NHTSA ID Number: 10143415
Manufacturer Communication Number: 17089 01
TSB/Document Date: 2018-08-06
Summary
17089-01 - Product Emissions Recall. Revised. This bulletin has been revised to add the requirement for an SPS warranty claim code to accompany warranty transaction submission, and to add notes to the service procedure. Please discard all copies of bulletin 17089. General Motors
has decided to conduct a Voluntary Emission Recall certain vehicles equipped with a 2.0L (RPO LUZ) diesel engine. On some vehicles, depending on driving habits, soot may build up on the engine?s NOx position 1 sensor and / or oxygen sensor, causing the vehicle Check Engine Indicator to illuminate. An earlier correction for this condition (Voluntary Emission Recall 15594) may, under certain driving conditions, inadvertently cause the vehicle Check Engine Indicator to illuminate.For vehicles that were not serviced under previous recall 15594, dealers are to replace the NOx position 1 sensor and reprogram the engine control module with a modified calibration, and initiate a Diesel Particulate Filter cleaning cycle. For vehicles previously serviced under recall 15594, dealers are to reprogram the engine control module with a modified calibration, and initiate a Diesel Particulate Filter cleaning cycle. Confirm status of recall 15594 following the instructions in the Warranty Information section.
Product Emission Recall
17089 NOx Position 1 Sensor Replacement
Reference Number:
Revision Description:
N151645630
Release Date: May 2018
Revision: 01
This bulletin has been revised to add the requirement for an SPS warranty claim code to
accompany warranty transaction submission, and to add notes to the service procedure.
Please discard all copies of bulletin 17089.
Attention: The vehicle population involved in discontinued Voluntary Emission Recall 15594 has now been
transferred to recall 17089. Customers are being instructed to return their vehicles for repair regardless of
whether recall 15594 was performed previously.
Make
Chevrolet
Model
Cruze
Model Year
From
To
2014
2015
RPO
LUZ
Description
2.0L Diesel Engine
Involved vehicles are marked “open” on the Investigate Vehicle History screen in GM Global Warranty Management
system. This site should always be checked to confirm vehicle involvement prior to beginning any required inspections
and/or repairs.
Condition
Correction
General Motors has decided to conduct a Voluntary Emission Recall involving certain 2014 and 2015
model year Chevrolet Cruze model vehicles equipped with a 2.0L (RPO LUZ) diesel engine. On some
vehicles, depending on driving habits, soot may build up on the engine’s NOx position 1 sensor and / or
oxygen sensor, causing the vehicle Check Engine Indicator to illuminate.
An earlier correction for this condition (Voluntary Emission Recall 15594) may, under certain driving
conditions, inadvertently cause the vehicle Check Engine Indicator to illuminate.
For vehicles that were not serviced under previous recall 15594, dealers are to replace the NOx position
1 sensor and reprogram the engine control module with a modified calibration, and initiate a Diesel
Particulate Filter cleaning cycle
For vehicles previously serviced under recall 15594, dealers are to reprogram the engine control module
with a modified calibration, and initiate a Diesel Particulate Filter cleaning cycle.
Confirm status of recall 15594 following the instructions in the Warranty Information section.
Parts
Quantity
1
Part Name
Part No.
12662658
NOx Sensor (Position 1)
Warranty Information
Due to the discontinuation of recall 15594, all vehicles involved in recall 15594 will appear as “closed” on the Global
Warranty Summary page. In order to confirm if recall 15594 was completed please click View Vehicle Transaction
History. The individual transaction card for recall 15594 will indicate, “9101952-N150594 - Nitrogen Oxides Sensor
Replacement - Position 1 and Engine Control Module Reprogramming” if the vehicle was previously repaired.
Labor
Operation
9103087**
9103088**
Description
Recall 15594 Not Performed: Nitrogen Oxides Sensor
Replacement - Position 1, DPF Regen Enable, Engine Control
Module Reprogramming with SPS
Recall 15594 Previously Performed: Engine Control Module
Reprogramming with SPS
Labor
Time
1.5
Trans.
Type
ZFAT
Net
Item
N/A
1.1*
ZFAT
N/A
*Time includes DPF Service Regeneration procedure, fuel trim reset, NOx sensor reset, and resetting the Engine Oil Life.
** To avoid warranty transaction rejections, the SPS Warranty Claim Code must be entered when submitting this
transaction. Note that if multiple modules are reprogrammed, all claim codes must be entered with a comma separating
each code.
Copyright 2016 General Motors. All Rights Reserved.
Page 1 of 7
Product Emission Recall
17089 NOx Position 1 Sensor Replacement
Warranty Claim Code Information Retrieval
If the SPS Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS system as
follows:
-
Open TIS on the computer used to program the vehicle
-
Select and start SPS
-
Select Settings
-
Select the Warranty Claim Code tab
The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is
retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code
field.
Service Procedure
Determine if recall 15594 has been completed on this vehicle. Refer to Warranty Information section above.
Recall 15594 Not Performed on Vehicle
1.
Remove the Nitrogen Oxides (NOx) sensor. Refer to Nitrogen Oxides Sensor Replacement - Position 1 in SI.
2.
Install a new NOx sensor. Refer to Nitrogen Oxides Sensor Replacement - Position 1 in SI.
Note: Carefully read and follow the instructions below.
•
Ensure the programming tool is equipped with the latest software and is securely connected to the data link
connector. If there is an interruption during programming, programming failure or control module damage may
occur.
•
Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will
interrupt programming. When required install the EL-49642 SPS Programming Support Tool to maintain system
voltage. If not available, connect a fully charged 12 V jumper or booster pack disconnected from the AC voltage
supply. DO NOT connect a battery charger.
•
Turn OFF or disable systems that may put a load on the vehicles battery such as; interior lights, exterior lights
(including daytime running lights), HVAC, radio, etc.
•
Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M)
system status indicators to NO.
5045242
Note: If the Same Calibration/Software Warning is noted on the SPS controller screen, select “OK” and continue
programming.
Page 2 of 7
Product Emission Recall
17089 NOx Position 1 Sensor Replacement
3.
Reprogram the K20 Engine Control Module. Refer to K20 Engine Control Module: Programming and Setup (LUZ)
in SI.
Warning: Tailpipe outlet exhaust temperature will be greater than 300°C (572°F) during this procedure. To help prevent
personal injury or property damage from fire or burns, perform the following:
•
Do NOT connect any shop exhaust removal hoses to the vehicle tailpipe.
•
Park the vehicle outdoors and keep people, other vehicles, and combustible material away during this procedure.
•
Do NOT leave the vehicle unattended.
4.
Perform the Diesel Particulate Filter (DPF) Service Regeneration Enable procedure with a scan tool. Refer to Diesel
Particulate Filter DPF Regeneration Enable in SI.
5.
Perform a fuel trim reset with a scan tool.
6.
With a scan tool, reset the Engine Oil Life Remaining back to the original percentage recorded before the control
module was replaced, if available.
15594 Previously Performed on Vehicle
Note: Carefully read and follow the instructions below.
•
Ensure the programming tool is equipped with the latest software and is securely connected to the data link
connector. If there is an interruption during programming, programming failure or control module damage may
occur.
•
Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will
interrupt programming. When required install the EL-49642 SPS Programming Support Tool to maintain system
voltage. If not available, connect a fully charged 12 V jumper or booster pack disconnected from the AC voltage
supply. DO NOT connect a battery charger.
•
Turn OFF or disable systems that may put a load on the vehicles battery such as; interior lights, exterior lights
(including daytime running lights), HVAC, radio, etc.
•
Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M)
system status indicators to NO.
5045242
Note: If the Same Calibration/Software Warning is noted on the SPS controller screen, select “OK” and continue
programming.
1.
Reprogram the K20 Engine Control Module. Refer to K20 Engine Control Module: Programming and Setup (LUZ) in
SI.
Page 3 of 7
Product Emission Recall
17089 NOx Position 1 Sensor Replacement
Warning: Tailpipe outlet exhaust temperature will be greater than 300°C (572°F) during this procedure. To help prevent
personal injury or property damage from fire or burns, perform the following:
•
Do NOT connect any shop exhaust removal hoses to the vehicle tailpipe.
•
Park the vehicle outdoors and keep people, other vehicles, and combustible material away during this procedure.
•
Do NOT leave the vehicle unattended.
2.
Perform the Diesel Particulate Filter (DPF) Service Regeneration Enable procedure with a scan tool. Refer to Diesel
Particulate Filter DPF Regeneration Enable in SI.
3.
Perform a fuel trim reset with a scan tool.
4.
With a scan tool, reset the Engine Oil Life Remaining back to the original percentage recorded before the control
module was replaced, if available.
FOR CALIFORNIA, CONNECTICUT, DELAWARE, MARYLAND, MASSACHUSETTS, MAINE, OREGON, VERMONT,
WASHINGTON VEHICLES ONLY AND IN THE EVENT OF AN EPA-ORDERED EMISSIONS RECALL: Install a Recall
Identification Label upon recall completion. See General Motors Service Policies and Procedures Manual, Section 6.1.4
- Recall Identification Label, for details.
CALIFORNIA VEHICLES ONLY: Complete a “Proof of Correction” certificate and provide to the vehicle owner upon recall
completion.
Dealer Responsibility
All new, used, GM Certified Used, courtesy transportation vehicles, dealer shuttle vehicles, etc. in dealers' possession
and subject to this recall must be held and inspected/repaired per the service procedure of this bulletin before customers
take possession of these vehicles. Involved vehicles must be held and not delivered to customers, dealer-traded,
released to auction, used for demonstration, or any other purpose.
All GM Certified Used vehicles currently in the dealers’ inventory within the Certified Pre-Owned Inventory System
(CPOIS) will be de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting
an accepted/paid warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified
for sale within the CPOIS system, or once again be used in the CTP program.
Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of mileage, age of vehicle,
or ownership, from this time forward.
Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer
information indicated on the dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the
required correction according to the instructions contained in this bulletin. A copy of the customer letter is provided in this
bulletin for your use in contacting customers. Recall follow-up cards should not be used for this purpose, since the
customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this recall enters your vehicle inventory, or is in your dealership for service in
the future, you must take the steps necessary to be sure the recall correction has been made before selling or releasing
the vehicle.
***THE FOLLOWING 2 PARAGRAPHS ARE NOT FOR CANADA OR EXPORT***
When a California emissions recall is completed by a GM dealer, the dealer must provide the vehicle owner a “Proof of
Correction Certificate” which the owner may need to present to the California Department Of Motor Vehicles (DMV) when
renewing their vehicle registration. Without this correction certificate, the owner may be unable to renew their vehicle
registration.
Additional Certificates can be obtained, at no charge, from the 1Store application in GlobalConnect. Request GM Item
Number 1825 when ordering.
Dealer Reports
For dealers with involved vehicles, a listing with involved vehicles has been prepared and will be provided to U.S. and
Canadian dealers through the GM GlobalConnect Recall Reports, or sent directly to export dealers. The listing may
contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor
vehicle registration data for any purpose other than follow-up necessary to complete this recall is a violation of law in
Page 4 of 7
Product Emission Recall
17089 NOx Position 1 Sensor Replacement
several states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to
complete this recall.
Courtesy Transportation – For USA & Canada
Courtesy transportation is available for customers whose vehicles are involved in a product program and still within the
warranty coverage period. See General Motors Service Policies and Procedures Manual, Sections 1.4 and 6.1.10, for
courtesy transportation program details.
Customer Notification
USA & Canada - General Motors will notify customers of this recall on their vehicle (see copy of customer letter included
with this bulletin).
In order to ensure full protection under the emission warranty, and the right to participate in future recalls, the customer
notification letter recommends that customers have their vehicles serviced as soon as possible. It also advises that failure
to do so could legally be determined to be lack of proper maintenance.
Export - Letters will be sent to known owners of record located within areas covered by the US National Traffic and Motor
Vehicle Safety Act. For owners outside these areas, dealers should notify customers using the attached sample letter.
In order to ensure full protection under the emission warranty, and the right to participate in future recalls, the customer
notification letter recommends that customers have their vehicles serviced as soon as possible. It also advises that failure
to do so could legally be determined to be lack of proper maintenance
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of
conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained
technicians have the tools, equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT
assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your
vehicle may benefit from the information.
We Support
Voluntary Technician
Certification
Page 5 of 7
Product Emission Recall
17089 NOx Position 1 Sensor Replacement
June 2017
This notice applies to your vehicle, VIN: _____________________________________
Dear General Motors Customer:
This notice is sent to inform you that General Motors is conducting a voluntary emission recall that includes your
vehicle.
Reason For This Recall: Depending on driving habits, soot may build up on the engine NOx position 1 sensor and / or
oxygen sensor causing the vehicle Check Engine Indicator to illuminate.
An earlier correction for this condition (Product Emission Recall 15594) may, under certain driving conditions,
inadvertently cause the vehicle Check Engine Indicator to illuminate.
If your vehicle had not yet been serviced under recall 15594, and you previously received a letter notifying you
that General Motors had suspended repairs on recall 15594 in order to make additional improvements to the
repair software, those repairs are now ready to resume and your vehicles will receive those repairs under this
recall 17089.
Your vehicle will require repair regardless of whether recall 15594 was previously completed on your vehicle.
What Will Be Done: For vehicles that were not serviced under previous recall 15594, your dealer will replace the NOx
position 1 sensor, reprogram the engine control module with a modified calibration and initiate a Diesel Particulate Filter
cleaning cycle.
For vehicles previously serviced under recall 15594, dealers are to reprogram the engine control module with a
modified calibration and initiate a Diesel Particulate Filter cleaning cycle.
These services will be performed at no charge.
Your GM dealer will replace the NOx position 1 sensor, reprogram the Engine Control Module with a modified
calibration and initiate a Diesel Particulate Filter cleaning cycle. This service will be performed for you at no charge.
How Long Will The Repair Take? Because of service scheduling requirements, it is likely that your dealer will need
your vehicle longer than the actual service correction time of approximately 90 minutes.
What You Should Do: Please contact your Chevrolet dealer as soon as possible to arrange a service date and to
assure parts availability. Instructions for making this correction have been sent to your dealer. Please ask your dealer
if you wish to know how much time will be needed to schedule, process, and repair your vehicle.
If you have any questions or need any assistance, just contact your dealer or the appropriate Customer Assistance
Center at the number listed below.
Division
Chevrolet
Puerto Rico – English
Puerto Rico – Español
Virgin Islands
Number
1-800-630-2438
1-800-496-9992
1-800-496-9993
1-800-496-9994
Text Telephones (TTY)
1-800-833-2438
Emission Law Information: In order to ensure your full protection under the emission warranty made applicable to
your vehicle by state and federal law, and your right to participate in future recalls, it is recommended that you have
your vehicle serviced as soon as possible. Failure to do so could legally be determined to be lack of proper
maintenance of your vehicle. Also, your vehicle may fail a state or local emission inspection if this recall is not
accomplished.
IMPORTANT MESSAGE FOR CALIFORNIA RESIDENTS
The California Air Resources Board (CARB) requires vehicle emission recalls be completed prior to California
registration renewal. Uncorrected emission recalls will result in the inability to renew your California vehicle registration.
Page 6 of 7
Product Emission Recall
17089 NOx Position 1 Sensor Replacement
At the time of emission recall completion, your California dealer will issue a "Proof of Correction Certificate". Keep this
certificate and, if required, present it to the Department of Motor Vehicles when renewing your California registration as
proof of recall completion.
We are sorry to cause you this inconvenience; however, we have taken this action in the interest of your continued
satisfaction with our products.
Jeffrey M. Boyer
Vice President
Global Vehicle Safety
17089
Page 7 of 7
GLOBAL SAFETY FIELD INVESTIGATIONS
DCS4751
URGENT - DISTRIBUTE IMMEDIATELY
Date:
May 15, 2018
Subject: 17089 01 - Product Emission Recall
NOx Position 1 Sensor Replacement
Revised Warranty and Service Sections
Models: 2014-2015 Chevrolet Cruze Equipped with 2.0L Diesel Engine (LUZ)
To:
All General Motors Dealers
This bulletin is being revised to add the requirement for an SPS warranty claim
code to accompany warranty transaction submission, and to add notes to the
service procedure. Please discard all copies of bulletin 17089.
END OF MESSAGE
GLOBAL SAFETY FIELD INVESTIGATIONS
- Advanced VCI Box, Industry-leading J2534 Pass-Thru...
- High-Speed OEM-Level Diagnostics & Programming: Unlock true...
- Coverage for 17 Car Brands & Ultra Reliability: Works...
- User-Friendly RLink Platform & Expert Support: TOPDON’s...
- 6.6 ft USB-C Cable & Portable Storage Case: The RLink J...
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 17089 01
Replacement Service Bulletin Number:
MFR Communication Date: 2018-05-15
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Newly Added in 2026: 7 Reset Functions] The 2026 new version of the OBD2 scanner diagnostic tool CRP123X V3.0 Elite has new special functions for F.REE: Throttle Ad.aptation, Oil/SAS/BMS/Brake Reset, D-P.F Re.generation and ABS Service. Before you visit a mechanic, launch obd2 Scanner CRP123X Elite can perform a more in-depth diagnosis of the car system and provide accurate data within minutes. What's more, the list of compatible models has been expanded. Upgrading frequency is regular, occurring monthly even weekly.
- 🔥[FCA AutoAuth + CAN FD & DoIP] As an upgraded version of the LAUNCH CRP123X/CRP129X, FOXWELL NT614, and ANCEL FX2000, The Newest LAUNCH CRP123X V3.0 auto diagnostic scanner supports the following new protocols: CAN-FD for 2020 and newer G.M and Chrysler
models, as well as DoIP for V.olvo, Land Rover/Jaguar, and B.MW F/G chassis. With integrated AutoAuth, you can diagnose 2018 and newer FCA cars equipped with S.GW. Note: CAN-FD and DoIP protocols require an additional obd2 cable. *Menus vary by make, model, and year of gasoline or diesel engine vehicle. Email us your VIN data. - 🔥[No extra software fee. Works on 90 vehicle brands.] Most OBD2 scanners work with vehicles manufactured after 2001. However, the LUNCH OBD2 scanner is compatible with OBDII-equipped vehicles built after 1996 and works with more than 90 vehicle brands. One-click lifetime updates over WIFI 2.4&5.0Ghz keep the car software current and ensure constant coverage additions, diagnose vehicles from 1996 to 2026 with a massive global database. Android 8.1 ensures lightning-fast boot-up and processing.
- [Accurate & Intuitive Multi System Diagnosis] Will you be confused about what happens when the warning light of transmission, ABS, and SRS Airbag check engine flashes? Launch obd2 scanner diagnostic tool CRP123X V3.0 to pinpoint the problem components for a faster diagnosis for your car instead of taking your car to the dealership. Generate vehicle health reports with one click and share them via email over Wi-Fi to help avoid blind maintenance. And will turn off the warning light for you after fixing the problem, make to know more about your cars and do your own repair.
- [Multiple Display of Live Data + DTC Code Definition Explanation] Launch car tools show real-time data of oil temp, pressure, transmission temp, engine speed, coolant temperature, you will know which car part is abnormal. Data can be shown in a single, multi- graph, and merge two graphs for analysis（or 4-in-1 merged waveform graph),you can save, share, print, or email the overall inspection report for easier analysis.🔥Code Search,DTC Library provide massive information. Inbuilt “Feedback” module provides customized repair suggestions from our certified professionals.
- [2026 X431 PRO3 V+ Elite] A great value for the X431 series that differs from similar diagnostic tools by adding: 1) J2534 protocol for over $800 in savings; 2) CANFD/DOIP support for enhanced communications; 3) Configuration of over $900 worth of HD(heavy truck) modules, needed purchase HD diagnostic software by HD vehicle model for use.; 4) A 10.1 inch Gorilla screen with 1280*800 resolution and 80% more touch screen sensitivity
- [J2534 Protocol Scan Tool] The J2534 Direct Access Device can be used as a factory scanning tool at no cost to you, saving you over $2,000. You can easily expand your ECU protocol capabilities for Toyota, Honda, VW, BMW, Ford, GM, Chrysler, Mercedes-Benz and more. The LAUNCH X431 PRO3 V+ ELITE Scan Tool is equipped with the newly upgraded smartlinkC V2.0. smartLinkC is a communication interface that supports the J2534 specification. It can also be used as a J2534 PassThru device to implement the J2534 protocol with a PC that has OEM diagnostic software installed.The J2534 protocol is the only way to solve problems ranging from drivability and power loss to poor fuel economy
- [Top Hardware Configuration, Upgraded Version of V+] LAUNCH Diagnostic Scanner adopts Android 10.0 OS; CPU is 4-core processor with 2.0 GHz, which greatly improves the speed of running multi-tasks. 2.4GHz/5GHz; 6300mAh/7.6V ultra-large capacity battery; 10.1 inch Gorilla screen, sunlight readable, 8MP camera; Auto VIN; 4GB+64GB storage; 20x transfer rate to save more vehicle files and customer data; New TYPE A interface to connect expansion tools such as oscilloscopes, sensors, etc.; Supports more than 25 software languages such as EN, DE, FR, SP and JP
- [60+ Reset 3000+ Active Test] Full Bi-Directional Scan Tool quickly detects problems and guides repairs based on the response of actuators such as air conditioning clutches, windows, doors, mirrors and more. With the touch of a finger, you can easily send command signals from the scanner to a variety of modular actuators, testing component integrity and functionality in minutes or even seconds to determine if a replacement or repair is needed. In addition, the machine enjoys 60+ special services such as oil reset, ABS brake bleed, EPB, SAS, BMS, suspension, injector reset and more, and undergoes rigorous field testing to ensure availability
- [Unrivaled Coverage, Over 200 Vehicle Brands] LAUNCH X431 PRO3 V+ Elite Automotive Scanner is suitable for over 200 vehicle brands, including commercial vehicles and new energy vehicles. This professional car scanner supports: 1) J2534/D-PDU protocol for HD trucks; DoIP/CANFD for Land Rover/Jaguar, BMW F/G chassis, GM, etc.; 2) FCA Autoauth, covering 2018+ Chrysler/Dodge/Fiat, etc. New/old models, all covered. Includes frequently updated vehicle software and car coverage for faster support of other new models
- 🔥【2026 TOP HARDWARE AND SOFTWARE UPGRADE，UPGRADED OF CRP919E】LAUNCH scanner CRP919EBT wireless obd2 scanner has upgraded TOP HARDWARE CONFIGURATION and ADD NEWEST FUNCTIONS. The more FASTER and SMARTER CRP919EBT with 🔥Bluetooths & USB 2-in-1 connect🔥Android 10.0 OS🔥2.0Ghz 4 core high efficiency processor 4GB RAM+64GB ROM large storage🔥6300mAh large battery, more stable and longer lasting diagnostics🔥VAG Guided🔥ECU Code🔥Bi-directional Control🔥35+ Resets🔥CANFD&DOIP🔥FCA AutoAuth🔥Full System Diagnostics🔥2 Yrs Update🔥Newly add BST360 battery tester & I-TPMS & VSP600 endoscope🔥23+ Languages. Provide an unparalleled diagnostic experience at an affordable price.
- 🚗【CAN FD & DOIP & FCA, SUPER PROTOCOL】LAUNCH X431 CRP919EBT is equipped with the DBSCAR VII Bluetooth connector supporting CANFD and DoIP. The CRP919EBT automotive diagnostic scanner supports CAN FD protocol (compatible with post-2020 GM vehicles). It also meets DoIP protocol requirements (adapter sold separately) for compatibility with BMW (E & F chassis) models from 2017 onward. Autoauth for FCA SGW supports FCA vehicles including Chrysler models from 2017 and later.
- ✔️【ADVANCED ECU CODE, ADAPTATION, CALIBRATION & INITIALIZATION】The LAUNCH X431 CRP919EBT automotive scanner delivers exceptional ECU code capabilities for customized vehicle setups. It provides dealer-level functionality to streamline maintenance and repairs, enabling ECU matching and learning for enhanced customization.
- 👍【BIDIRECTIONAL CONTROL, 4000+ ACTIVE TESTS】LAUNCH OBD2 scanner CRP919EBT features bi-directional control - the most demanded capability among mechanics. When headlights or windows malfunction, repairs can be costly. With CRP919EBT, execute ECU commands and assess repair status through systems including ABS, windows, valves, wipers, and headlights - streamlining diagnostics while slashing repair expenses.
- 🥇【35+ MOST POPULAR RESET SERVICE FOR 160 MAKES】Same as Snap-on scanners, CRP919EBT scan tool delivers 35+ reset functions for 160+ vehicle models, including: service oil reset, throttle adaptation, steering angle calibration, brake pad replacement code, tire pressure reset, ABS bleeding, battery registration, gear signal learning, and injector code, etc.
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.