Corolla
1 Install D/C cut fuse (See page 2)...............................................

FUNCTIONAL OPERATION
Apply parking brake, cycle ignition “IG-ON,” place gear selector in “R,” turn on
lights and rear defogger, unlock all doors, and release fuel door and trunk hatch.

1
2
3
4
5
6
7
8
9

Check dome, courtesy, map, and sun visor lights* .................
Check warning/indicator lights, gauges, and horn ..................
Check windshield wipers and washers .....................................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights........................................
Check inside/outside rear view mirror
operation/adjustment....................................................................
Check USB and 12V power outlets ...........................................
Check audio/navigation*/backup camera* systems and
set clock .........................................................................................
Check sliding roof*........................................................................
Install shift-lock override button cover .......................................

OK

OK

BEFORE INSPECTION

May 2018

UNDER VEHICLE (ON HOIST)

Adjust\
Repair

2019 PRE-DELIVERY SERVICE CHECK SHEET
Adjust\
Repair

Market: USA

1 Remove disc brake anti-rust covers/anti-corrosion
wheel film* (remove just prior to customer delivery) ........
2 Inspect tires for defects/damage.................................................
3 Initialize Tire Pressure Warning System (TPWS)
(See page 2) ..................................................................................
4 Install wheel covers/caps/spare tire wheel covers* .................
5 Inspect for fuel, oil, coolant, and other fluid leaks ....................
6 Inspect under the vehicle for damage, rust, etc. ......................
7 Visually check bolts and nuts on chassis and powertrain
for looseness ..................................................................................
8 Install rubber body plugs (stored in glove box or
center console)*.............................................................................

ROAD TEST
A complete road test helps promote customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Readings

WALKAROUND INSPECTION
Starting at the left front door, check window and door lock operation from master
power switch, if equipped. Continue around vehicle in a counterclockwise
direction checking each door and window operation, child door locks, seat belts,
interior condition, all lights, and luggage compartment contents. Finish by
checking headlight aim.

1 Check Smart Key System* .......................................................
2 Check door and door lock operation, including each
wireless remote control/theft deterrent system * ......................
3 Check window operation .............................................................
4 Check that engine starts with all keys .......................................
5 Check that child safety door locks are in normal
(unlocked) position .......................................................................
6 Check seats and seat belt operation .........................................
7 Check rear defogger/rear view mirror defogger*.....................
8 Check side marker, tail, backup, and license plate lights ......
9 Check luggage compartment light* and trim appearance ......
10 Adjust spare tire pressure, inspect for damage, and check
jack and tool installation...............................................................
11 Check headlight aim.....................................................................

UNDER HOOD
1
2
3
4
5

Check engine oil and ATM* fluid levels.....................................
Check brake and clutch* fluid levels..........................................
Check engine coolant level .........................................................
Check windshield washer fluid level ..........................................
Check battery State-Of-Charge (SOC) using digital
battery system analyzer (SOC reading: ___________%) .
6 Inspect for fuel, oil, coolant, and other fluid leaks ...................
Notes:

Reading Before Test: _______________ Reading After Test: ________________

1
2
3
4
5
6
7
8
9
10
11
12

Check cold engine operation .......................................................
Check engine operation during warm -up ..................................
Check engine operation at normal operating temperature .....
Check transmission operation .....................................................
Check brake and parking brake operation ................................
Check steering operation and off-center/vehicle pull/flutter ...
Inspect for abnormal noise and vibration ..................................
Inspect for squeaks and rattles ...................................................
Check heater and A/C operation ................................................
Check cruise control operation*..................................................
Check front seat heater operation*.............................................
Set/calibrate compass* (See page 2) ........................................

FINAL INSPECTION AND CLEANING
1 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer) ..............
2 Visually inspect all interior parts for installation, damage,
fit, dirt, etc. ......................................................................................
3 Verify floor mat application and install using
retaining clips* .............................................................................
4 Remove Rapgard™ and clear protective bumper film *...........
5 Wash and clean vehicle ...............................................................
6 Inspect paint finish for scratches, chips, rust, dents,
damage, etc....................................................................................
7 Inspect exterior body parts for proper installation,
damage, rust, etc...........................................................................
8 Place service reminder sticker on inside of windshield, top
left corner........................................................................................
9 Place Owner’s Manual portfolio* in glove box ..........................
10 Perform Techstream Health Check ............................................
11 Install front license plate and mounting bracket*
(See page 2) ..................................................................................
* Inspect or install when equipped/required.

Completion and retention of this f orm is required to comply with Toy ota’s Warranty Policy .

Technician’s Signature

Serv ice Manager’s Signature

Name (Please Print)

Name (Please Print)

Dealer Code

Date

Dealer Name

Vehicle Identif ication Number (Sticker)
We hereby certify that all items on this form have been checked and corrected for proper operation as required.

D/C CUT FUSE INSTALLATION
To minimize battery discharge, the D/C cut fuse has been removed and is
stored in the engine compartment Relay Block. Install the D/C cut fuse and
confirm all related DTCs are cleared.

1

DTC Clearing Procedure
1.

Connect Techstream.

2.

Cycle the ignition switch to the “IG-ON” position.

3.

Using Techstream, check any other codes being output.

4.

Erase DTCs (B1247) and Freeze Frame Data.

2

1 Install D/C Cut Fuse (30A) Here (Original Location)
2 Remove This D/C Cut Fuse (30A)

TIRE PRESSURE WARNING SYSTEM (TPWS) INITIALIZATION
Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does not have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a
Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will display
on the Health Check results screen. Adjust the tire pressure when the tires are cold.

COMPASS CALIBRATION
Refer to the Repair Manual for the Calibration procedure for vehicles equipped with a compass in the rear view mirror.
NOTE
 Do not perform calibration of the compass in a place where the Earth’s magnetic field is subject to interference
(underground parking, under a steel tower, between buildings, roof parking, near a railroad crossing, near a large
vehicle, etc.).
 During calibration, do not operate electric systems (moon roof, power windows, etc.) as they may interfere with
the calibration.

FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION
1.

Insert the front license plate into the tabs on the bracket.
1

2.

Attach the clip of bracket to the upper lip of second air
intake and rotate the bracket upwards.

3.

Align the holes on the license plate and license plate
bracket with the dimples on the lower grille.

6

1
2
3
4
5
6

Dimple
Second Air Intake
Front License Plate Bracket
License Plate
Clip
Rotate Bracket

5
2

3
4

4.

1 Self-tapping Screw

Screw the two self-tapping screws directly into the
dimples to install the front license plate and the
front license plate bracket.
NOTICE
 Do not pre-drill holes into the bumper.
 Do not overtighten the self-tapping screws.
1