ACCOUNT TEAM COVERAGE
Please Deliver To: Service Managers and Warranty Decision Makers
FROM: Cummins Global Warranty Administration Communications
Subject: X15 CM2350 X114B and X116B Aftertreatment NOx sensor ATC for Volvo
Number: Atc2061
Expires:
Attention:

Date: 10-Aug-2018

01-Aug-2019 (U.S./Canada)
01-Aug-2019 (International)
michael.

@cummins.com

If additional information is required, please contact your Cummins Warranty Operations Group Leader.
DESCRIPTION:
This Campaign is being issued to address certain X15 CM2350 X114B and X116B units that have found fault code
3545 and 1887 active. This Campaign authorizes certified repair locations to use the attached procedures to
implement a drain hole in the NOx cup.
ACTION:
In order to qualify for repair under this field action, an engine:
1 will be covered Regardless of coverage status, and
2 must show as OPEN on QuickServe® Online for this field action.
NOTE: The ESN list is attached for reference.
After verifying that the engine meets the above requirements, perform the following actions:
1 Remove and replace the Outlet NOx Sensor. Please refer to Aftertreatment Outlet NOx Sensor replacement
Procedure 019-451 in Section 19, in the appropriate service manual.
2 Remove and replace the Particulate Sensor. Please refer to Aftertreatment Particulate Sensor Procedure
019-478 for the removal of the PM sensor in the appropriate service manual.
3 Please refer to Attachment B, Aftertreatment Outlet NOx Sensor Cup Cleaning Procedure. Complete all the
steps detailed in Attachment B.
4 Please refer to Attachment C, Aftertreatment Outlet NOx Sensor Cup Drain Hole Installation Procedure.
Complete all the steps detailed in Attachment C.
MATERIAL DISPOSITION:
There are no materials involved in the field action.
REIMBURSEMENTS:
Parts:
NOTE: Please contact ou
@cummins.com for any new order of Drill Bushing Kit and provide the mandatory
information below. Subject: Required Drill Bushing Kit. Requested Quantity: Address of Delivery: Contact Name:
Phone Number:
Parts are not covered under this field action:
Part Number
5395574

Quantity
1

Description
KIT,DRILL BUSHING (INFO ONLY)

NOTE: SRTs to gain access that are required to complete the repair, that are sufficiently explained in the claim
narrative, may also be claimed on this action.

Labor using applicable Access Code and Time:
SRT Code
Description
00-90X
Administrative time
19-0D4
Aftertreatment Particulate Sensor - Remove and Install - X15
CM2350 X114B (OPTIONAL)
19-0D5
Aftertreatment Outlet NOx Sensor - Remove and Install - X15
CM2350 X114B (OPTIONAL)
19-0G6
Aftertreatment Particulate Sensor - Remove and Install - X15
CM2350 X116B (OPTIONAL)
19-0G7
Aftertreatment Outlet NOx Sensor - Remove and Install - X15
CM2350 X116B (OPTIONAL)
99-902
BUSHING DRILLING AND CLEAN UP (QTY 5)

Time

Travel:
Travel is not covered under this field action. Towing is not covered under this field action.
Other Claimables:
Consumables are not covered under this field action.
Claim Instructions:
For Cummins Dealers, claims for this Field Campaign must be filed via RAPIDSERVE™ Web (rsw.cummins.com).
For information regarding RAPIDSERVE™ Web, please reference the "Warranty" tab in QuickServe® Online. If there
are additional questions, please contact your local Cummins Distributor.
Account Code: .............................................................................................................................................................. 27
Pay Code: .................................................................................................................................................. Distributor = X
Pay Code: ........................................................................................................................................................ Dealer = D
Pay Code: ................................................................................................................................................ International = I
Failure Code: ..................................................................................................................................................... WYNEBB
Attachments
atc2061_esn-list.xls atc2061_nox_cup_cleaning_instruction_attachmentb.pdfatc2061_nox_cup_drain_hole_installation_instruction_attachment-c.pdf

Service Instruction

Aftertreatment Outlet NOx Sensor Cup Clean Procedure.
Product
•
•

X15 CM2350 X114B
X15 CM2350 X116B

The purpose of this document is to guide the user through the steps involved in cleaning around the NOx
shield and cup in the SCR (Selective Catalyst Reduction).
Parts Required
The material required to clean the NOx cup are provided in Table 1. This is the only item approved for this
procedure.
Table (1.) Required Parts
Part Description
Distilled Water

Part Number

Personal Protection Equipment (PPE)
• Completing a Job Safety Assessment (JSA) prior to performing work helps identify job safety hazards
and prevent incidents.
• To reduce the possibility of personal injury, personal protective equipment (PPE) must be utilized.
Reference General Safety Instructions Procedure 204-006 in Section I of the corresponding Service
Manual.
Installation Tools
No special service tools are required to clean the NOx cup. The table below is the list of standard service tools
required along with any additional items recommended.
Table (1), Required Items
Service Tools
Clean Towels
Safety Glasses

Additional
Distilled water

WARNING
Wait for the Aftertreatment system to cool down before working on the hot exhaust or exhaust components.
Failure to do so could result in personal injury.

Preparation Steps:
1. Remove exhaust stack to expose the SCR outlet
according to the OEM service procedures.
2. Remove outlet sensors shown in Figure 1 and
place them in a safe place prior to cleaning the
NOx cup.
3. Refer to Aftertreatment Outlet NOx sensor
replacement procedure in section Procedure
019-451 in section 19, in the corresponding
service manual.
4. Refer to Aftertreatment Particulate Sensor
Procedure 019-478 for the removal of the PM
sensor in the corresponding service manual.

SCR Overview
Figure 1

Clean Nox Cup
5. Use prefer delivery method, dispense distilled
water into the NOx cup. Figure 2
ATTENTION: If a funnel is used, it MUST be clean and
clear of any contaminates. Failure to recognize this
can result in the introduction of new contaminates
that can and will cause the NOx sensor to fail.
6. Wait 30 seconds to allow contaminates to
dissolve.
7. Using shop air, insert the air chuck into sensor
boss to blowout the residuals until dry.
(Recommended shop air pressure: 90 to 150
psi.)
Caution: When using shop air, ensure PPE is used to
protect your eyes and skin in case any debris comes
loose during this process.

Distilled Water Delivery
Figure 2

8. Use a clean cloth to remove any debris found
outside the NOx cup and SCR outlet pipe.
9. Repeat steps 5 – 8 three (3) times to ensure all
contaminates are removed.
Caution: Do not use any chemical solvents or cleaners
to clean internal metal surface. Possible damage to
Aftertreatment SCR catalyst may occur.

Shop Air
Figure 3

Finishing Steps
10. Install the original Aftertreatment outlet NOx sensor and the PM sensor.

11. For the NOx sensor, see Aftertreatment Outlet NOx Sensor Procedure 019-451 in Section 19, in the
corresponding service manual

12. For the PM sensor, see Aftertreatment Particulate Sensor Procedure 019-478 in the corresponding Service
Manual.

Service Instruction

Aftertreatment Outlet NOx Sensor Cup Drain Hole Installation Procedure.
Product Affected
 X15 CM2350 X114B
 X15 CM2350 X116B
The purpose of this document is to guide the user through the steps involved in adding a drain hole inside the
NOx cup in the SCR (Selective Catalyst Reduction).
Parts Required
The material required to drill the NOx cup are provided in Table 1. This is the only item approved for this
procedure.
Table (1.) Required Parts
Part Description

Part Number

Special Tool Kit(Bushing, Drill bit)
Portable Drill
Special Tool Kit

as
Bus

Personal Protection Equipment (PPE)
 Completing a Job Safety Assessment (JSA) prior to performing work helps identify job safety hazards
and prevent incidents.
 To reduce the possibility of personal injury, personal protective equipment (PPE) must be utilized.
Reference General Safety Instructions Procedure 204-006 in Section I of the corresponding Service
Manual.

Installation Tools
Special service tools are required to drill the hole in the NOx cup. The table below is the list of standard service
tools required along with any additional items recommended.
Table (1), Safety Items
Shop Gloves
Clean Towels
Safety Glasses

Preparatory Steps
WARNING
Wait for the Aftertreatment system to cool down before working on the hot exhaust or exhaust components.
Failure to do so could result in personal injury.

1. Remove the NOx sensor and place it in a safe place prior
to drilling the hole and cleaning the NOx cup.
2. Refer to Aftertreatment Outlet NOx sensor replacement
procedure in section Procedure 019-451 in section 19, in
the corresponding service manual.
3. Refer to Aftertreatment Particulate Sensor Procedure
019-478 for the removal of the PM sensor in the
corresponding service manual.
4. Refer the attached Aftertreatment Outlet NOx Sensor
Cup Clean Procedure.

NOx Cup
Figure 1

5. Insert bushing into the NOx Cup as seen in Figure 2,
ensure the guide pins are located on the bottom.

6. Setup portable drill with the supplied drill bit.

7. Secure the bushing and insert the drill bit into the guide
hole.
Caution: Ensure your hands are free and clear from the rotating
parts and use precision to avoid breaking of drill bit.

8. Refer the attached Aftertreatment Outlet NOx Sensor
Cup Clean Procedure to remove any extra debris from
that accumulated during the drilling process.

Bushing inserted into NOx Cup
Figure 2

.

Finishing Steps
1. Install the original Aftertreatment outlet NOx sensor.

2. For the NOx sensor, see Aftertreatment Outlet NOx Sensor Procedure 019-451 in Section 19, in the
corresponding service manual