbauer 9½" Ride Height • KME 10" Ride Height
– Seagrave 9½", 10¼" and 11½" Ride Height
■■ 63K – Rosenbauer 10½" Ride Height, KME 10" Ride Height
■■ 58K
10
17730-299
ULTIMAAX® for Fire and Rescue Vehicles
KEY NO. PART NO.
DESCRIPTION
VEHICLE
QTY.
Equalizing Beam Assembly with Shock Bracket 2
78489-540 54K - Rosenbauer, KME; 58K - Seagrave,
Includes Key Nos. 2-3
78634-540 63K - KME, Includes Key Nos. 2, 8
78634-560 63K - Rosenbauer, Includes Key Nos. 2, 8
Equalizing Beam Bushing Service Kits
• 54K / 58K Bar Pin Style
60961-755
Center and End Bushing, One Beam, Includes
Key No. 2-3,5-7, 21-23
60961-752
End Bushing, One Wheel End, Includes
Key Nos. 3-7
End Bushing Fasteners, Includes Key Nos. 5-7
56659-001 Tandem
56659-005 One Beam
34013-104 One Wheel End
• 63K Through Bolt Style
34013-052
End Bushing and Adapter Service Kit,
One Wheel End, Includes Key Nos. 8-9
2
Center Bushing
2
3
*Bar Pin End Bushing Assembly, 54K/58K,
Includes Key No. 4a
4
Bar Pin Shim
8
a
50130-000 0.19" / 0.19" Standard
b
50131-000 0.25" / 0.12" Optional
c
57026-000 0.375" Optional flat shim
5
*1"-8 UNC x 6" Bolt
8
6
*1" Hardened Washer
16
7
*1"-8 UNC Locknut
8
8
*End Bushing, 63K
4
9
21140-007
End Bushing Adapter Assembly, 63K
4
60961-759
Cross Tube Service Kit, Includes Key No. 10
and Weldable Loose Plug (Not Shown)
10
44642-008
Cross Tube - 1140 mm
1
11
Frame Hanger
2
• 34" Width - 54K/63K KME
78726-001 10" Ride Height
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 17730299RevB
Replacement Service Bulletin Number:
MFR Communication Date: 2018-07-01
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: SUSPENSION
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- 💯【Conta.ct us for Support Directly】If you met any issues about: Received a registered device/ Language Changing/ Function not Support/ VCI150 Blueto-oth connector malfunction/ Subscription Renewal, please conta.ct us via 📞autelsupply @outlook. com🛣️, we will provide perfect solution for you. ⚠️Note: Autel MK900BT comes with 1-Year Free Software Update, most features will remain active after update subscription expires. 1. For questions regarding updates or need more useful accessories, please conta.ct us via 📞autelsupply @outlook.com🛣️. 2. If the device fails to charge or turn on, please conta.ct us via 📞autelsupply @outlook. com🛣️, we will handle it promptly.
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW MODEL OF MK808S MK900 MX900 MK808BT MX808S】2026 newest Autel MK900BT retains all features of MK808S MX900 MX808S MK808Z MK808Z-BT MK808K-BT, while EXTRA added powerful functions (value 2000+ bucks). The Pro-level Autel MK900BT makes a big leaps: 28+➡40+, 50+➡3000+ Active Tests, 2026 NEW✅CAN FD & DOIP protocols ✅Pre&Post diagnostic report ✅WIFI Print ✅Auto VIN&Auto Scan 2.0 ✅Scan VIN/ License ✅Battery Test (Need purcha.se BT506). If found defect or us.ed, please conta-ct 📞autelsupply @outlook. com📞 get perf-ect solut.ion.
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS906 PRO】Differ from MS906BT MS906 MP808 MK808 MX808 MK808BT only 50 tests, Autel scanner MK900BT escaner automotriz professional offers 3000+ active tests, it can send command to ECUs & monitor actuators operation, quickly locating faulty components. Bidirectional scanning takes your diagnostics to the next level with menu lists 3000+ active tests, such as windows, rear mirrors, sunroof, wipers, fuel injector, coolant fans, radiator fan, AC clutch, coolant pump and more. Note: Functions are not available for all vehicles, please send vehicle VIN to us check compatibility.
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full level-up of OBD2 code reader MaxiCOM MK808S MK808 MK808Z MX808 MK808Z-BT with 28 service, Autel scan tool MK900BT/ MK900-BT offers 40+ maintenance service on 150+ brands 10,000 vehicles from 1996-2025-2026. Hottest Services like: Oil Reset, ABS Bleed, SAS Calibration, Injector Coding, SRS, Throttle Reset, Gearbox Reset, Battery Registration etc. Added 12+ advanced resets: rain slash light sensor reset, HVA.C/ SUS calibration etc. Welcome to send Vehicle Make>Model>Year>VIN>Functions you required to 📞autelsupply @ outlook . com📞 check compatibility.
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE/ AUTO VIN】2026 new release Autel MaxiCOM MK900-BT scan tool embodies all system diagnostic with its 8in display for all vehicles. Like Sna.p-on tools, it can perform ✔Read/Clear Codes✔Displays 5-in-1 Live Data✔Record & Playback Data✔Retrieve Info on all available systems like ABS ECM BCM SRS TCM etc. In addition to Auto VIN technology, Autel MK900BT adds Scan License/ Auto Scan 2.0 to identify vehicle’s VIN/ license, make, year, model, no need manual input; One-click WiFi Printing of Pre&Post comparison diagnostic reports, highlight root causes of problems.
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool supports Reading and Clearing DTCs, DTC Look Up, displaying Live Data, Freeze Frame & I/M Readiness, view vehicle information, etc., to figure out the root cause of the Check Engine Light (CEL) and turn it off, helping you catch any potential issues early and avoid excessive costs from unnecessary repairs.
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with 7 languages (English, French, Spanish, etc.) and various post-1996 OBD II protocol vehicles (Toyota
, Nissan, Honda, Ford, etc.), this OBD II scanner provides accurate and fast diagnosis for worldwide car owners. - 【FOR END USER & DIYERS】 This error code reader AL319 is “plug and play” and comes with an easy interface. Even if you’re not familiar with vehicle repair, you can quickly take control of this obd2 scanner, and get the information you want.
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check engine code reader features a patented One-Click I/M Readiness, TFT color display, built-in speaker, LED Indicator etc. The cable is long enough without being too long and getting in the way. No batteries are needed.
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the date of purchase and lifetime free update are offered by this Automobile OBDII scan tool. Welcome to contact us via Q&A, email, or hotline, and our after-sale-service team for technical support.
- 👨🎓Tips Before Order: 🚩All function are vehicle-specific - send VIN(17 digits)/Make/Model/Year & needed function via 📞auteldirect @ outlook . com📞 to check before order. 🚩Register tool: a) Follow on-screen guide; or b) Register em-ail on Autel we-b, then bind using SN(back of device) + verification code (find in tool settings or con-tact us via above em-ail). MK808BT PRO comes with ✅English, if need Spanish, please s.end device SN to add. ✅1-year war-ranty. ✅$150 worth 1yr fr-ee updates(New users: ignore renewal alerts). ⚠️📢Post-expiry: Most functions remain functional,for exclusions, refer to A+ Tips. ⚠️Fee for FCA AutoAuth Ga.teway(optional): $50/year, charged by AutoAuth,not Autel.
- 【2026 MK808BT PRO: Same as MK900BT, up of MK900 MX900 MK808S MX808S】Why pay more? 2026 MK808BT PRO functions as MK900BT and saves you 100USD. At same c0st, you now get diagnostic 8X faster and sup-port for 150+ models(1996-2026).💡Dramatically Improved: ✔️Faster & Smarter OS: Android 4.4➡ Android 11 ✔️More Services: 28+➡ 40+ ✔️Bidirectional Control: 50+➡ 3,000+ ✔️Enhanced Hardware: 1/32G➡ 4G/64G ✔️2.4GHz➡ 5G Dual WiFi ✔️Working range: 0.9m➡ 10m+ 🔋Battery test is clear on the large 7in display(BT506 required). 🔔Your Autel scanner is shipped brand new. For any issues(used, damaged, incompatible), e-m-a-il 📞auteldirect @ outlook . com📞 for priority resolution.
- 👍【New Next-Level Bidirectional Control, 50➡3000+ Tests, Covers Daily Repairs】Unlike the Autel DS708 DS808 MP808 MK808 and MX808 car diagnostic scanners, which offer only 50 functional tests, the Autel bidirectional scan tool MK808BT PRO is equipped with over 3000 active tests. These tests are widely used on car subsystems to help technicians quickly check if the car's actuators are functioning properly. Such as ABS, windows, rearview mirrors, wipers, sunroofs, fuel injectors, AC clutches, coolant fans, radiator fans, coolant pumps,etc. Tips📢: All functions are vehicle-specific, not universal to all vehicles,pls send VIN to 📞auteldirect @ outlook . com📞check compatibility before order.
- 👍【28+ Hot Services for 150+ Makes】Autel scan tool MK808BT PRO, upgraded with a BT VCI Mini(valued at 120USD), surpasses the old wired OBDII scanner MK808S MK900, by providing a convenient 33ft wireless working range, offering greater freedom and comfort compared to the 3.3ft cable limit of the MK900 MK808S MX808S car scanner. New features include VIN Check across different modules for comparison and 28+ resets, such as injector coding, ABS autobleed, Oil reset, SAS cali.bration, BMS, throttle relearn, suspension adjustments, etc. ⚠️📢Tips: Service functions are vehicle-specific, not universal to all vehicles, pls send VIN to 📞auteldirect @ outlook . com📞check compatibility before order.
- 👍【All Available Module Diagnosis - OE-Level Scanner】The OE versatile OBDII scan tool MK808BT PRO escaner para autos effectively works with all car systems: ABS, ECM, BCM, SRS, TCM,etc. It identifies vehicles via AutoVIN/manual input/select, like S.nap-on tools, it can ✔read/clear 7000+ DTCs, ✔read ECU info, ✔view 5-in-1 live data, ✔perform active tests, and ✔reset services. ✔Reports can be shared via QR-code and printed, working globally and 21+ multilingual. Supports 150+ US/EU/Asian makes, with ongoing updates from 2024 to 2026. ⚠️Note📢: The AutoVIN function usually works for post-2006 cars, depending on if the vehicle's VIN is stored in the ECU. You can always do manual input/select.
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.