Customer Satisfaction Program
18197 Suspension Control Module Incorrect Calibration (US Only)
Reference Number:
Attention:

N182160760

Release Date:
Revision:

June 2018
00

This program is in effect until July 31, 2020.

Make
Chevrolet

Model
Corvette

Model Year
From
To
2017
2018

RPO
FE6

Description
Suspension System-Ride,
Handling, Performance, Var 1

Involved vehicles are marked “open” on the Investigate Vehicle History screen in GM Global Warranty Management
system. This site should always be checked to confirm vehicle involvement prior to beginning any required inspections
and/or repairs.
Condition

Correction

Certain 2017-2018 model year Chevrolet Corvette vehicles, equipped with (RPO FE6) suspension
system-ride, handling, and performance, may have an incorrect service calibration for the suspension
control module, which may not provide the softer, higher quality ride improvement as intended.
Dealer will reprogram the suspension control module.

Parts
No parts are required for this repair.
Warranty Information
Labor
Operation
9103847*
9103902**

Description
Electronic Suspension Control Module Reprogramming with SPS
Module Programming Not Required

Labor
Time
0.3
0.2

Trans.
Type
ZFAT
ZFAT

Net
Item
N/A
N/A

* To avoid warranty transaction rejections, the SPS Warranty Claim Code must be entered when submitting this
transaction. Note that if multiple modules are reprogrammed, all claim codes must be entered with a comma separating
each code.
** SPS Warranty Claim Code is NOT required when submitting this transaction.
Service Procedure
Note: Carefully read and follow the instructions below.

•

Ensure the programming tool is equipped with the latest software and is securely connected to the data link
connector. If there is an interruption during programming, programming failure or control module damage may
occur.

•

Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will
interrupt programming. When required install the PSC-550 or EL49642 SPS Programming Support Tool to
maintain system voltage. If not available, connect a fully charged 12 V jumper or booster pack disconnected from
the AC voltage supply. DO NOT connect a battery charger.

•

Turn OFF or disable systems that may put a load on the vehicles battery such as; interior lights, exterior lights
(including daytime running lights), HVAC, radio, etc.

•

Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M)
system status indicators to NO.

•

If the Same Calibration/Software Warning is noted on the SPS Controller screen, do NOT attempt to program
the module. No further action is required. Refer to the Warranty section of the bulletin and use labor operation
code 9103902, Module Programming Not Required.

1.

Reprogram the electronic suspension control module. Refer to K19 Suspension Control Module: Programming and
Setup in SI.

2.

Record SPS Warranty Claim Code on job card for warranty transaction submission.

Dealer Responsibility
All new, used, GM Certified Used, courtesy transportation vehicles, dealer shuttle vehicles, etc. in dealers' possession
and subject to this program must be held and inspected/repaired per the service procedure of this bulletin before

Copyright 2018 General Motors. All Rights Reserved.

Page 1 of 3

Customer Satisfaction Program
18197 Suspension Control Module Incorrect Calibration (US Only)
customers take possession of these vehicles. Involved vehicles must be held and not delivered to customers, dealertraded, released to auction, used for demonstration, or any other purpose.
All GM Certified Used vehicles currently in the dealers’ inventory within the Certified Pre-Owned Inventory System
(CPOIS) will be de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting
an accepted/paid warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified
for sale within the CPOIS system, or once again be used in the CTP program.
Dealers are to service all vehicles subject to this program at no charge to customers, regardless of mileage, age of vehicle,
or ownership, through July 31, 2020. Customers who have recently purchased vehicles sold from your vehicle inventory,
and for which there is no customer information indicated on the involved vehicle listing, are to be contacted by the dealer.
Arrangements are to be made to make the required correction according to the instructions contained in this bulletin. A
copy of the customer letter is provided in this bulletin for your use in contacting customers. Program follow-up cards
should not be used for this purpose, since the customer may not as yet have received the notification letter.
In July 31, 2020, you must take the steps necessary to be sure the program correction has been made before selling or
releasing the vehicle.
Courtesy Transportation – For USA
Courtesy transportation is available for customers whose vehicles are involved in a product program and still within the
warranty coverage period. See General Motors Service Policies and Procedures Manual, Sections 1.4 and 6.1.10, for
courtesy transportation program details.
Dealer Reports
For dealers with involved vehicles, a listing with involved vehicles has been prepared and will be provided to U.S. and
Canadian dealers through the GM GlobalConnect Recall Reports, or sent directly to export dealers. The listing may
contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor
vehicle registration data for any purpose other than follow-up necessary to complete this program is a violation of law in
several states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to
complete this program.
Customer Notification
USA - General Motors will notify customers of this program on their vehicle (see copy of customer letter included with this
bulletin).

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of
conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained
technicians have the tools, equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT
assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your
vehicle may benefit from the information.

We Support
Voluntary Technician
Certification

July 2018
Page 2 of 3

Customer Satisfaction Program
18197 Suspension Control Module Incorrect Calibration (US Only)
This notice applies to your vehicle, VIN: ________________________________
Dear General Motors Customer:
We have learned that your 2017-2018 model year Chevrolet Corvette vehicle equipped with suspension system-side,
handling, and performance, may have an incorrect service calibration for the suspension control module, which may not
provide the softer, higher quality ride improvement as intended.
Your satisfaction with your Chevrolet Corvette is very important to us, so we are announcing a program to fix this
condition.
What We Will Do: Your GM dealer will reprogram the suspension control module. This service will be performed for
you at no charge until July 31, 2020.
What You Should Do: To limit any possible inconvenience, we recommend that you contact your dealer as soon as
possible to schedule an appointment for this repair.
If you have any questions or concerns that your dealer is unable to resolve, please contact the appropriate Customer
Assistance Center at the number listed below.
Division
Chevrolet
Puerto Rico – English
Puerto Rico – Español
Virgin Islands

Number
1-800-222-1020
1-800-496-9992
1-800-496-9993
1-800-496-9994

Text Telephones (TTY)
1-800-833-2438

We sincerely regret any inconvenience or concern that this situation may cause you. We want you to know that we will
do our best, throughout your ownership experience, to ensure that your Corvette vehicle provides you many miles of
enjoyable driving.
Neelie O’Connor
Executive Director
North America Contact Center Operations
18197

Page 3 of 3

GLOBAL SAFETY FIELD INVESTIGATIONS
DCS4787
URGENT - DISTRIBUTE IMMEDIATELY
Date:

June 21, 2018

Subject: 18197 - Customer Satisfaction Program
Suspension Control Module Incorrect Calibration (US Only)
Models: 2017-2018 Chevrolet Corvette
Equipped with Suspension System-Ride, Handling, Performance (FE6)
To:

All General Motors Dealers

General Motors is releasing Customer Satisfaction Program 18197 today. The
total number of U.S. vehicles involved is approximately 26. Please see the
attached bulletin for details.
Customer Letter Mailing
The customer letter mailing will begin on July 5, 2018.
Global Warranty Management (GWM)
The Investigate Vehicle History (IVH) screen in the GWM system will be updated June
21, 2018. A list of involved vehicles in dealer new inventory is attached to this
message. Please hold all warranty transactions until IVH has been updated.
END OF MESSAGE
GLOBAL SAFETY FIELD INVESTIGATIONS