PRIUS C
01 Install D/C Cut fuse (see page 2) ...................................
02 Install radio antenna* ......................................................

FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse; turn on
lights and rear defogger. Unlock doors; release fuel door.

01
02
03
04
05
06
07
08
09
10
11

Check dome, courtesy, map, and sun visor lights* ..........
Check warning/indicator lights, buzzers, and horn .........
Check windshield wipers and washers ............................
Check headlights, instrument lights, dimmer switch, turn
signals, emergency flashers, and brake lights ................
Check inside/outside rear view mirror operation/adjustment*
Check cigarette lighter* and power outlets ......................
Check audio/navigation*/backup camera* systems and
set clock .........................................................................
Verify Entune/Navigation software version (Display
Audio, Non-HDD Type only)* ........................................
Check multi-information display and trip information on
center display* ................................................................
Install shift-lock override button cover* ...........................
Check sliding roof* ..........................................................

WALKAROUND INSPECTION
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.

01 Check Smart Key System* ..........................................
02 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ..............
03 Check window operation ................................................
04 Check that engine starts with all keys .............................
05 Check that child safety door locks are in normal
(unlocked) position* .......................................................
06 Check seats and seat belt operation ...............................
07 Check rear defogger/rear view mirror defogger* .............
08 Check side marker, tail, backup, and license plate lights
09 Check luggage compartment light* and trim
appearance ....................................................................
10 Adjust spare tire pressure, inspect for damage, and
check jack and tool installation ......................................
11 Check headlight aim ......................................................
12 Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading:_____%) ..................

UNDER HOOD
01
02
03
04
05

Check engine oil level ......................................................
Check brake and power steering fluid levels ...................
Check engine coolant level ..............................................
Check inverter coolant level ............................................
Check windshield washer fluid level ................................
06 Inspect for fuel, oil, coolant, and other fluid leaks ............

BATTERY MAINTENANCE
01 Perform HV battery check and maintenance .............

UNDER VEHICLE (ON HOIST)

Adjust/
Repair

December 2014

OK

OK

BEFORE INSPECTION

Adjust/
Repair

2015 PRE-DELIVERY SERVICE CHECK SHEET

01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* ......................................................................
02 Inspect tires for defects/damage ......................................
03 Initialize Tire Pressure Warning System (TPWS)
(see page 2) ....................................................................
04 Install wheel caps* ...........................................................
05 Install front wheel opening extension pads (see page 2) .
06 Inspect for fuel, oil, coolant, and other fluid leaks ............
07 Inspect under the vehicle for damage, rust, etc. ..............
08 Visually check bolts and nuts on chassis and powertrain
for looseness....................................................................
09 Install rubber body plugs (stored in glove box or console)*
10 Check hybrid transaxle fluid .............................................

ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Readings
Reading Before Test: _______________ Reading After Test: ________________

01
02
03
04
05
06
07
08
09
10
11

Check cold engine operation............................................
Check engine operation during warm-up .........................
Check engine at normal operating temperature ...............
Check hybrid transaxle operation.....................................
Check brake and parking brake operation .......................
Check steering operation & off-center/vehicle pull/flutter .
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check heater and A/C* operation ...................................
Check cruise control operation* .......................................
Check front seat heater operation* .................................

FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove protective covers just before delivery
to customer) .....................................................................
02 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
03 Verify floor mat application and install using
retaining clips* ...............................................................
04 Remove Rapgard™ and clear protective bumper film* ....
05 Wash and clean vehicle ...................................................
06 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
07 Place oil change sticker on inside of windshield, top
left corner .........................................................................
08 Inspect exterior body parts for proper installation,
damage, rust, etc. ............................................................
09 Install front license plate* (see page 2) ..........................
10 Place Owner’s Guide and first aid kit portfolio* in glove
box ..................................................................................
11 Perform Techstream Health Check .................................
* Inspect or install when equipped/required.

Completion and retention of this form is required to comply with Toyota’s Warranty Policy.

TECHNICIAN’S SIGNATURE

SERVICE MANAGER’S SIGNATURE

NAME (PLEASE PRINT)

NAME (PLEASE PRINT)

Date

Dealer Name

Dealer Code

We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)

D/C CUT FUSE INSTALLATION
The D/C Cut fuse (30 A) has been removed at the assembly plant to
reduce parasitic current draw in transit and storage. Reinstall the D/C Cut
fuse to the original location.

1

2
1 Storage Location
2 Installation Location

TPWS INITIALIZATION
Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does not have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a
Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will be
displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.

FRONT WHEEL OPENING EXTENSION PAD INSTALLATION
The front wheel opening extension pad set (right and left front wheel
opening extension pads and 4 tapping screws) is loaded in the luggage
compartment at the assembly plant to avoid damage in transit.
1. Hook the retainers of the front left wheel opening extension pad
through the installation holes on the fender liner and temporarily fix it
to the installation position.
NOTE
There is a distinguishable mark on each pad.
2. Tighten the 2 tapping screws.
3. Repeat for the right side.

FRONT LICENSE PLATE INSTALLATION*
1. Align the installation holes of the front license plate with the dimples on
the front bumper.
NOTICE
• Do NOT pre-drill holes into the bumper.
• Do NOT overtighten the self-tapping screws.

1

2. Using 2 self-tapping screws, install the front license plate by directly
screwing the tapping screws into the dimples.

2

Length: 15.0 — 20.0 mm (0.60 — 0.79 in.)
Diameter: 6.0 mm (0.24 in.)

3

1 Dimples
2 License Plate
3 Self-tapping Screws