NUMBER:

26-001-13

GROUP:

Miscellaneous

DATE:

May 03, 2013

This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of Chrysler Group LLC.

THIS SERVICE BULLETIN IS ALSO BEING RELEASED AS RAPID RESPONSE
TRANSMITTAL (RRT) 13-030. ALL APPLICABLE SOLD RRT VIN's HAVE BEEN
LOADED. TO VERIFY THAT THIS RRT SERVICE ACTION IS APPLICABLE TO THE
VEHICLE, USE VIP OR PERFORM A VIN SEARCH IN TECHCONNECT.
SUBJECT:
Dodge Dart Racetrack Lighting Customer Initiative
OVERVIEW:
This bulletin involves removing and replacing the center rear lamp secured to the decklid
assembly.
MODELS:
2013

(PF)

Dart (U.S. Markets Only)

NOTE: This bulletin applies to vehicles equipped without (Sales Code LBQ) LED
racetrack lighting tail lamps that are not an SE model.
SYMPTOM/CONDITION:
The customer received a promotional flyer and/or is aware of the promotional pricing for a
new center rear lamp that is equipped with the racetrack lighting function for all models
except SE.
DIAGNOSIS:
If a customer’s VIN is listed in VIP or your RRT VIN list, perform the repair.
PARTS REQUIRED:
Qty.

Part No.

Description

1 (AR)

82213354

Turn Signals, Racetrack Lighting (Without
(Sale code GXD) Passive Entry)

1 (AR)

82213687

Turn Signals, Racetrack Lighting (With (Sale
code GXD) Passive Entry)

REPAIR PROCEDURE:
1. Open the deck lid.
2. Disconnect and isolate the battery negative cable.

26-001-13

-2-

3. Using Trim Stick C-4755 , remove the access covers (1) from the decklid insulator/trim
panel (Fig. 1).

Fig. 1 Access Covers
1 - Access Covers

4. Route the manual trunk release handle (1) through the decklid insulator/trim panel
(Fig. 2).

Fig. 2 Trunk Release Handle
1 - Trunk Release Handle

-3-

26-001-13

5. Remove the fasteners (2) securing the decklid insulator/trim panel (1) from the decklid
(Fig. 3).

Fig. 3 Decklid Trim Cover
1 - Trim Panel
2 - Fasteners

6. Route the decklid insulator/trim out from behind the decklid over slam bumpers.
7. Remove the decklid insulator/trim panel (1) (Fig. 3).
8. Remove the five nuts (3) that secure the center tail lamp (2) to the inside of the deck
lid inner panel (Fig. 4).

26-001-13

-4-

Fig. 4 Center Decklid Lamp Fasteners
1 - Decklid
2 - Center Tail Lamp
3 - Five Fasteners

9. Remove the center lamp wiring connector from the decklid assembly as shown in (Fig.
5).

Fig. 5 Connector Removal
1 - Connector
2 - Trim Removal Tool

-5-

26-001-13

10. Disconnect the body wire harness connector from the center tail lamp (1) pigtail wire
harness connector (2) on the right end of the lamp (Fig. 6).
11. Loosen but do not remove the two retention feature nuts (3) on each end of the lamp
(Fig. 6).
12. Squeeze each of the two retention features (4) on each end of the lamp to disengage
the lamp from the deck lid (Fig. 6).

Fig. 6 Disconnect Electrical Connector
1 - Center Tail Lamp Connector
2 - Body Side Electrical Connector
3 - Retention Feature Nuts
4 - Retention Features

13. From the outside of the vehicle, grasp each end of the center tail lamp (1) and pull
straight rearward to remove the lamp from the outside of the deck lid (2) (Fig. 7).

26-001-13

-6-

Fig. 7 Center Rear Decklid Lamp
1 - Center Tail Lamp
2 - Decklid

14. Position the new center tail lamp unit (1) into the lower deck lid (2) lamp opening (Fig.
7).
15. Using hand pressure, press firmly and evenly on the two outboard ends of the center
tail lamp to seat the retention features into the deck lid inner panel.
16. From the inside of the deck lid (1), install and tighten the five nuts (3) that secure the
center tail lamp (2) to the deck lid inner panel. Tighten the nuts securely (Fig. 8).

-7-

26-001-13

Fig. 8 Center Decklid Lamp Fasteners
1 - Decklid
2 - Center Tail Lamp
3 - Five Fasteners

17. Securely tighten each of the two nuts (2) that secure the two retention features (3) on
each end of the center tail lamp (4) to the deck lid inner panel (Fig. 9).
18. Connect the body wire harness connector to the center tail lamp pigtail wire connector
(1) (Fig. 9).

26-001-13

-8-

Fig. 9 Connect Electrical Connector
1 - Center Tail Lamp Electrical Connector
2 - Retention Feature Nuts
3 - Retention Features
4 - Center Tail Lamp

19. Reconnect the battery negative cable.
20. Verify the new rear center lamp race track lighting feature functions correctly by
engaging and disengaging the brake pedal.
21. Position the decklid insulator/trim panel near the vehicle.
22. Route the manual trunk release handle (1) through the decklid insulator/trim panel
(Fig. 10).

-9-

26-001-13

Fig. 10 Trunk Release Handle
1 - Trunk Release Handle

23. Align the decklid insulator/trim panel (1) on the decklid (Fig. 11).
24. Install the fasteners (2) securing the decklid insulator/trim panel (1) into the decklid
(Fig. 11).
25. With the use of a trim stick, route the overslam bumper openings in decklid
insulator/trim panel over the decklid overslam bumpers and insert fully (Fig. 11).

26-001-13

-10-

Fig. 11 Decklid Trim Cover
1 - Trim Panel
2 - Fasteners

26. Install the access covers (1) to the decklid insulator/trim panel (Fig. 12).

Fig. 12 Access Covers
1 - Access Covers

27. Close the decklid.
TIME ALLOWANCE:

-11Labor Operation
No:
08-50-85-94

Description
Remove and Replace Center Rear Tail Lamp
Mounted On Decklid Assembly (1- Semi-Skilled)

FAILURE CODE:
ZZ

Service Action

26-001-13
Amount
0.3 Hrs.