NUMBER:
GROUP:
DATE:

18-025-14
Vehicle Performance
April 01, 2014

This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of Chrysler Group LLC.

HELP USING THE wiTECH DIAGNOSTIC APPLICATION FOR FLASHING AN ECU IS
AVAILABLE BY SELECTING “HELP” THEN “HELP CONTENTS” AT THE TOP OF
THE wiTECH DIAGNOSTIC APPLICATION WINDOW.
THE wiTECH SOFTWARE LEVEL MUST BE AT RELEASE 14.03 OR HIGHER TO
PERFORM THIS PROCEDURE.
SUBJECT:
Flash: Powertrain System Improvements/Enhancements
OVERVIEW:
This bulletin involves selectively erasing and reprogramming the Powertrain Control
Module (PCM) with new software.
MODELS:
2014

(DS)

Ram 1500

2014

(DJ)

Ram 2500

NOTE: This bulletin applies to DS vehicles equipped with a 3.6L engine (sales code
ERB) built on or before January 17, 2014 (MDH 0117XX), DS vehicles
equipped with a 5.7L engine (sales code EZH) built on or before February 10,
2014 (MDH 0210XX) and DJ vehicles equipped with a 5.7L engine (sales code
EZC) built on or before February 20, 2014 (MDH 0220XX).
SYMPTOM/CONDITION:
The following powertrain system improvements/enhancements are included in this
software release:
•

•
•

Enhanced Automatic Oil Change Indicator(EAOCI) system enhancements that force
the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle
duty cycle information used in the EAOCI calculation is stored in the PCM and
cannot be recovered/transferred when the controller is replaced. As a result, the
severe duty cycle is used in these scenarios to ensure the customer receives a
timely oil change required message.
Corrected a generic scan tool display issue regarding Mode 6 data accuracy.
Improved transmission Quick Learn routine performance (Applies only to DJ
vehicles)

DIAGNOSIS:

18-025-14

-2-

Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in
TechCONNECT, verify all engine systems are functioning as designed. If DTC's other than
the one listed above are present record them on the repair order and repair as necessary
before proceeding further with this bulletin.
REPAIR PROCEDURE:
NOTE: Install a battery charger to ensure battery voltage does not drop below 13.2
volts. Do not allow the charging voltage to climb above 13.5 volts during the
flash process.
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
1. Reprogram the PCM with the latest software. Help using the wiTECH Diagnostic
Application for flashing control modules is available through the wiTECH Diagnostic
Application. For instructions select the “HELP” tab on upper portion of the wiTECH
window, then “HELP CONTENTS”. This will open the Welcome to wiTECH Help
screen where help topics can be selected.
2. After PCM reprogramming, the following must be performed:clear any DTC's that
may have been set in other modules due to reprogramming. The wiTECH application
will automatically present all DTCs after the flash and allow the tech to clear them.
POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
Labor Operation
No:
18-19-06-9A

Description
Module, Powertrain Control (PCM) Reprogram (1 - Semi-Skilled)

Skill Category
8 - Engine
Performance

Amount
0.2 Hrs.

NOTE: The expected completion time for the flash download portion of this
procedure is approximately 5 minutes. Actual flash download times may be
affected by vehicle connection and network capabilities.
FAILURE CODE:
FM

Flash Module