NHTSA ID Number: 10144760
Manufacturer Communication Number: GCI-A0350-08
TSB/Document Date: 2018-09-17
Summary
GENERAL CONSUMER INFORMATION PERTAINING TO AN OWNER'S MANUAL
(Generator or Shore Power):
Plug the TV and DVD player into the outlet located above the inverter. Switch the inverter off (Switch is located beside the fan on the
back of the inverter opposite end as the plug outlet).. Use the same programing procedures as the 12 volt operation.
29
A) 400 watt inverter
B) Antenna booster
E) AC Power Source
Antenna Booster
A) Green indicator light
B) Booster Off/On switch.
C) 12 volt power source 3 amp
Inverter
On/Off switch
TV AC power cord
Vizio 22” LED TV
Full Digital TV
Soft Touch Buttons:
Source
Menu
Channel Up/Down
Volume Up/Down
.
.
TS Bed Assembly
Using the sofa switches beside the Thermostat on the driver side, lay the sofa down to a flat position. Place the bed support board
located behind the driver front seat on the maple support rails between the two ottoman benches. Place the ottoman back rest cushions
on the bed board between the ottoman seat cushions.
30
ASCENT FEATURES:
Dometic 3-way Refrigerator
Dometic .7 cu.ft. Microwave
2 Burner Flush Mount Cook Top with Glass Cover
Suburban 16,000 BTU Auto Ignition Furnace
Suburban 6 gal Auto Ignition Water Heater
Sure-Flo Demand Water System
Thetford Flush Toilet
Self Contained Bathroom with Shower & Sink
C.O. Detector
LP Gas detector
Smoke Detector
Fire Extinguisher
Fantastic Fan Roof Vent
Coach Battery
Battery Disconnect Switch
45 amp Power Converter with Distribution Panel
Monitor Panel System (Black, Gray, Fresh water, LP Gas & Battery)
Fresh Water Fill
Fresh Water Tank (80 L or 20.6 U.S. Gal)
Grey Water Tank ( 59 L or 15.6 U.S. Gal)
Black Water Tank (37.9 L or 10 U.S. Gal)
Generator Ready ( switch, wire for connections & mount brackets)
Exterior Shower
*Rear Bed Area ( 69” X 71”)
*Power Sofa
Awning Style Windows
Large Round Table
Porch Light
Cable TV Hook Up
TV Antenna
Water Heater By-Pass
Fiberglass Running Boards
Counter Top Flip Up
Exterior Plug
Sherwood Decorative Dash
Remote Propane Shut Off
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
NOTE: Pleasure-Way Ind. Ltd. reserves the right to make product changes at any time with out prior notice or obligation.
•
The bed area measurements may vary, due to components inside the vehicle.
31
Ascent Tire Carrier
1) Remove the Chrome Continental ring by releasing the key clip at the bottom of the
ring and spreading it to come off the tire.
2) Remove the plastic tire cover by pulling up from the bottom. Unplug the license light
by disconnecting the plugs.
3) Release the 15/16” safety bolt on the carrier arm locking pin. You will find a 15/16”
wrench in the tool pouch under the passenger front floor board.
32
4) Release and remove the safety pin, the locking clip and the carrier locking pin from the
tire arm.
5) Lower the tire to the horizontal position. Use the 15/16” wrench to release the tire from
the carrier arm.
(Caution: Tire and carrier arm is heavy use assistance if possible.)
6) Refer to your Dodge Sprinter Manual for jacking and tire replacement instructions.
7) Reverse the procedure to put the tire back into carried position.
Caution: The tire and carrier arm is heavy use assistance if possible for lifting and
replacing the locking pin into position.
Check list:
1) Continental cover is locked into place
2) License plate light is plugged in and working
3) Carrier arm locking bolt is tightened to locking pin
4) Safety pin and locking clip have been reinstalled
5) All tools, jack, wheel wrench, 15/16” wrench are stored in the passenger front floor
board area.
*Note: Repair or replace the damaged tire
33
Index / NHTSA homepage
TIRE SAFETY
Everything Rides On It
Studies of tire safety show that maintaining proper tire pressure, observing tire and vehicle load limits (not
carrying more weight in your vehicle than your tires or vehicle can safely handle), avoiding road hazards, and
inspecting tires for cuts, slashes, and other irregularities are the most important things you can do to avoid tire
failure, such as tread separation or blowout and flat tires. These actions, along with other care and maintenance
activities, can also:
•
Improve vehicle handling
•
Help protect you and others from avoidable breakdowns and accidents
•
Improve fuel economy
•
Increase the life of your tires.
This booklet presents a comprehensive overview of tire safety, including information on the following topics:
•
Basic tire maintenance
•
Uniform Tire Quality Grading System
•
Fundamental characteristics of tires
•
Tire safety tips.
Use this information to make tire safety a regular part of your vehicle maintenance routine. Recognize that the
time you spend is minimal compared with the inconvenience and safety consequences of a flat tire or other tire
failure.
Safety First–Basic Tire Maintenance
Properly maintained tires improve the steering, stopping, traction, and load-carrying capability of your vehicle.
Underinflated tires and overloaded vehicles are a major cause of tire failure. Therefore, as mentioned above, to
avoid flat tires and other types of tire failure, you should maintain proper tire pressure, observe tire and vehicle
load limits, avoid road hazards, and regularly inspect your tires.
Finding Your Vehicle's Recommended Tire Pressure and Load Limits
Tire information placards and vehicle certification labels contain information on tires and load limits. These
labels indicate the vehicle manufacturer's information including:
•
Recommended tire size
34
•
Recommended tire inflation pressure
•
Vehicle capacity weight (VCW–the maximum occupant and cargo weight a vehicle is designed to carry)
•
Front and rear gross axle weight ratings (GAWR– the maximum weight the axle systems are designed to
carry).
Both placards and certification labels are permanently attached to the vehicle door edge, door post, glove-box
door, or inside of the trunk lid. You can also find the recommended tire pressure and load limit for your vehicle
in the vehicle owner's manual.
Understanding Tire Pressure and Load Limits
Tire inflation pressure is the level of air in the tire that provides it with load-carrying capacity and affects the
overall performance of the vehicle. The tire inflation pressure is a number that indicates the amount of air
pressure– measured in pounds per square inch (psi)–a tire requires to be properly inflated. (You will also find
this number on the vehicle information placard expressed in kilopascals (kPa), which is the metric measure used
internationally.)
Manufacturers of passenger vehicles and light trucks determine this number based on the vehicle's design load
limit, that is, the greatest amount of weight a vehicle can safely carry and the vehicle's tire size.The proper tire
pressure for your vehicle is referred to as the "recommended cold inflation pressure." (As you will read below,
it is difficult to obtain the recommended tire pressure if your tires are not cold.)
Because tires are designed to be used on more than one type of vehicle, tire manufacturers list the "maximum
permissible inflation pressure" on the tire sidewall. This number is the greatest amount of air pressure that
should ever be put in the tire under normal driving conditions.
Checking Tire Pressure
It is important to check your vehicle's tire pressure at least once a month for the following reasons:
•
Most tires may naturally lose air over time.
•
Tires can lose air suddenly if you drive over a pothole or other object or if you strike the curb when
parking.
•
With radial tires, it is usually not possible to determine underinflation by visual inspection.
For convenience, purchase a tire pressure gauge to keep in your vehicle. Gauges can be purchased at tire
dealerships, auto supply stores, and other retail outlets.
35
The recommended tire inflation pressure that vehicle manufacturers provide reflects the proper psi when a tire is
cold. The term cold does not relate to the outside temperature. Rather, a cold tire is one that has not been driven
on for at least three hours. When you drive, your tires get warmer, causing the air pressure within them to
increase. Therefore, to get an accurate tire pressure reading, you must measure tire pressure when the tires are
cold or compensate for the extra pressure in warm tires.
Steps for Maintaining Proper Tire Pressure
•
Step 1: Locate the recommended tire pressure on the vehicle's tire information placard, certification
label, or in the owner's manual.
•
Step 2: Record the tire pressure of all tires.
•
Step 3: If the tire pressure is too high in any of the tires, slowly release air by gently pressing on the tire
valve stem with the edge of your tire gauge until you get to the correct pressure.
•
Step 4: If the tire pressure is too low, note the difference between the measured tire pressure and the
correct tire pressure. These "missing" pounds of pressure are what you will need to add.
•
Step 5: At a service station, add the missing pounds of air pressure to each tire that is underinflated.
•
Step 6: Check all the tires to make sure they have the same air pressure (except in cases in which the
front and rear tires are supposed to have different amounts of pressure).
If you have been driving your vehicle and think that a tire is underinflated, fill it to the recommended cold
inflation pressure indicated on your vehicle's tire information placard or certification label. While your tire may
still be slightly underinflated due to the extra pounds of pressure in the warm tire, it is safer to drive with air
pressure that is slightly lower than the vehicle manufacturer's recommended cold inflation pressure than to drive
with a significantly underinflated tire. Since this is a temporary fix, don't forget to recheck and adjust the tire's
pressure when you can obtain a cold reading.
Tire Size
To maintain tire safety, purchase new tires that are the same size as the vehicle's original tires or another size
recommended by the manufacturer. Look at the tire information placard, the owner's manual, or the sidewall of
the tire you are replacing to find this information. If you have any doubt about the correct size to choose,
consult with the tire dealer.
Tire Tread
The tire tread provides the gripping action and traction that prevent your vehicle from slipping or sliding,
especially when the road is wet or icy. In general, tires are not safe and should be replaced when the tread is
worn down to 1/16 of an inch. Tires have built-in treadwear indicators that let you know when it is time to
replace your tires. These indicators are raised sections spaced intermittently in the bottom of the tread grooves.
36
When they appear "even" with the outside of the tread, it is time to replace your tires. Another method for
checking tread depth is to place a penny in the tread with Lincoln's head upside down and facing you. If you can
see the top of Lincoln's head, you are ready for new tires.
Tire Balance and Wheel Alignment
To avoid vibration or shaking of the vehicle when a tire rotates, the tire must be properly balanced. This balance
is achieved by positioning weights on the wheel to counterbalance heavy spots on the wheel-and-tire assembly.
A wheel alignment adjusts the angles of the wheels so that they are positioned correctly relative to the vehicle's
frame. This adjustment maximizes the life of your tires and prevents your car from veering to the right or left
when driving on a straight, level road. These adjustments require special equipment and should be performed by
a qualified technician.
Tire Rotation
Rotating tires from front to back and from side to side can reduce irregular wear (for vehicles that have tires that
are all the same size). Look in your owner's manual for information on how frequently the tires on your vehicle
should be rotated and the best pattern for rotation.
A Tire Rotation Example
For maximum mileage, rotate your tires every 5,000 miles. Follow correct rotation patterns.
Tire Repair
The proper repair of a punctured tire requires a plug for the hole and a patch for the area inside the tire that
surrounds the puncture hole. Punctures through the tread can be repaired if they are not too large, but punctures
to the sidewall should not be repaired. Tires must be removed from the rim to be properly inspected before
being plugged and patched.
Uniform Tire Quality Grading System (UTQGS)
To help consumers compare a passenger car tire's treadwear rate, traction performance, and temperature
resistance, the federal government requires tire manufacturers to grade tires in these three areas. This grading
37
system, known as the Uniform Tire Quality Grading System, provides guidelines for making relative
comparisons when purchasing new tires. You also can use this information to inquire about the quality of tires
placed on new vehicles.
Although this rating system is very helpful when buying new tires, it is not a safety rating or guarantee of how
well a tire will perform or how long it will last. Other factors such as personal driving style, type of car, quality
of the roads, and tire maintenance habits have a significant influence on your tire's performance and longevity.
Treadwear grades are an indication of a tire's relative wear rate. The higher the treadwear number is, the longer
it should take for the tread to wear down. For example, a tire grade of 400 should wear twice as long as a tire
grade of 200.
Traction grades are an indication of a tire's ability to stop on wet pavement. A higher graded tire should allow
you to stop your car on wet roads in a shorter distance than a tire with a lower grade. Traction is graded from
highest to lowest as "AA", "A", "B", and "C".
Temperature grades are an indication of a tire's resistance to heat. Sustained high temperature (for example,
driving long distances in hot weather), can cause a tire to deteriorate, leading to blowouts and tread separation.
From highest to lowest, a tire's resistance to heat is graded as "A", "B", or "C".
Tire Fundamentals
Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This
information identifies and describes the fundamental characteristics of the tire and also provides a tire
identification number for safety standard certification and in case of a recall.
Information on Passenger Vehicle Tires
Please refer to the diagram below.
d
P
The "P" indicates the tire is for passenger vehicles.
38
Next number
This three-digit number gives the width in millimeters of the tire from sidewall edge to sidewall edge. In
general, the larger the number, the wider the tire.
Next number
This two-digit number, known as the aspect ratio, gives the tire's ratio of height to width. Numbers of 70 or
lower indicate a short sidewall for improved steering response and better overall handling on dry pavement.
R
The "R" stands for radial. Radial ply construction of tires has been the industry standard for the past 20 years.
Next number
This two-digit number is the wheel or rim diameter in inches. If you change your wheel size, you will have to
purchase new tires to match the new wheel diameter.
Next number
This two- or three-digit number is the tire's load index. It is a measurement of how much weight each tire can
support. You may find this information in your owner's manual. If not, contact a local tire dealer. Note: You
may not find this information on all tires because it is not required by law.
M+S
The "M+S" or "M/S" indicates that the tire has some mud and snow capability. Most radial tires have these
markings; hence, they have some mud and snow capability.
Speed Rating
The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time. The
ratings range from 99 miles per hour (mph) to 186 mph. These ratings are listed below. Note: You may not find
this information on all tires because it is not required by law.
Letter Rating
Speed Rating
Q
R
S
T
U
H
V
W
Y
99 mph
106 mph
112 mph
118 mph
124 mph
130 mph
149 mph
168* mph
186* mph
* For tires with a maximum speed capability over 149 mph, tire manufacturers sometimes use the letters ZR.
For those with a maximum speed capability over 186 mph, tire manufacturers always use the letters ZR.
U.S. DOT Tire Identification Number
This begins with the letters "DOT" and indicates that the tire meets all federal standards. The next two numbers
or letters are the plant code where it was manufactured, and the last four numbers represent the week and year
the tire was built. For example, the numbers 3197 means the 31st week of 1997. The other numbers are
marketing codes used at the manufacturer's discretion. This information is used to contact consumers if a tire
defect requires a recall.
Tire Ply Composition and Materials Used
The number of plies indicates the number of layers of rubber-coated fabric in the tire. In general, the greater the
39
number of plies, the more weight a tire can support. Tire manufacturers also must indicate the materials in the
tire, which include steel, nylon, polyester, and others.
Maximum Load Rating
This number indicates the maximum load in kilograms and pounds that can be carried by the tire.
Maximum Permissible Inflation Pressure
This number is the greatest amount of air pressure that should ever be put in the tire under normal driving
conditions.
UTQGS Information
Treadwear Number
This number indicates the tire's wear rate. The higher the treadwear number is, the longer it should take for the
tread to wear down. For example, a tire graded 400 should last twice as long as a tire graded 200.
Traction Letter
This letter indicates a tire's ability to stop on wet pavement. A higher graded tire should allow you to stop your
car on wet roads in a shorter distance than a tire with a lower grade. Traction is graded from highest to lowest as
"AA","A", "B", and "C".
Temperature Letter
This letter indicates a tire's resistance to heat. The temperature grade is for a tire that is inflated properly and not
overloaded. Excessive speed, underinflation or excessive loading, either separately or in combination, can cause
heat build-up and possible tire failure. From highest to lowest, a tire's resistance to heat is graded as "A", "B", or
"C".
Additional Information on Light Truck Tires
Please refer to diagram below.
d
Tires for light trucks have other markings besides those found on the sidewalls of passenger tires.
40
LT
The "LT" indicates the tire is for light trucks.
Max. Load Dual kg(lbs) at kPa(psi) Cold
This information indicates the maximum load and tire pressure when the tire is used as a dual, that is, when four
tires are put on each rear axle (a total of six or more tires on the vehicle).
Max. Load Single kg(lbs) at kPa(psi) Cold
This information indicates the maximum load and tire pressure when the tire is used as a single.
Load Range
This information identifies the tire's load-carrying capabilities and its inflation limits.
Snow Tires
In some heavy snow areas, local governments may require true snow tires, those with very deeply cut tread.
These tires should only be used in pairs or placed on all four wheels. Make sure you purchase snow tires that are
the same size and construction type as the other tires on your vehicle.
Index / NHTSA homepage
41
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: GCI-A0350-08
Replacement Service Bulletin Number:
MFR Communication Date: 2018-08-24
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- WHY CHOOSE THE 2025 CR MAX -Upgrade the latest diagnostic capabilities for all vehicles after 1996: upgrade to 49+maintenance services; 46 extra specific functions; real all systems/all control modules diagnose; over 40K+ bidirectional actuation tests for diagnosing all control moduels of cars; Powerful full OBD2 Functions; built-in ECU Coding for BMW
/ Audi/ VW/ RollsRoyce; Fr ee V.A.G Guide Function; Battery retistration for new battery adaptation and more. It covers all vehicle diagnostic services and some special professional vehicle maintenance servces, assists you to do home DIY vehicle maintenance or car repair as a pro technician. - NEWEST IN INNOVATION FULL OBD2 SERVICES- iCarsoft auto car diagnostic scanner compatible with CAN-FD, CR MAX can do it all-reads and clears trouble codes, ALL SYSTEM DIAGNOSIS such as engine, transmission, ABS and airbag etc. CR MAX code reader for all cars can perform I/M Readiness, Live Data, Freeze Frame, Vehicle Information, Monitor Test, On-Board Monitor, E vap System Test,O2 Sensor Test,DTC Library Lookup,etc. (Warm Tips: If you car is after 2023,please contact us for compatibility; 3. It comes with 16PIN OBD2 diagnostic adapter, please check your car diagnostic socket if it is 16pin socket, if your car is 14pin diagnostic socket please contact us for the solution.)
- 49 RESET+ 46 SERVICES- Performs: Oil Reset, EPB,SAS,Throttle, D-P - F, Battery, ABS, Injector, TPMS, Suspension, AC, Head Lamp, Body Stablity, Engine, Tramsmission, Airbag, Seat, Door-Win-Roof, Fuel Pump, Door, E-G- R.+21 NEWEST SERVICES( Need update scanner)-AdBlue, Clutch, Crankshaft, High Voltage Battery, Cruise Control, NO xSensor, Rain Sensor, Stop And Start, Turbocharger, Head Up Display, Radar Camera, Vehicle Setup, Cyliner Misfire Check,Speedlimitassist, ControlUnitReset,OxygenSensor, Seatbelt. Extra 46+ extra services based on car brand.(Tips: Quantity of reset/ calibration fucitons are based on car system that your vehicle model has)
- REVOLUTIONARY 40000+BIDIRECTIONAL ACTIVE TESTS: Upgraded CR Max scanner equip with numberous of actuational test items for covering all available vehicle control modules, no longer only do simple light test or window test like other scanners, performs hardware modules test and software control modules test for checking car units or new updated control moduels work well or not after maintenance/ repair/ re-installation/ control system updated (Example for Benz- Roller Sun Blind test; Backup Camera test ;Self-test; EPB test; Transport Mode test;Boost Pressure Positioner test; Fuel Pump test; AND MORE!!).(Warm tip: The available test items are based on control modules your car has)
- ECU CODING+ BATTERY REGISTRATION- Powerful ECU Coding service for BMW/MINI/RollsRoyce / Audi/VW/Seat/Skoda/Bentley/Bugatti/Lamborghini, Improves Engine Power Performance and Optimizes Fuel Efficiency and Match New Hardware Unit to car and Customized a comfortable Driving Modes and Fixes & Updates Original Software Bug. The battery test function for checking car battery health, perform battery reset (BMS ) for replacing a damaged or aging car battery with a new one and register new battery to car ECU
- 【Looking for More Professional Vehicle Scan Tool?】iCarsoft E660 2026 Upgrade Version OBD2 scan tool can do it all-reads and clears trouble codes on Engine system, ABS system, Transmission system and Airbag system, And with 6 reset function. It covers more than 59 vehicle makes from 1996-2023 models ( included most USA/ Asia / EU vehicle brand) with full OBDII. (As every car model has its-owned specific car system and ECUs, not all car models have full car ECUs which may prevent the scanner from performing all listed system diagnostics or reset services. Therefore, please email to us with car VIN and services required to do scanner's services for a compatibility check before purchasing.)
- 【OE-Level 4 Systems OBD2 Scanner】iCarsoft E660 2026 Upgrade Version diagnostic scanner offers comprehensive OBDII services, allowing you to quickly scan Engine system. It supports functions such as reading and erasing codes, checking I/M readiness, viewing freeze frame data, performing O2 sensor tests, conducting on-board monitoring, testing the evap system, auto VIN retrieval, and reading both generic and specific codes, as well as DTCs and battery tests.
- 【4 Systems Diagnosis for 10000+ Vehicles】 iCarsoft E660 2026 Upgrade Version adopts unique diagnostic software, works well for most Porsche, Benz, BMW, US Ford, Land Rover, Jaguar, Audi, VW, Volvo, Honda, Nissan, Infiniti, Toyota, Lexus, Scion, Isuzu, Hyundai, Kia, Daewoo, Mazda, Sprinter, Mini, Seat, Skoda, SAAB, EU Ford, Holden, AUS Ford, Acura, Subaru, Mitsubishi, Dacia, Renault, Fiat, GM, Chrysler, Citroen, Peugeot, Opel, Smart,Suzuki, Vauxhall, Alfa-Romeo, Lancia and etc.
- 【6 Reset Services】iCarsoft E660 2026 Upgrade Version is a diagnostic tool that offers professional maintenance services, including Oil Reset, EPB, BMS, ETC, SAS, TPMS Reset. It can help you easily reset oil change indicators, recalibrate steering angle sensors, relearn replaced electric parking brake and so on. For optimal vehicle performance and maintenance convenience. (Tips: Please update the softwareafter receiving the product to obtain new service functions)
- 【118+ Real Time Record & Live Graph View】iCarsoft E660 2026 Upgrade Version can automatically record vehicle text history and identify vehicle information. Preserve real-time data information. View & Graph Live Data. Support Data Review and Print. 15 languages: English, German, Dutch, Spanish, French and so on. We promise to offer Lifetime updates (Lifetime free Update via PC), and confidence in products. We also provide 1 year warranty + extra lifetime hardware free repair if you need it in the future. We prioritize user experience & strive to meet your expectations. Please do feel free to reach out to us if you have any question or problem about the usage.
- 【All-in-One Diagnostic Tool for Porsche + 2 Extra Vehicle Brands】New POR V4.0 is a professional car scanner specifically engineered with dedicated software pre-installed for Porsche. You can also download 2 additional software packages FOR FREE from 26 supported brands (e.g., for Benz, for BMW, for Audi, for Land Rover).Upgraded to adopt quad-core 1.3GHz processor and HD touchscreen and professional diagnsotic OS for faster& smooth diagnsotic.LIFETIME FREE UPDATES, NO SUBSCRIPTION COST! PLEASE TELL US YOUR CAR INFORMATION TO OBTAIN A LIST OF ALL COMPATIBLE SERVICES FOR YOUR CAR FIRST (FOR EXAMPLE: BATTERY REGISTRATION FUNCTION IS NOT COMPATIBLE WITH PORSCHE 997.2)
- 【29 MAINTENANCE SERVICES FOR PORSCHE SERIES CARS】 It can perform the 29 reset service for Porsche series cars-Oil Reset; SAS; EPB; BMS; ETC; DP ; ABS Bleeding; Injector Coding; TPMS; Air Suspension; Air Conditioner; Head Lamp; Body Stablity Control; Engine Control; Transmission; AirBag; Seat; DWR; MIS; EG; ODO; Clutch; High Voltage Battery; Cruise Control; Radar/Camera; Vehicle Setup,etc. Up to 49 vehicle-maintenance-services for the extra 2 vehicle brands you installed (Tip: Not all services will be worked on every car mode. Some vehicle models may be lack of certain ECU-control modules to make some services may not work).
- UPGRADE SERVICES: Breaks down 29 services to 234 sub-service for car owners/machinist to perform maintenance based on corresponding sub-modules! The detailed sub-service for sub-modules assist to perform precise vehicle maintenance.Improving the accuracy of car maintenance and reducing potential failure risks caused by whole-module maintenance to main modules.such as Oil Reset is refined into Reset maintenance interval/Reset service interval/Service Reset; Engine Control Reset is refined into Delete adaptation data/Short tests/System tests/Swirl-flap actuator/Bleeding high temperature coolant circuit and more.（sub-services vary based on vehicle model/year）
- 【EXTRA VEHICLE MAINTENANC SERVICES FOR SPECIFIC SYSTEMS】Have no ability to perferm calibration to special/specific systems/modules? This OBD2 scanner solve your troubles- for common systems/modules & for specific sytems/modules, assist you to perform diagnsing/calibration/reset/relearn services for non-common modules to finish your car maintenance/ diagnostic (eg: Central Computer system/module :Function activation/Multimedia interface test/AM Field Strength/Current FM Field Strength/FM Field Strength/MOST system reserve/Self-test/Deactivate Production Mode/Reset to factory settings/MOST System Test). (Tip: The services vary based on the vehicle brands)
- 【 MORE PROFESSIONAL BI-DIRECTIONAL ACTUATION TESET 】Exclusive POR V4.0 comes with powerful bidirectional testing capability,do actuaction test for deeper unit-checking after replacement or overhaul (1333 test items for Porsche, like:Fuel high-pressure fuel injector 1-4, Empty tank, Radiator fan, OTA-FC Connectivity, backrest, Backup battery, and more; 2136 test items for Audi; 1670 test items for Benz; 1599 test items for Volvo; 1360 test items for VW; 2705 test items for GM etc.). Help to check your car units work well or not after vehicle maintenance or daily car-body check, keep drives always in safety.(Warm tip:The quantity of test item is based on the units your car has)
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.