Prius V
1 Remove disc brake anti-rust covers/anti-corrosion
wheel film* (remove just prior to customer delivery)……..
2 Inspect tires for defects/damage ……………………………
3 Activate and initialize Tire Pressure Warning System
(TPWS) (See page 2) ………...............................................
4 Install wheel covers/caps/spare tire wheel covers* ……….
5 Inspect for fuel, oil, coolant, and other fluid leaks …………
6 Inspect under the vehicle for damage, rust, etc. ……………
7 Visually check bolts and nuts on chassis and powertrain
for looseness…………………………………………………….
8 Install rubber body plugs*……………………………………..
9 Check hybrid transaxle fluid level ……………………..…….

FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse; turn
on lights and rear defogger. Unlock all doors, release fuel door, release trunk hatch.

5
6
7
8
9
10

Check dome, courtesy, map, and sun visor lights*………...
Check warning/indicator lights, gauges, and horn.…..…….
Check windshield wipers and washers…..…………………
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ……………………….
Check inside/outside rearview mirror operation/adjustment
Check cigarette lighter* and power outlets………………….
Check audio/navigation*/backup camera systems and
set clock.……………………….……………………………….
Check multi-information display and trip information on
center display* …………………………………………………
Install shift-lock override button cover* ………….…….…...
Check sliding roof* …………………………………………….

ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and driving
performance.
Enter Odometer Readings
Reading Before Test: _______________ Reading After Test: ________________

WALKAROUND INSPECTION

1
2
3
4
5
6
7
8
9
10
11

Starting at the left front door, check window and door lock operation. Continue
around the vehicle in a counterclockwise direction checking each door and window
operation, child door locks, seat belts, interior condition, all lights, and luggage
compartment contents. Finish by checking headlight aim and continue into UNDER
HOOD checks.

1
2
3
4
5
6
7
8
9
10
11

Check Smart Key System*…………………………………..
Check window operation………………………………………
Check that engine starts with all keys ……………….………
Check that child safety door locks are in normal
(unlocked) position…………………………………………….
Check seats and seat belt operation………………………...
Check rear defogger/rear view mirror defogger*…………..
Check side marker, tail, backup, and license plate lights …
Check luggage compartment light* and trim appearance…
Adjust spare tire pressure, inspect for damage, and check
jack and tool installation………………………………………
Check headlight aim…………………………………………...
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading:________%) …………..

Check cold engine operation …………………………………
Check engine operation during warm-up ……………………
Check engine at normal operating temperature ……………
Check hybrid transaxle operation…………………………….
Check brake and parking brake operation ………………….
Check steering operation and off-center/vehicle pull/flutter
Inspect for abnormal noise and vibration ……………………
Inspect for squeaks and rattles ………………………………
Check front and rear* heater and A/C operation……………
Check cruise control operation* ……………………………...
Check front seat heater/ventilation operation* ……………..

FINAL INSPECTION AND CLEANING
1 Remove interior protective covers, unnecessary labels,
tags, etc. (remove just before delivery to customer) ………
2 Visually inspect all interior parts for installation, damage, fit,
dirt, etc. ………………………………………………………..
3 Verify floor mat application and install using
retaining clips*………………………………………..............
4 Verify green light is illuminated on SOS (Safety Connect)
button*…………………………………………………………...
5 Remove Rapgard™ and clear protective bumper film*……
6 Wash and clean vehicle……………………………………….
7 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ……………………………………………………
8 Inspect exterior body parts for proper installation, damage,
rust, etc. ……………………………………………………….
9 Place oil change sticker on inside of windshield, top
left corner………………………………………………………..
10 Install front license plate and mounting bracket* (see
page 2)………………………………………………………..…
11 Place Owner’s Guide and first aid kit portfolio* in glove box
12 Perform Techstream Health Check…………………………..

UNDER HOOD
1
2
3
4
5
6

OK

UNDER VEHICLE (ON HOIST)

1 Install Short Pin (See Page 2)…………………………………

1
2
3
4

May 2016
Adjust\
Repair

OK

BEFORE INSPECTION

Adjust\
Repair

2017 PRE-DELIVERY SERVICE CHECK SHEET

Check engine oil level…………………………………………
Check brake fluid level………………………………………..
Check engine coolant level …………………………………..
Check inverter coolant level…………………………………
Check windshield washer fluid level…………………………
Inspect for fuel, oil, coolant, and other fluid leaks………….

BATTERY MAINTENANCE*
1 Perform HV battery check and maintenance……………
* Inspect or install when equipped/required.
Notes:

Completion and retention of this form is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE

NAME (PLEASE PRINT)
Date

Dealer Name

SERVICE MANAGER’S SIGNATURE

We hereby certify that all items
on this form have been
checked and corrected for
proper operation as required.

NAME (PLEASE PRINT)
Dealer Code

Vehicle Identification Number (Sticker)

SHORT PIN INSTALLATION
To minimize battery discharge, the Short Pin has been removed and is
stored in the engine compartment Relay Block. Install the Short Pin and
confirm all related DTCs are cleared.
DTC Clearing Procedure
1. Connect Techstream to DLC3.
2. Cycle the ignition switch to the “IG-ON” position.
3. Using Techstream, check any other codes being output.
4. Erase DTCs (B1650, B1794, U0142, and U0155) and Freeze Frame Data.
NOTE
If any DTCs besides B1650, B1794, U0142, and U0155 remain,
repair the applicable system according to the Repair Manual.

1 Storage Location
2 Installation Location

3 Front

TIRE PRESSURE WARNING SYSTEM (TPWS) ACTIVATION AND INITIALIZATION
Activation Procedure
1. Connect Techstream to DLC3.
2. Cycle the IG switch to the “IG-ON” position and check that the Low Tire Pressure Warning Light blinks for 1 minute and then
remains illuminated.
3. Press or remove the valve core to reduce the tire inflation pressure rapidly by 6 psi (0.4 kgf/cm2, 40 kPA), or more, within
30 seconds.
4. Using Techstream, check for DTCs (C2111-C2114). If no DTCs are stored, continue to step 5. If these DTCs are stored,
repeat step 3.
5. Adjust all tires to the standard tire inflation pressure, as indicated on the Tire and Loading information label inside the driver’s
door jamb.
6. Check the tire pressure values of all the tires using Techstream. TPWS ECU/Datalist/TIREPRESS 1 – 4
NOTE
If DTCs C2111-C2114 are present after repeating step 3, lift the vehicle and rotate each tire so that the tire pressure warning
valve/sensor is at the top of the wheel well. Repeat step 3 again.
Initialization Procedure
Refer to the Repair Manual for the initialization procedure.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform
a Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will
be displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.

FRONT LICENSE PLATE & MOUNTING BRACKET INSTALLATION*
1. Align holes “A” of the mounting bracket with the dimples on the front bumper
cover. Mark the location of holes “B” in the front bumper cover.

2. Drill 2 relief holes with a diameter of 11 mm (0.43 in.) at the hold “B” marks on
the front bumper cover to prevent the license plate retaining bolt from contacting
the cover.
3. Install the mounting bracket to the front bumper cover by attaching the
2 self-tapping screws into the dimples.
4. Install the front license plate to the mounting bracket using bolts with the
following dimensions.
Length: 20.0–25.0 mm (0.79–0.98 in.)
Diameter: 6.0 mm (0.24 in.)
Pitch: 1.0 mm (0.04 in.)

NOTICE
Do NOT pre-drill holes into the bumper.
Do NOT overtighten the self-tapping screws.

1 Bolts
2 License Plate
3 Self-tapping Screws

4 Mounting Bracket
5 Mark and Drill Holes
6 Dimples